Umair Ahmed
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Umair Ahmed has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Paavo Rasilo
Electrical Engineering Unit, Tampere University, Tampere, Finland
3 shared publications - David Blažević
Tampere Univ. (Finland)
2 shared publications M. Zucca
Istituto Nazionale di Ricerca Metrologica, INRIM, Strada delle Cacce 91, Torino, Italy
2 shared publicationsP. Rasilo
Tampere University, Electrical Engineering, P.O. Box 692, FI-33720, Tampere (Hervanta campus), Finland
2 shared publications- Stefano Palumbo
Graphene Labs Istituto Italiano di Tecnologia via Morego 30 16163 Genova Italy
2 shared publications - Yoshito Mizukawa
University of Hyogo
2 shared publications
Latest Publications
- Open Access
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (8) , 1-14
Influence of Resonant Circuits on Optimal Design of Magnetostrictive Energy Harvester in Free Vibration
This paper presents a novel modeling method for a magnetostrictive energy harvester connected to a resonant circuit. The method is based on analytical calculations coupled with experimental parameter identifications. The magnetic flux leakages from the pickup coil and the magnetostrictive material are considered. Under the assumptions of linearity and fundamental oscillation, the governing equations of the magnetostrictive energy harvester were derived from the Euler-Lagrange equations for an electromagnetic-mechanically coupled system. The energy harvesting efficiency of the harvester was obtained by solving the derived governing equations, and it can be described with five non-dimensional parameters. Among the non-dimensional parameters, the natural frequency ratio and damping ratio of the load resistance have optimal values to maximize the energy harvesting efficiency. This study derived these optimal design parameters depending on the circuit configuration and types of energy given to the harvester. In the magnetostrictive energy harvester with a series-resonant circuit subject to kinetic energy impact, these optimal design parameters can be obtained in simple algebraic forms. Experimental validations were conducted for the magnetostrictive energy harvester with a pure resistive circuit, with series- and parallel-resonant circuits, respectively to compare their energy harvesting efficiencies. While the pure resistive configuration can harvest 21 % of given mechanical energy, both series- and parallel-resonant configurations can harvest 23 %.
- 13 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 60 (8) , 1-14
Open AccessInfluence of Resonant Circuits on Optimal Design of Magnetostrictive Energy Harvester in Free Vibration
This paper presents a novel modeling method for a magnetostrictive energy harvester connected to a resonant circuit. The method is based on analytical calculations coupled with experimental parameter identifications. The magnetic flux leakages from the pickup coil and the magnetostrictive material are considered. Under the assumptions of linearity and fundamental oscillation, the governing equations of the magnetostrictive energy harvester were derived from the Euler-Lagrange equations for an electromagnetic-mechanically coupled system. The energy harvesting efficiency of the harvester was obtained by solving the derived governing equations, and it can be described with five non-dimensional parameters. Among the non-dimensional parameters, the natural frequency ratio and damping ratio of the load resistance have optimal values to maximize the energy harvesting efficiency. This study derived these optimal design parameters depending on the circuit configuration and types of energy given to the harvester. In the magnetostrictive energy harvester with a series-resonant circuit subject to kinetic energy impact, these optimal design parameters can be obtained in simple algebraic forms. Experimental validations were conducted for the magnetostrictive energy harvester with a pure resistive circuit, with series- and parallel-resonant circuits, respectively to compare their energy harvesting efficiencies. While the pure resistive configuration can harvest 21 % of given mechanical energy, both series- and parallel-resonant configurations can harvest 23 %.
- Open Access
- 6 May 2023
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 558
Modeling and efficiency maximization of magnetostrictive energy harvester under free vibration
- 6 May 2023
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 558
Open AccessModeling and efficiency maximization of magnetostrictive energy harvester under free vibration
- 24 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 57 (2) , 1-5
3-D Magneto-Mechanical Finite Element Analysis of Galfenol-Based Energy Harvester Using an Equivalent Stress Model
This paper presents the implementation of an equivalent stress model to analyze a Galfenol-based magneto-mechanical energy harvesting concept device. The equivalent stress approach can transform any arbitrary stress tensor into a uniaxial stress acting along the direction of the magnetic flux density. Unlike multiaxial magneto-mechanical phenomenological models, it offers simple implementation to predict the permeability change by interpolation from uniaxial measurements. For the first time, the proposed model is implemented in a 3D finite element solver using COMSOL Multiphysics software to analyze an energy harvesting setup, where the effect of mechanical preload and magnetic bias on the output power can be studied. The model is tested under different compressive loading cases ranging 20 – 80 MPa, and the simulated results are compared with the measurement results for validation. The results show that the approach can successfully be used as a tool to analyze the behavior of the harvester device and to determine the optimal design parameters.
- 24 July 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Magnetics
- Vol. 57 (2) , 1-5
3-D Magneto-Mechanical Finite Element Analysis of Galfenol-Based Energy Harvester Using an Equivalent Stress Model
This paper presents the implementation of an equivalent stress model to analyze a Galfenol-based magneto-mechanical energy harvesting concept device. The equivalent stress approach can transform any arbitrary stress tensor into a uniaxial stress acting along the direction of the magnetic flux density. Unlike multiaxial magneto-mechanical phenomenological models, it offers simple implementation to predict the permeability change by interpolation from uniaxial measurements. For the first time, the proposed model is implemented in a 3D finite element solver using COMSOL Multiphysics software to analyze an energy harvesting setup, where the effect of mechanical preload and magnetic bias on the output power can be studied. The model is tested under different compressive loading cases ranging 20 – 80 MPa, and the simulated results are compared with the measurement results for validation. The results show that the approach can successfully be used as a tool to analyze the behavior of the harvester device and to determine the optimal design parameters.
- 3 January 2020
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 500, 166390
Modeling a Fe-Ga energy harvester fitted with magnetic closure using 3D magneto-mechanical finite element model
- 3 January 2020
- Published by Elsevier in Journal of Magnetism and Magnetic Materials
- Vol. 500, 166390
Modeling a Fe-Ga energy harvester fitted with magnetic closure using 3D magneto-mechanical finite element model
- 27 August 2010
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 20 (7) , 1163-1170
Effect of Hot Rolling Process on Microstructure and Properties of Low-Carbon Al-Killed Steels Produced Through TSCR Technology
- 27 August 2010
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 20 (7) , 1163-1170
Effect of Hot Rolling Process on Microstructure and Properties of Low-Carbon Al-Killed Steels Produced Through TSCR Technology