Emine Yalman
Research Subjects
Research Interests
Emine Yalman has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Tolga Depci
Iskenderun Technical University
3 shared publications Gabriella Federer-Kovacs
2 shared publicationsHani Al Khalaf
2 shared publicationsTolga Depci
2 shared publications- Gabriella Federer Kovacsne
Department of Petroleum Engineering, Faculty of Earth Science, University of Miskolc, 3515, Miskolc, Hungary
1 shared publication - Gabriella Federer-Kovacs
University of Miskolc
1 shared publication
Latest Publications
- 13 November 2026
- Published by Iskenderun Technical University, Institute of Graduate Studies
Farklı biyokütle kaynaklarından hard karbon eldesi ile enerji depolamada uygulanabilirliği
Bu tez çalışması kapsamında doğada hazır şekilde bulunan biyokütle kaynakları olarak nar kabuğu ve nar çekirdeği ile birlikte doğada doğal, hazır olarak bulunmayan sentetik biyokütle kaynağı olarak atık itfaiye elbisesi baz alınarak iki farklı kategoride olan ilgili biyokütle kaynaklarının enerji depolama uygulamalarında kullanımı çalışılmıştır. Bu kapsamda nar kabuğu, nar çekirdeği ve atık itfaiye elbisesinden öncelikle son yıllarda oldukça güncel olan ve araştırmacıların yoğun ilgisini çeken bir konu olan hard karbon direkt karbonizasyon, çift aşamalı karbonizasyon ve hidrotermal karbonizasyon metodları ile sentezlenmiş ve karakterizasyonları yapılmıştır. Akabinde nar çekirdeği ve nar kabuğundan ürtilen hard karbonlar süper kapasitörde uygulanır iken atık itfaiye elbisesinden üretilen hard karbonlar ise ve Na-iyon bataryada elektrot malzemesi olarak çalışılarak elektrokimyasal performansları incelenmiştir. Üretilen hard karbonların uygulanan fourier dönüşümü kızılötesi spektroskopisi (FTIR), X-ışını difraksiyonu (XRD), raman spektropisi, taramalı elektron mikroskobu (SEM), Enerji Dağıtıcı X-Işını Analizi (EDX) ve Brunauer-Emmett-Teller (BET) karakterizasyon işlemleri neticesinde sentezlenen ürünlerin karbon temelli, düzensiz bir yapıya sahip olduğu görülmekle birlikte sentezlenen ürünlerin hard karbon olduğu teyit edilmiştir. Nar kabuğu ve nar çekirdeğinden üretilen hard karbonların süper kapasitör uygulamasında CV sonuçları üretilen elektrotların şarj ve deşarj kabiliyetinin olduğunu göstermekle birlikte en yüksek spesifik kapasite nar çekirdeğinden 5 mV/s tarama hızında 5,8 F/g, nar kabuğundan da yine 5 mV/s tarama hızında 11,4 F/g olarak elde edilmiştir. Na-iyon batarya uygulamasında ise öncelikle üretilen hard karbonların anot olarak kullanıldığı yarım hücre batarya oluşturulmuştur. Bu uygulamada birinci ve ikinci döngüde sırasıyla 410 ve 233 mAh g-1 kapasite değerleri edinen en yüksek kapasiteler olmuştur. Farklı sıcaklıklarda gerçekleştirilen galvonastatik döngü testleri sıcaklığın yarım hücre batarya kapasitesine doğrudan etki ettiğini göstermiştir. Ayrıca yarım hücre batarya işleminde katı elektrolit ara yüzü (SEI)'nün oluşması esnasında büyük miktarda sodyum iyonunun tüketildiği gözlenmiştir. Bu sodyum iyon kaybını telafi etmek için yarım hücre sonuçlarından en iyi performans gösteren iki hard karbon numunesi seçilerek elektrokimyasal işlemle ön sodyumlama tekniği uygulandıktan sonra Na0.67Mn0.5Fe0.45Ti0.07O2 katot olmak ve ön-sodyumlaştırılmış hard karbon numuneleri birleştirilerek tam hücreler üretilmiştir. Tam hücre testleri sonucunda en yüksek kapasite 2–4 V voltaj aralığı ve C/10 koşulları altında 114,9 mAh g-1 olarak elde edilmiştir.
- 13 November 2026
- Published by Iskenderun Technical University, Institute of Graduate Studies
Farklı biyokütle kaynaklarından hard karbon eldesi ile enerji depolamada uygulanabilirliği
Bu tez çalışması kapsamında doğada hazır şekilde bulunan biyokütle kaynakları olarak nar kabuğu ve nar çekirdeği ile birlikte doğada doğal, hazır olarak bulunmayan sentetik biyokütle kaynağı olarak atık itfaiye elbisesi baz alınarak iki farklı kategoride olan ilgili biyokütle kaynaklarının enerji depolama uygulamalarında kullanımı çalışılmıştır. Bu kapsamda nar kabuğu, nar çekirdeği ve atık itfaiye elbisesinden öncelikle son yıllarda oldukça güncel olan ve araştırmacıların yoğun ilgisini çeken bir konu olan hard karbon direkt karbonizasyon, çift aşamalı karbonizasyon ve hidrotermal karbonizasyon metodları ile sentezlenmiş ve karakterizasyonları yapılmıştır. Akabinde nar çekirdeği ve nar kabuğundan ürtilen hard karbonlar süper kapasitörde uygulanır iken atık itfaiye elbisesinden üretilen hard karbonlar ise ve Na-iyon bataryada elektrot malzemesi olarak çalışılarak elektrokimyasal performansları incelenmiştir. Üretilen hard karbonların uygulanan fourier dönüşümü kızılötesi spektroskopisi (FTIR), X-ışını difraksiyonu (XRD), raman spektropisi, taramalı elektron mikroskobu (SEM), Enerji Dağıtıcı X-Işını Analizi (EDX) ve Brunauer-Emmett-Teller (BET) karakterizasyon işlemleri neticesinde sentezlenen ürünlerin karbon temelli, düzensiz bir yapıya sahip olduğu görülmekle birlikte sentezlenen ürünlerin hard karbon olduğu teyit edilmiştir. Nar kabuğu ve nar çekirdeğinden üretilen hard karbonların süper kapasitör uygulamasında CV sonuçları üretilen elektrotların şarj ve deşarj kabiliyetinin olduğunu göstermekle birlikte en yüksek spesifik kapasite nar çekirdeğinden 5 mV/s tarama hızında 5,8 F/g, nar kabuğundan da yine 5 mV/s tarama hızında 11,4 F/g olarak elde edilmiştir. Na-iyon batarya uygulamasında ise öncelikle üretilen hard karbonların anot olarak kullanıldığı yarım hücre batarya oluşturulmuştur. Bu uygulamada birinci ve ikinci döngüde sırasıyla 410 ve 233 mAh g-1 kapasite değerleri edinen en yüksek kapasiteler olmuştur. Farklı sıcaklıklarda gerçekleştirilen galvonastatik döngü testleri sıcaklığın yarım hücre batarya kapasitesine doğrudan etki ettiğini göstermiştir. Ayrıca yarım hücre batarya işleminde katı elektrolit ara yüzü (SEI)'nün oluşması esnasında büyük miktarda sodyum iyonunun tüketildiği gözlenmiştir. Bu sodyum iyon kaybını telafi etmek için yarım hücre sonuçlarından en iyi performans gösteren iki hard karbon numunesi seçilerek elektrokimyasal işlemle ön sodyumlama tekniği uygulandıktan sonra Na0.67Mn0.5Fe0.45Ti0.07O2 katot olmak ve ön-sodyumlaştırılmış hard karbon numuneleri birleştirilerek tam hücreler üretilmiştir. Tam hücre testleri sonucunda en yüksek kapasite 2–4 V voltaj aralığı ve C/10 koşulları altında 114,9 mAh g-1 olarak elde edilmiştir.
- Open Access
- 25 December 2022
- Published by Iskenderun Technical University in Natural and Engineering Sciences
- Vol. 7 (3) , 319-324
Effect of Amorphous Silica Produced from Pumice and Quartzite on the Flow Characteristics of Drilling Mud
Various additives are introduced to drilling mud to control its flow behavior in drilling operations under the desired conditions. These additives can cause increased drilling costs and environmental damage. In recent years, natural materials have mainly been used in drilling mud to reduce the increasing costs. In this study, amorphous silica was obtained by alkaline extraction method from pumice and quartzite, having a large reserve in Turkiye. Amorphous silica, which is cost-effective and easy to supply, was used in the drilling mud and rheological and filtration tests of the fluids. The results obtained from the study indicate that drilling mud with 8, 9, and 10 % of amorphous silica exhibits promising results.
- 25 December 2022
- Published by Iskenderun Technical University in Natural and Engineering Sciences
- Vol. 7 (3) , 319-324
Open AccessEffect of Amorphous Silica Produced from Pumice and Quartzite on the Flow Characteristics of Drilling Mud
Various additives are introduced to drilling mud to control its flow behavior in drilling operations under the desired conditions. These additives can cause increased drilling costs and environmental damage. In recent years, natural materials have mainly been used in drilling mud to reduce the increasing costs. In this study, amorphous silica was obtained by alkaline extraction method from pumice and quartzite, having a large reserve in Turkiye. Amorphous silica, which is cost-effective and easy to supply, was used in the drilling mud and rheological and filtration tests of the fluids. The results obtained from the study indicate that drilling mud with 8, 9, and 10 % of amorphous silica exhibits promising results.
- Open Access
- 1 March 2022
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 210
Development of novel inhibitive water-based drilling muds for oil and gas field applications
- 1 March 2022
- Published by Elsevier in Journal of Petroleum Science and Engineering
- Vol. 210
Open AccessDevelopment of novel inhibitive water-based drilling muds for oil and gas field applications
- 1 January 2022
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 37 (2) , 13-21
Development of Water-Based Drilling Fluid in Mitigation of Differential Sticking Tendency
The objective of the study is to design a drilling fluid that prevents differential pressure pipe sticking tendency caused by drilling fluid with fly ash that is an industrial waste generated from the combustion of coal. To this end, drilling fluid samples were prepared with different particle sizes obtained through the sieving and grinding process and increasing concentrations of fly ash. Differential pipe sticking tests of the samples were performed by applying 3.447 MPa (500 psi) pressure and using a Fann Model 21150 Differential Sticking Tester in order to determine how the coefficient of sticking and torque reading varied with the fly ash. From the results, it was observed that the coefficient of sticking and torque reading of the water-based drilling fluids decreased up to a specific concentration as the concentration of fly ash increased. Furthermore, particle size analysis illustrated that the coefficient of sticking and torque of the drilling fluid differs depending on the particle size of fly ash introduced. The drilling fluid designed with ground fly ash demonstrated lower sticking coefficient and torque reading than that of drilling fluids formulated with raw and sieved fly ashes. The experimental study revealed that fly ash is a promising additive in the mitigation of differential sticking tendency caused by water-based drilling fluids.
- 1 January 2022
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 37 (2) , 13-21
Development of Water-Based Drilling Fluid in Mitigation of Differential Sticking Tendency
The objective of the study is to design a drilling fluid that prevents differential pressure pipe sticking tendency caused by drilling fluid with fly ash that is an industrial waste generated from the combustion of coal. To this end, drilling fluid samples were prepared with different particle sizes obtained through the sieving and grinding process and increasing concentrations of fly ash. Differential pipe sticking tests of the samples were performed by applying 3.447 MPa (500 psi) pressure and using a Fann Model 21150 Differential Sticking Tester in order to determine how the coefficient of sticking and torque reading varied with the fly ash. From the results, it was observed that the coefficient of sticking and torque reading of the water-based drilling fluids decreased up to a specific concentration as the concentration of fly ash increased. Furthermore, particle size analysis illustrated that the coefficient of sticking and torque of the drilling fluid differs depending on the particle size of fly ash introduced. The drilling fluid designed with ground fly ash demonstrated lower sticking coefficient and torque reading than that of drilling fluids formulated with raw and sieved fly ashes. The experimental study revealed that fly ash is a promising additive in the mitigation of differential sticking tendency caused by water-based drilling fluids.
- Open Access
- 15 December 2021
- Published by Iskenderun Technical University in Natural and Engineering Sciences
- Vol. 6 (3) , 223-236
Effect of Two Types of Fly Ash on Rheological and Filtration Properties of Water-Based Drilling Mud
In this study, the usage of class F fly ash (brown coal) and class C fly ash (lignite) with increasing concentration in water based mud mainly composed of bentonite dispersion was investigated at ambient conditions. Experimental results indicate that efficiency of the mud is significantly controlled by type of the fly ash tested and its concentrations. The results show that Class F fly ash enhanced filtration properties (filtrate loss and mud cake) of the mud and have no effect on the rheology including, yield point, viscosity whereas the class C fly ash increased the rheology parameters and degraded water loss into the formation and filer cake thickness dramatically. This study showed that class F fly ash displays superior performance than class C fly ash. Through this study, it was reveal that class F fly ash is a promising additive to improve the filtration characteristics of bentonite based drilling fluids, thereby contributing to reducing formation damage caused by drilling mud.
- 15 December 2021
- Published by Iskenderun Technical University in Natural and Engineering Sciences
- Vol. 6 (3) , 223-236
Open AccessEffect of Two Types of Fly Ash on Rheological and Filtration Properties of Water-Based Drilling Mud
In this study, the usage of class F fly ash (brown coal) and class C fly ash (lignite) with increasing concentration in water based mud mainly composed of bentonite dispersion was investigated at ambient conditions. Experimental results indicate that efficiency of the mud is significantly controlled by type of the fly ash tested and its concentrations. The results show that Class F fly ash enhanced filtration properties (filtrate loss and mud cake) of the mud and have no effect on the rheology including, yield point, viscosity whereas the class C fly ash increased the rheology parameters and degraded water loss into the formation and filer cake thickness dramatically. This study showed that class F fly ash displays superior performance than class C fly ash. Through this study, it was reveal that class F fly ash is a promising additive to improve the filtration characteristics of bentonite based drilling fluids, thereby contributing to reducing formation damage caused by drilling mud.
- 1 January 2021
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 36 (5) , 1-12
A new eco-friendly and low cost additive in water based drilling fluids
This study investigates the possibility of using rice husk ash as an additive to develop an environmentally friendly and low-cost drilling fluid system. The rice husk ash was added as an additive to water-based bentonite drilling fluids at different concentrations ranging from 2 wt% to 15 wt%. Rheological and filtration properties of each drilling fluid developed were measured by using a viscometer and standard low-pressure low-temperature filter press. Subsequently, cutting carrying index, minimum annulus velocity required to clean bottom of the well efficiently, flow behaviour index and permeability of mud cakes of the formulated systems were calculated in order to assess performance of the systems. The results demonstrated that the rheological and properties were improved depending on concentration of rice husk ash introduced. With the introduction of 15 wt% concentration of rice husk ash, while apparent viscosity and yield point increased by 60% and 183%, respectively, thixotropy and plastic viscosity decreased by 29% and 63%, respectively. On the other hand, drilling fluid with 4% wt% content of rice husk ash reduced the fluid loss by 10%. Moreover, results showed that cutting carrying index, minimum annulus velocity required to clean bottom of the well efficiently and flow behaviour index of the enhanced with the exploitation of rice husk ash in the drilling fluid. This study showed that rice husk ash as a promising additive to use in the water-based bentonite drilling fluids when properly implemented, and hence reducing the impact on the environment, and the total cost for drilling.
- 1 January 2021
- Published by Faculty of Mining, Geology and Petroleum Engineering in Rudarsko-geološko-naftni zbornik
- Vol. 36 (5) , 1-12
A new eco-friendly and low cost additive in water based drilling fluids
This study investigates the possibility of using rice husk ash as an additive to develop an environmentally friendly and low-cost drilling fluid system. The rice husk ash was added as an additive to water-based bentonite drilling fluids at different concentrations ranging from 2 wt% to 15 wt%. Rheological and filtration properties of each drilling fluid developed were measured by using a viscometer and standard low-pressure low-temperature filter press. Subsequently, cutting carrying index, minimum annulus velocity required to clean bottom of the well efficiently, flow behaviour index and permeability of mud cakes of the formulated systems were calculated in order to assess performance of the systems. The results demonstrated that the rheological and properties were improved depending on concentration of rice husk ash introduced. With the introduction of 15 wt% concentration of rice husk ash, while apparent viscosity and yield point increased by 60% and 183%, respectively, thixotropy and plastic viscosity decreased by 29% and 63%, respectively. On the other hand, drilling fluid with 4% wt% content of rice husk ash reduced the fluid loss by 10%. Moreover, results showed that cutting carrying index, minimum annulus velocity required to clean bottom of the well efficiently and flow behaviour index of the enhanced with the exploitation of rice husk ash in the drilling fluid. This study showed that rice husk ash as a promising additive to use in the water-based bentonite drilling fluids when properly implemented, and hence reducing the impact on the environment, and the total cost for drilling.