Kaishu Nitta
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Kaishu Nitta has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Tsuyohito Ito
Department of Advanced Materials Science, Graduate School of Frontier Sciences, The University of Tokyo
6 shared publications - Kazuo Terashima
Department of Advanced Materials Science, Graduate School of Frontier Sciences, The University of Tokyo
5 shared publications - Yoshiki Shimizu
Research Institute of Core Technology for Materials Innovation National Institute of Advanced Industrial Science and Technology (AIST) Tsukuba Japan
4 shared publications - Hideaki Yamada
National Institute of Advanced Industrial Science and Technology
3 shared publications - Hitoshi Muneoka
Department of Advanced Materials Science, Graduate School of Frontier Sciences, The University of Tokyo
3 shared publications - Takehiro Shimaoka
Advanced Power Electronics Research Center, National Institute of Advanced Industrial Science and Technology (AIST), 1-8-31 Midorigaoka, Ikeda-shi, Osaka 563-8577, Japan
3 shared publications
Latest Publications
- 28 February 2025
- Published by Elsevier in Diamond and Related Materials
- Vol. 154
In-situ microscopic observation of single-crystal diamond during chemical vapor deposition
- 28 February 2025
- Published by Elsevier in Diamond and Related Materials
- Vol. 154
In-situ microscopic observation of single-crystal diamond during chemical vapor deposition
- 5 August 2024
- Published by Elsevier in Diamond and Related Materials
- Vol. 148
Spectroscopic analysis of pulsed-mode plasma with argon addition for diamond growth
- 5 August 2024
- Published by Elsevier in Diamond and Related Materials
- Vol. 148
Spectroscopic analysis of pulsed-mode plasma with argon addition for diamond growth
- 9 May 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (31) , 315203
Synthesis of ZnO and ZnO/Ag fine particles by plasma-assisted inkjet processing
Zinc oxide (ZnO) and its composite particles with controlled sizes, shapes, compositions, and physical and chemical properties are required for a wide variety of applications. In this study, we report a simple method for synthesising ZnO and ZnO/Ag composite particles via atmospheric-pressure plasma processing using inkjet droplets. Depending on the initial solution concentration, ZnO particles containing voids, with average sizes ranging from submicrons to several microns can be synthesised. Energy dispersive x-ray spectroscopy measurements of the synthesised ZnO/Ag particles suggest that the molar ratio of Ag to Zn in the initial solution was retained in the synthesised particles. A high surface-enhanced Raman scattering effect was observed in the particles synthesised from the solution with an Ag molar ratio of 50% to the total solute. The proposed method enables the synthesis of ZnO particles of various sizes, microstructures, compositions and optical properties with relatively narrow size distributions.
- 9 May 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 57 (31) , 315203
Synthesis of ZnO and ZnO/Ag fine particles by plasma-assisted inkjet processing
Zinc oxide (ZnO) and its composite particles with controlled sizes, shapes, compositions, and physical and chemical properties are required for a wide variety of applications. In this study, we report a simple method for synthesising ZnO and ZnO/Ag composite particles via atmospheric-pressure plasma processing using inkjet droplets. Depending on the initial solution concentration, ZnO particles containing voids, with average sizes ranging from submicrons to several microns can be synthesised. Energy dispersive x-ray spectroscopy measurements of the synthesised ZnO/Ag particles suggest that the molar ratio of Ag to Zn in the initial solution was retained in the synthesised particles. A high surface-enhanced Raman scattering effect was observed in the particles synthesised from the solution with an Ag molar ratio of 50% to the total solute. The proposed method enables the synthesis of ZnO particles of various sizes, microstructures, compositions and optical properties with relatively narrow size distributions.
- Open Access
- 12 March 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (12) , 14310-14315
Extremely Monodispersed Micrometer-Scale Spherical Particle Synthesis of Ag Inside a Microdroplet Vaporizing in Plasma
Spherical Ag particles have received considerable attention because of their unique properties as well as their applications in various fields. In the present study, the synthesis of micrometer-scale spherical Ag particles with an extremely narrow size distribution is demonstrated using a simple capacitively coupled atmospheric-pressure plasma reactor with an inkjet head. Droplets of a Ag nitrate aqueous solution are ejected from the inkjet head to synthesize Ag particles. The gaseous temperature in the reactor is adjusted such that Ag can be melted with a negligibly small vapor pressure. These particles exhibit a spherical shape with a smooth surface. The mean diameter of the particles is 0.91 ± 0.013 μm with a small coefficient of variation of 1.5%, the smallest value ever reported for Ag particles of less than 1 μm. The grain sizes of the particles are larger than 100 nm, as expected from the broadening of the X-ray diffraction peaks. The excellent monodispersity of the particles synthesized by this method may expand the applications with micrometer-scale spheres such as ball spacer, microsized ball bearing, and inks for printed electronics.
- 12 March 2024
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 9 (12) , 14310-14315
Open AccessExtremely Monodispersed Micrometer-Scale Spherical Particle Synthesis of Ag Inside a Microdroplet Vaporizing in Plasma
Spherical Ag particles have received considerable attention because of their unique properties as well as their applications in various fields. In the present study, the synthesis of micrometer-scale spherical Ag particles with an extremely narrow size distribution is demonstrated using a simple capacitively coupled atmospheric-pressure plasma reactor with an inkjet head. Droplets of a Ag nitrate aqueous solution are ejected from the inkjet head to synthesize Ag particles. The gaseous temperature in the reactor is adjusted such that Ag can be melted with a negligibly small vapor pressure. These particles exhibit a spherical shape with a smooth surface. The mean diameter of the particles is 0.91 ± 0.013 μm with a small coefficient of variation of 1.5%, the smallest value ever reported for Ag particles of less than 1 μm. The grain sizes of the particles are larger than 100 nm, as expected from the broadening of the X-ray diffraction peaks. The excellent monodispersity of the particles synthesized by this method may expand the applications with micrometer-scale spheres such as ball spacer, microsized ball bearing, and inks for printed electronics.
- Open Access
- 20 October 2023
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 44 (1) , 289-303
Highly Reproducible Synthesis of Hollow Zirconia Particles via Atmospheric-Pressure Plasma Processing with Inkjet Droplets
Hollow particles have attracted considerable attention owing to their unique properties. In this study, hollow monoclinic zirconia particles were directly synthesized from inkjet droplets of a zirconyl hydroxychloride aqueous solution via atmospheric-pressure plasma processing. Hollow structures with craggy surfaces were obtained in the plasma at gas temperatures above 1000 K. The steep solvent evaporation rate induced by the localized high-energy reaction field of the atmospheric-pressure plasma may have induced solute condensation near the droplet surface and contributed to the formation of hollow particles. The average diameter of the synthesized particles was ~ 3 μm, while their size distribution was narrow (coefficient of variation: 0.06–0.10). The high reproducibility of the synthesized particles was attributed to the small variations in inkjet droplet size. The proposed method enables the rapid synthesis of hollow particles of various inorganic materials, while controlling their number and composition.
- 20 October 2023
- Published by Springer Nature in Plasma Chemistry and Plasma Processing
- Vol. 44 (1) , 289-303
Open AccessHighly Reproducible Synthesis of Hollow Zirconia Particles via Atmospheric-Pressure Plasma Processing with Inkjet Droplets
Hollow particles have attracted considerable attention owing to their unique properties. In this study, hollow monoclinic zirconia particles were directly synthesized from inkjet droplets of a zirconyl hydroxychloride aqueous solution via atmospheric-pressure plasma processing. Hollow structures with craggy surfaces were obtained in the plasma at gas temperatures above 1000 K. The steep solvent evaporation rate induced by the localized high-energy reaction field of the atmospheric-pressure plasma may have induced solute condensation near the droplet surface and contributed to the formation of hollow particles. The average diameter of the synthesized particles was ~ 3 μm, while their size distribution was narrow (coefficient of variation: 0.06–0.10). The high reproducibility of the synthesized particles was attributed to the small variations in inkjet droplet size. The proposed method enables the rapid synthesis of hollow particles of various inorganic materials, while controlling their number and composition.
- 1 May 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (5) , 055008
Evaporation behavior of liquid microdroplets in atmospheric-pressure nonequilibrium plasma
In recent years, atmospheric-pressure nonequilibrium plasma processing using microdroplets has attracted significant attention. To improve the controllability of this process, an understanding of the evaporation behavior of droplets in plasma is highly desirable. In this study, we examine the evaporation behavior of well-controlled inkjet droplets in atmospheric-pressure nonequilibrium argon plasma through both experiments and modeling. A comparison of the droplet evaporation model based on energy balance considering gas temperature, electron and ion collisions, and recombination reactions with experimental evaporation behavior suggests that droplet evaporation is enhanced in high-density plasma environments with electron and ion densities exceeding 1019 m−3 when compared with that in non-ionized gaseous environments at a gas temperature below 1000 K.
- 1 May 2023
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 32 (5) , 055008
Evaporation behavior of liquid microdroplets in atmospheric-pressure nonequilibrium plasma
In recent years, atmospheric-pressure nonequilibrium plasma processing using microdroplets has attracted significant attention. To improve the controllability of this process, an understanding of the evaporation behavior of droplets in plasma is highly desirable. In this study, we examine the evaporation behavior of well-controlled inkjet droplets in atmospheric-pressure nonequilibrium argon plasma through both experiments and modeling. A comparison of the droplet evaporation model based on energy balance considering gas temperature, electron and ion collisions, and recombination reactions with experimental evaporation behavior suggests that droplet evaporation is enhanced in high-density plasma environments with electron and ion densities exceeding 1019 m−3 when compared with that in non-ionized gaseous environments at a gas temperature below 1000 K.
- 3 June 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (33) , 33LT01
Plasma-assisted synthesis of size-controlled monodisperse submicron gold particles using inkjet droplets
In this study, we synthesized gold spheroidized particles with sub-micrometer diameters via atmospheric-pressure plasma-assisted processing with inkjet droplets. Microdroplets of chloroauric acid (HAuCl 4 ) solution were generated by an inkjet device with high reproducibility and exposed to radio frequency plasma. The synthesized sub-micrometer gold particles have a very narrow size distribution (3%–9% standard deviation), and their diameters can be controlled in the 0.3–0.6 μ m range by adjusting the concentration of the solution.
- 3 June 2021
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 54 (33) , 33LT01
Plasma-assisted synthesis of size-controlled monodisperse submicron gold particles using inkjet droplets
In this study, we synthesized gold spheroidized particles with sub-micrometer diameters via atmospheric-pressure plasma-assisted processing with inkjet droplets. Microdroplets of chloroauric acid (HAuCl 4 ) solution were generated by an inkjet device with high reproducibility and exposed to radio frequency plasma. The synthesized sub-micrometer gold particles have a very narrow size distribution (3%–9% standard deviation), and their diameters can be controlled in the 0.3–0.6 μ m range by adjusting the concentration of the solution.
- 28 May 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (31) , 315202
Printing PEDOT from EDOT via plasma-assisted inkjet printing
We demonstrate the simultaneous polymerization of 3,4-ethylenedioxythiophene (EDOT) monomer stock solution ink and printing of the resulting poly(3,4-ethylenedioxythiophene) (PEDOT) via plasma-assisted inkjet printing. The plasma-induced polymerization of EDOT is confirmed via Raman and Fourier-transform infrared (FT-IR) spectroscopies of the printed line. Furthermore, we also achieve plasma-induced polymerization of PEDOT with poly(styrenesulfonate) (PSS) for the synthesis of an electrically conductive film from EDOT. Consequently, we fabricate a PEDOT/PSS film with conductivity of the order of 10 −2 Scm −1 on a borosilicate glass substrate. Our approach achieves (i) direct patterning with PEDOT polymerization and (ii) doping with PEDOT polymerization as separate processes, and our results suggest that on-site printing of conductive PEDOT/PSS with polymerization is possible through the use of an inkjet system with resistance to even the strong acidity of PSS.
- 28 May 2019
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 52 (31) , 315202
Printing PEDOT from EDOT via plasma-assisted inkjet printing
We demonstrate the simultaneous polymerization of 3,4-ethylenedioxythiophene (EDOT) monomer stock solution ink and printing of the resulting poly(3,4-ethylenedioxythiophene) (PEDOT) via plasma-assisted inkjet printing. The plasma-induced polymerization of EDOT is confirmed via Raman and Fourier-transform infrared (FT-IR) spectroscopies of the printed line. Furthermore, we also achieve plasma-induced polymerization of PEDOT with poly(styrenesulfonate) (PSS) for the synthesis of an electrically conductive film from EDOT. Consequently, we fabricate a PEDOT/PSS film with conductivity of the order of 10 −2 Scm −1 on a borosilicate glass substrate. Our approach achieves (i) direct patterning with PEDOT polymerization and (ii) doping with PEDOT polymerization as separate processes, and our results suggest that on-site printing of conductive PEDOT/PSS with polymerization is possible through the use of an inkjet system with resistance to even the strong acidity of PSS.