Ali Hemmasian Ettefagh
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Ali Hemmasian Ettefagh has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
Shengmin Guo
4 shared publicationsHao Wen
3 shared publicationsFengyuan Lu
2 shared publicationsJuan Gao
2 shared publications- Shengmin Guo
Department of Mechanical and Industrial Engineering, Louisiana State University, Baton Rouge, LA 70803, USA
2 shared publications - Ali Haghshenas
Department of Mechanical and Industrial Engineering, Louisiana State University, Baton Rouge, LA 70803, USA
1 shared publication
Latest Publications
- 1 March 2020
- Published by Elsevier in Surface and Coatings Technology
- Vol. 385
Laser nitriding of titanium surfaces for biomedical applications
- 1 March 2020
- Published by Elsevier in Surface and Coatings Technology
- Vol. 385
Laser nitriding of titanium surfaces for biomedical applications
- 1 January 2020
- Published by Elsevier in Surface and Coatings Technology
- Vol. 381
Laser surface modifications of Fe-14Cr ferritic alloy for improved corrosion performance
- 1 January 2020
- Published by Elsevier in Surface and Coatings Technology
- Vol. 381
Laser surface modifications of Fe-14Cr ferritic alloy for improved corrosion performance
- 30 April 2019
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 31 (2) , 022012
Laser surface treatment of Ti-10Mo alloy under Ar and N2 environment for biomedical application
This paper evaluated the effects of laser beam irradiation based surface modifications of Ti-10Mo alloy samples under either Ar or N2 environment to the corrosion resistance and cell integration properties. The surface morphology and element distributions of Ti-10Mo samples after laser surface treatments were evaluated using a scanning electron microscope, energy-dispersive x-ray spectroscopy, and x-ray photoelectron spectroscopy. Phase analysis was performed with x-ray diffraction. The electrochemical behavior of the Ti-10Mo samples was evaluated in simulated body fluid maintained at 37 ± 0.5 °C, and a cell-material interaction test was conducted using the MLO-Y4 cells. Laser surface modification in the Ar environment enhanced corrosion behavior, but did not affect the surface roughness, element distribution, or cell behavior, compared to the untreated samples. Processing the Ti-10Mo alloy in N2 formed a much rougher TiN surface that improved both the corrosion resistance and cell-material integration compared with the other two conditions.
- 30 April 2019
- Published by Laser Institute of America in Journal of Laser Applications
- Vol. 31 (2) , 022012
Laser surface treatment of Ti-10Mo alloy under Ar and N2 environment for biomedical application
This paper evaluated the effects of laser beam irradiation based surface modifications of Ti-10Mo alloy samples under either Ar or N2 environment to the corrosion resistance and cell integration properties. The surface morphology and element distributions of Ti-10Mo samples after laser surface treatments were evaluated using a scanning electron microscope, energy-dispersive x-ray spectroscopy, and x-ray photoelectron spectroscopy. Phase analysis was performed with x-ray diffraction. The electrochemical behavior of the Ti-10Mo samples was evaluated in simulated body fluid maintained at 37 ± 0.5 °C, and a cell-material interaction test was conducted using the MLO-Y4 cells. Laser surface modification in the Ar environment enhanced corrosion behavior, but did not affect the surface roughness, element distribution, or cell behavior, compared to the untreated samples. Processing the Ti-10Mo alloy in N2 formed a much rougher TiN surface that improved both the corrosion resistance and cell-material integration compared with the other two conditions.
- 15 April 2019
- Published by American Chemical Society (ACS) in ACS Biomaterials Science & Engineering
- Vol. 5 (5) , 2147-2159
Improvement of Tribological and Biocompatibility Properties of Orthopedic Materials Using Piezoelectric Direct Discharge Plasma Surface Modification
Various types of alloys and polymers are utilized in orthopedic implants. However, there are still several issues accompanied by the use of prosthetic materials, such as low wear performance and catastrophic failure. Surface enhancement of biomaterials is a promising method that can improve the success rate of prosthetic operations without negatively affecting their bulk properties while improving the biocompatibility of implants and reducing infections. Nonthermal plasma treatment has become a ubiquitous surface modification method in sterilization and healthcare applications. However, the clinical applications of such an approach have been limited due to the lack of detailed studies delineating the wear behavior and biocompatibility of implants after plasma treatment. In this study, we have employed a handheld piezoelectric direct discharge (PDD) plasma generator to modify the surface of two common metallic (Ti6Al4V) and nonmetallic (GUR1020 polymer) biomaterials used typically in joint and disc replacements. We have observed an approximately 60-fold reduction in tribological wear rate along with a 2- to 3-fold increase in the biocompatibility properties of plasma coated samples compared to noncoated (untreated) surfaces, respectively. Our study introduces a novel application of nonthermal PDD plasma technology that is capable of increasing the quality and success rate of joint and disc replacements.
- 15 April 2019
- Published by American Chemical Society (ACS) in ACS Biomaterials Science & Engineering
- Vol. 5 (5) , 2147-2159
Improvement of Tribological and Biocompatibility Properties of Orthopedic Materials Using Piezoelectric Direct Discharge Plasma Surface Modification
Various types of alloys and polymers are utilized in orthopedic implants. However, there are still several issues accompanied by the use of prosthetic materials, such as low wear performance and catastrophic failure. Surface enhancement of biomaterials is a promising method that can improve the success rate of prosthetic operations without negatively affecting their bulk properties while improving the biocompatibility of implants and reducing infections. Nonthermal plasma treatment has become a ubiquitous surface modification method in sterilization and healthcare applications. However, the clinical applications of such an approach have been limited due to the lack of detailed studies delineating the wear behavior and biocompatibility of implants after plasma treatment. In this study, we have employed a handheld piezoelectric direct discharge (PDD) plasma generator to modify the surface of two common metallic (Ti6Al4V) and nonmetallic (GUR1020 polymer) biomaterials used typically in joint and disc replacements. We have observed an approximately 60-fold reduction in tribological wear rate along with a 2- to 3-fold increase in the biocompatibility properties of plasma coated samples compared to noncoated (untreated) surfaces, respectively. Our study introduces a novel application of nonthermal PDD plasma technology that is capable of increasing the quality and success rate of joint and disc replacements.
- 9 November 2018
- Published by ASME International
Phase Evolution and Corrosion Performance of Laser Processed Oxide Dispersion Strengthened Ferritic Alloys
The application of laser processing as a surface treatment method on oxide dispersion strengthened (ODS) Fe-14Cr ferritic alloys, Fe-14Cr-3W-0.3Ti-xY2O3 (x = 0.3, 0.6, 0.9) (wt%), was examined in this paper. The ODS ferritic alloys with different amount of Y2O3 particles were prepared by mechanical milling and subsequently consolidated by spark plasma sintering (SPS). The effect of surface laser processing on the corrosion behavior was investigated for these ODS alloys with different oxide contents. The corrosion behaviors of SPS consolidated ODS samples with subsequent laser melting/solidification were examined by the means of electrochemical tests and compared with the untreated ODS samples in salt water. Results indicated that for samples without laser treatment, powders are mainly in their elemental state. However, after laser processing, the formation of passive layer and the improvement in the corrosion resistance are noticeable. CALculation of PHAse Diagrams (CALPHAD) calculations were used to identify the equilibrium phases and compared well with the experimental results.
- 9 November 2018
- Published by ASME International
Phase Evolution and Corrosion Performance of Laser Processed Oxide Dispersion Strengthened Ferritic Alloys
The application of laser processing as a surface treatment method on oxide dispersion strengthened (ODS) Fe-14Cr ferritic alloys, Fe-14Cr-3W-0.3Ti-xY2O3 (x = 0.3, 0.6, 0.9) (wt%), was examined in this paper. The ODS ferritic alloys with different amount of Y2O3 particles were prepared by mechanical milling and subsequently consolidated by spark plasma sintering (SPS). The effect of surface laser processing on the corrosion behavior was investigated for these ODS alloys with different oxide contents. The corrosion behaviors of SPS consolidated ODS samples with subsequent laser melting/solidification were examined by the means of electrochemical tests and compared with the untreated ODS samples in salt water. Results indicated that for samples without laser treatment, powders are mainly in their elemental state. However, after laser processing, the formation of passive layer and the improvement in the corrosion resistance are noticeable. CALculation of PHAse Diagrams (CALPHAD) calculations were used to identify the equilibrium phases and compared well with the experimental results.
- 1 August 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 22, 153-156
Electrochemical behavior of AISI316L stainless steel parts produced by laser-based powder bed fusion process and the effect of post annealing process
- 1 August 2018
- Published by Elsevier in Additive Manufacturing
- Vol. 22, 153-156
Electrochemical behavior of AISI316L stainless steel parts produced by laser-based powder bed fusion process and the effect of post annealing process