Kwangmin Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kwangmin Kim has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Junnhyeok Park
Department of Mining and Geological Engineering, University of Arizona, Tucson, USA
2 shared publications - Minkyu Kim
University of Arizona
2 shared publications - Tae-Hee Lee
University of South Carolina
2 shared publications - Yongsik Jeong
Department of Mining and Geological Engineering, University of Arizona, Tucson, USA
2 shared publications - David S. Knoff
Department of Biomedical Engineering, University of Arizona, Tucson, Arizona 85721, United States
1 shared publication John Kemeny
Mining and Geological Engineering, The University of Arizona, Tucson, USA
1 shared publication
Latest Publications
- Open Access
- 25 January 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 123 (12) , 579-588
Use of a biocompatible polymer to enhance tailings transportation and reduce water consumption at a coper-cobalt-zinc plant
Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of 'what if' studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.
- 25 January 2024
- Published by Academy of Science of South Africa in Journal of the Southern African Institute of Mining and Metallurgy
- Vol. 123 (12) , 579-588
Open AccessUse of a biocompatible polymer to enhance tailings transportation and reduce water consumption at a coper-cobalt-zinc plant
Excess water can lead to instability and even failure in tailings storage facilities (TSFs). Simply reducing the amount of water in TSFs could be the best way to ensure the safety of nearby communities. In this case study we investigated the effects of reducing the water content in tailings slurry at a copper-cobalt-zinc mine in Mexico. An environmentally friendly polymer was used as a drag reduction agent (DRA) to offset the increase in solids percentage. The potential effects of the increased solids concentration on the tailings transportation system were also assessed. A series of 'what if' studies was conducted to assess whether adding the polymer would allow the solids concentration to be increased without changing the pressure loss in the tailings pipeline. The studies entailed conducting pipe loop tests to investigate these changes under various solids/ polymer concentrations and then constructing a computational fluid dynamics (CFD) simulation model using the test results. The validated model was used to determine the optimal polymer percentages needed to maintain the same pressure loss under baseline (30% solids) conditions, and to assess the potential risks (clogging, increased erosion rates) to the pipelines. The potential water savings were found to be significant, varying from about 1.852 Mm3/a at 35% solids to 3.915 Mm3/a at 45% solids.
- 29 June 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (5) , 1475-1486
Use of an Environmentally Friendly Polymer to Reduce the Water Content in Tailings Slurry
- 29 June 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (5) , 1475-1486
Use of an Environmentally Friendly Polymer to Reduce the Water Content in Tailings Slurry
- 16 June 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (4) , 1169-1183
Estimation of Fines Generation in Blasting Using Dynamic Rock Properties and a Near-Field PPV Damage Model
- 16 June 2020
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (4) , 1169-1183
Estimation of Fines Generation in Blasting Using Dynamic Rock Properties and a Near-Field PPV Damage Model
- Open Access
- 3 December 2019
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 9 (68) , 40146-40151
Liquid amphiphilic polymer for effective airborne dust suppression
Airborne dust is a byproduct of natural and artificial occurrences, including high winds in arid regions and human activities, and it affects most of the world's population. Watering is the most general practice for reducing airborne dust by wetting the surface of the dust source to agglomerate dust particles via the capillary effect, increasing the aerodynamic diameter of (ultra)fine particles and reducing dust emission. However, the short-term effectiveness due to fast water evaporation, requiring frequent watering, is a major disadvantage. Herein, we utilized biocompatible liquid polymers as additives in water to prolong moist conditions of dust sources due to their liquid state. After the water evaporated, the liquid polymers maintained moisture on the dust sources, resulting in significantly reduced (ultra)fine particle emissions and extended effectiveness compared to conventional water treatment. Interestingly, we observed greater dust suppressive effectiveness with liquid amphiphilic polymer than liquid hydrophilic polymer because of the synergistic effect of the liquid state and amphiphilic property of the polymer. Translating lab-scale experiments to pilot-scale field-testing confirmed the potential for utilizing biocompatible liquid amphiphilic polymers to advance airborne dust suppression technology.
- 3 December 2019
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 9 (68) , 40146-40151
Open AccessLiquid amphiphilic polymer for effective airborne dust suppression
Airborne dust is a byproduct of natural and artificial occurrences, including high winds in arid regions and human activities, and it affects most of the world's population. Watering is the most general practice for reducing airborne dust by wetting the surface of the dust source to agglomerate dust particles via the capillary effect, increasing the aerodynamic diameter of (ultra)fine particles and reducing dust emission. However, the short-term effectiveness due to fast water evaporation, requiring frequent watering, is a major disadvantage. Herein, we utilized biocompatible liquid polymers as additives in water to prolong moist conditions of dust sources due to their liquid state. After the water evaporated, the liquid polymers maintained moisture on the dust sources, resulting in significantly reduced (ultra)fine particle emissions and extended effectiveness compared to conventional water treatment. Interestingly, we observed greater dust suppressive effectiveness with liquid amphiphilic polymer than liquid hydrophilic polymer because of the synergistic effect of the liquid state and amphiphilic property of the polymer. Translating lab-scale experiments to pilot-scale field-testing confirmed the potential for utilizing biocompatible liquid amphiphilic polymers to advance airborne dust suppression technology.
- 1 August 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (1) , 141-151
A Case Study: Determination of the Optimal Tailings Beach Distance as a Guideline for Safe Water Management in an Upstream TSF
- 1 August 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 37 (1) , 141-151
A Case Study: Determination of the Optimal Tailings Beach Distance as a Guideline for Safe Water Management in an Upstream TSF
- 7 May 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 36 (4) , 785-795
Tailings Storage Facilities (TSFs) Dust Control Using Biocompatible Polymers
- 7 May 2019
- Published by Springer Nature in Mining, Metallurgy & Exploration
- Vol. 36 (4) , 785-795
Tailings Storage Facilities (TSFs) Dust Control Using Biocompatible Polymers
- Top Cited Papers
- 17 December 2013
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 47 (6) , 2005-2019
Effect of Rapid Thermal Cooling on Mechanical Rock Properties
- 17 December 2013
- Published by Springer Nature in Rock Mechanics and Rock Engineering
- Vol. 47 (6) , 2005-2019
Top Cited PapersEffect of Rapid Thermal Cooling on Mechanical Rock Properties