Piotr Kasza

Enhanced oil recovery (EOR) can significantly contribute to sustainable energy by improving oil recovery efficiency, integrating renewable technologies, and reducing the environmental impact of extraction. This study builds on previous work involving polyfraction nanoemulsions by introducing more realistic experimental conditions using live crude oil and undiluted reservoir water. The base fluid, modified with nanoemulsion and polymer additives, was injected using an alternating strategy with varying concentrations. The most effective sequence involved reservoir water with 2 wt% nanoemulsion and 0.5 wt% polymer, followed by injections with 0.3% and 0.1% polymer. This method achieved a displacement efficiency of 68.2%, with oil recovery 21.2% higher than that obtained when using reservoir water with 0.2% of polymer with nanoemulsion. These results highlight the potential of polyfraction nanoemulsions to enhance EOR efficiency while supporting sustainable development goals.

In hot dry rocks (HDRs), hydraulic fracturing is necessary to create enhanced geothermal systems (EGSs) and optimize flow rates between injection and production wells. The geometry of the induced fracture is related to numerous factors, including rock mechanical properties, especially Young’s modulus and Poisson’s ratio. In this paper, we show the influence of Young’s and Poisson’s parameters on fracture geometry in selected HDR-type prospective areas in Poland. Parameters were determined in the laboratory based on drill core samples from granite and sandstone formations using both dynamic and static methods. The results obtained reveal strong differences between dynamic and static values in granite and less diverse results in sandstone. Based on these data, numerical simulations of fracture geometry were carried out, taking into account the variability in the rocks’ elastic parameters. Sensitivity analysis showed that relatively high diversity in the elastic parameters led to a relatively slight impact on the fracture geometry of the tested formations. The influence of Young’s modulus did not exceed 6.5% of the reference half-length and width values for sandstone and 7.3% of the half-length for granite. Variability in the fracture width was significant in granite formation and amounted to 46.4%. The influence of Poisson’s ratio was marginal in both tested types of rocks. The research results, which have not been reported previously, can be considered for the design of hydraulic fracturing operations in enhanced geothermal systems in Poland.

Dynamic elastic properties, petrophysical parameters and brittleness of hot dry rocks from prospective areas of Central Europe

The beginning of 2022 was a time of major changes in the perception of energy availability and security in European countries. The aggression of Russia against Ukraine destabilizing the European energy economy, combined with the withdrawal from fossil fuels which has been going on for a dozen years, has strengthened activities to introduce new energy technologies based on renewable energy sources. One of the most promising and stable sources of renewable energy is geothermal energy, in particular enhanced geothermal systems (EGS) in hot dry rocks (HDR). These deposits occur at a great depth in almost every place on Earth, but due to their low permeability, they require hydraulic fracturing, which results in high investment costs. This technology has been developed for several decades. The current situation in Europe seems to confirm that its rapid development to a level that guarantees stable and profitable operation is crucial. This is of particular importance in the case of former member states of the economic zone of the Council for Mutual Economic Assistance, which until recently were heavily dependent on Russian energy. This review, based on the latest available data, covers potential HDR prospective areas in the countries of the south-eastern Baltic basin, including Lithuania, Latvia, Estonia and Poland. It is specific to this region that the original heat flux density is lower as a result of the paleoclimatic effect associated with the youngest ice age; however, thermal conditions do not deviate too much compared to western Europe, especially Rhine Graben, and significantly exceed the conditions of Finland, where an EGS project is currently being operated. In Lithuania, the most prospective area is the ZNI intrusion (south of Klaipeda), characterized by a geothermal gradient of up to 40 °C/1000 m. In addition, the Precambrian batholith south of Liepāja (Latvia) and the Rapakivi granites in the north and center of Estonia are promising EGS sites. Poland has relatively the most explored EGS potential, in both volcanic, crystalline and sedimentary rocks, especially in the area of the Szczecin Trough, Gorzów Block, Moglino-Łódź Trough and Karkonosze Mountains. Unfortunately, local tectonic conditions, in particular the development of faults and natural fracture zones that affect the directions of fracture propagation during hydraulic fracturing, have not been sufficiently recognized, which is one of the main barriers to the expansion of EGS pilot projects in these countries. These issues present challenges for the researchers, especially in terms of petrophysical analyses of rocks in target zones and local stress conditions, which have a key impact on fracturing operations and profitability of the systems. Despite high investment costs on the one hand and a significant slowdown in the global economy in 2022 on the other, it remains hopeful that the authorities of individual countries will decide to accelerate research work, leading to the implementation of pilot projects of EGS installations, and that this technology will be further improved to ensure a stable clean energy supply.

The Young’s modulus and Poisson’s ratio, parameters reflecting the elastic response of a rock to stress, are the key parameters used in many engineering activities, such as hard coal mining and natural gas extraction. The objective of this paper was to present the results of complex laboratory measurements of the static and dynamic Young’s modulus and Poisson’s ratio for Upper Carboniferous hard coals from the Upper Silesian Coal Basin. The coals differed in geologic age (Mudstone Series—younger coals; Upper Silesian Sandstone Series—older coals) and petrographic structure (vitrain, clarain, and durain lithotype). Elastic parameters of the coals were determined following compression tests under a complex state of stress, as well as using the ultrasonic method in reservoir conditions. On this basis, linear functional dependences between parameters such as UCS, differential stress, confining pressure, strain rate, P- and S-wave velocities, and the static and dynamic Young’s modulus and Poisson’s ratio were determined. These dependences turned out to be linear, with strong and very strong correlation, as indicated by the high coefficients of determination, R². These new results significantly broaden the knowledge of elastic properties of Carboniferous hard coals, especially in the field of geoengineering, underground coal gasification, and reservoir stimulation for coal bed methane extraction.

Hydraulic fracturing (HF) is a well-known stimulation method used to increase production from conventional and unconventional hydrocarbon reservoirs. In recent years, HF has been widely used in Enhanced Geothermal Systems (EGS). HF in EGS is used to create a geothermal collector in impermeable or poor-permeable hot rocks (HDR) at a depth formation. Artificially created fracture network in the collector allows for force the flow of technological fluid in a loop between at least two wells (injector and producer). Fluid heats up in the collector, then is pumped to the surface. Thermal energy is used to drive turbines generating electricity. This paper is a compilation of selected data from 10 major world’s EGS projects and provides an overview of the basic elements needed to design HF. Authors were focused on two types of data: geological, i.e., stratigraphy, lithology, target zone deposition depth and temperature; geophysical, i.e., the tectonic regime at the site, magnitudes of the principal stresses, elastic parameters of rocks and the seismic velocities. For each of the EGS areas, the scope of work related to HF processes was briefly presented. The most important HF parameters are cited, i.e., fracturing pressure, pumping rate and used fracking fluids and proppants. In a few cases, the dimensions of the modeled or created hydraulic fractures are also provided. Additionally, the current state of the conceptual work of EGS projects in Poland is also briefly presented.

In the case of fracturing of the reservoirs using fracturing fluids, the size of damage to the proppant conductivity caused by treatment fluids is significant, which greatly influence the effective execution of hydraulic fracturing operations. The fracturing fluid should be characterized by the minimum damage to the conductivity of a fracture filled with proppant. A laboratory research procedure has been developed to study the damage effect caused by foamed and non-foamed fracturing fluids in the fractures filled with proppant material. The paper discusses the results for high quality foamed guar-based linear gels, which is an innovative aspect of the work compared to the non-foamed frac described in most of the studies and simulations. The tests were performed for the fracturing fluid based on a linear polymer (HPG—hydroxypropyl guar, in liquid and powder form). The rheology of nitrogen foamed-based fracturing fluids (FF) with a quality of 70% was investigated. The quartz sand and ceramic light proppant LCP proppant was placed between two Ohio sandstone rock slabs and subjected to a given compressive stress of 4000–6000 psi, at a temperature of 60 °C for 5 h. A significant reduction in damage to the quartz proppant was observed for the foamed fluid compared to that damaged by the 7.5 L/m³ natural polymer-based non-foamed linear fluid. The damage was 72.3% for the non-foamed fluid and 31.5% for the 70% foamed fluid, which are superior to the guar gum non-foamed fracturing fluid system. For tests based on a polymer concentration of 4.88 g/L, the damage to the fracture conductivity by the non-foamed fluid was 64.8%, and 26.3% for the foamed fluid. These results lead to the conclusion that foamed fluids could damage the fracture filled with proppant much less during hydraulic fracturing treatment. At the same time, when using foamed fluids, the viscosity coefficient increases a few times compared to the use of non-foamed fluids, which is necessary for proppant carrying capacities and properly conducted stimulation treatment. The research results can be beneficial for optimizing the type and performance of fracturing fluid for hydraulic fracturing in tight gas formations.

This paper presents laboratory studies based on which a stimulation technology for an oil field located in the Zechstein Main Dolomite was investigated. A large number of oil wells in the Main Dolomite produce significant amounts of reservoir water. Matrix acidizing using conventional acid solutions in such wells has caused a significant increase in water cut, because of their affinity for water. The purpose of this cooperation between the Oil and Gas Institute–NRI and the Brenntag Polska was to develop an acid treatment technology that would not increase the water cut after acidizing treatment in wells where oil production is accompanied by the production of reservoir water. Therefore, a series of tests were performed, including the selection of a suitable viscoelastic surfactant that was sensitive to crude oil. The contact of the gel of the viscoelastic surfactant fluid with crude oil resulted in the reduction of its viscosity The tests described herein include dissolution/dispersion tests, rheological tests, acid sludge tests, compatibility tests, core flow experiments, and corrosion tests, which allowed recipes to be developed for the preflush, diverter, and acidizing liquid. Then, recommendations were established for using these liquids in matrix acid treatment. A series of treatments performed according to this technology allowed the removal of near-wellbore damage without increasing the water cut.

Nanoemulsions and polymers are widely used for increasing the efficiency of enhanced oil recovery (EOR) processes. The application of both these additives enables the synergistic use of several physical phenomena that are crucial to the process. One of the methods used for assessing these processes is laboratory core flooding tests using natural cores. In various experiments, carbonate rocks are subjected to oil displacement under high pressure and temperature. Polymer solutions and a newly developed polyfraction nanoemulsion are tested. The test results confirm the usefulness of these products for EOR processes and demonstrate their stability under high pressure, high temperature, and in the presence of H₂S. Under these conditions the polymers maintain high efficiency in displacing crude oil from carbonate rocks, while the tested nanoemulsion improves the wettability of carbonate rocks and reduces interfacial tension, factors which increase the efficiency of oil displacement.The best result in the laboratory EOR simulation was obtained for polymer and nanoemulsion concentrations in dilute reservoir water of 0.05% and 1%, respectively. In this case, the measured oil recovery was 37.5% higher than that obtained when using water without additives.

Hydraulic fracturing is a well-known stimulation technique for creating fractures in a subsurface formation to achieve profitable production rates in low-permeability reservoirs. Slickwater has been widely used as a traditional fracturing fluid. However, it has multiple disadvantages, such as high consumption of water, clay swelling and low flowback recovery. Foam, as an alternative fracturing fluid, consumes less liquid and provides additional energy. However, foam bubbles are typically unstable due to the degradation of surfactants, particularly in high temperature reservoirs, which reduces their capabilities of carrying and placing proppants into fractures. The purpose of this study is to provide general guidelines for an optimised application of polymers to improve the foam stability in high temperature reservoirs while increasing the proppant placement and water usage efficiencies. In this paper, the effects of natural hydroxypropyl guar (HPG) and synthetic polyacrylamide (PAM) polymers on the rheological properties of nitrogen foam-based fluids were examined by laboratory experiments conducted using temperatures up to 110°C. Then, a 3D hydraulic fracture propagation model was developed to study the fracturing performance of HPG-foamed and PAM-foamed fluids in the Toolachee Formation, Cooper Basin. It was found that synthetic PAM polymers were more effective than natural HPG polymers in stabilising foam viscosity under high temperature conditions. The simulation results indicate that foam-based fluids totally outperform slickwater in the field case application. This paper emphasises the significance of crosslinkers, foam quality and thermal stability on the performance of foams in high temperature environments.