Peilei Zhou

For strengthening sustainability of subgrade life-cycle service performance and storing industry solid wastes in seasonally frozen regions, compared to previous research of modified silty clay (MC) which consisted of oil shale ash (OSA), fly ash (FA), and silty clay (SC), we identified for the first time, the variations in the thermal insulation capability of MC with different levels of dry density and moisture content. Taking into consideration the effects of 0–20 freeze-thaw (F-T) cycles by a laboratory test, and by the numerical simulation of coupling moisture-temperature, while considering the effects of F-T cycles, the thermal insulation capability of the MC board and the XPS board were studied quantitatively. The testing results show that the thermal conductivity of MC and SC gradually decreases as the number of F-T cycles increases, and that of the XPS board increases with the increased number of F-T cycles, and tend to be of a constant value of 0.061 W/m/K after 17 F-T cycles. The specific heat capacity of the solid particles of the MC, SC, and XPS board does not change regularly as their moisture content, and the number of F-T cycles change, and their variations are in the range of the test error (2%). Simulation results show that MC has the advantage of the thermal insulation property to reduce the frost-depth of 0.21 m, and the thermal insulation property of the composite layer consisting of the MC and XPS board is greater to reduce the frost-depth of 0.55 m, so that it can protect both the SC and sand gravel of the experimental road from the frost heave damage. The research methods and results are very significant in accurately evaluating the thermal insulation capacity and the sustainability of MC and the composite layer consisting of the MC and XPS board, strengthening the stability of the subgrade and increasing the availability of industrial waste.

Superpave gyratory compaction (SGC) and Marshall compaction methods are essentially designed according to volumetric properties. In spite of the similarity, the optimum asphalt contents (OAC) of the two methods are greatly affected by the laboratory compaction process, which would further influence their performance. This study aims to evaluate the performance of styrene-butadiene-styrene (SBS)-modified stone mastic asphalt (SMA) with basalt fiber by using SGC and Marshall compaction methods. Basalt fiber was proved to improve and strength the basic properties of SBS-asphalt according to test results of asphalt binder. The effects of SGC and Marshall compaction methods on OAC and volumetric properties, i.e., density, air voids (VA), voids in mineral aggregates (VMA), and voids filled with asphalt (VFA), were evaluated in detail. Finally, the pavement performance of asphalt mixture prepared by SGC and Marshall compaction methods were compared in order to analyze the high-temperature creep, low-temperature splitting, and moisture stability performance. Results showed that the OAC of SGC (~5.70%) was slightly lower than that of Marshall method (5.80%). Furthermore, the pavement performance of SGC specimens were improved to a certain extent compared with Marshall specimens, indicating that SGC has a better compaction effect and mechanical performance.

This study focuses on improving the performance of asphalt mixture at low- and high- temperature and analyzing the effect of diatomite and basalt fiber on the performance of the asphalt mixture. Based on the L₁₆(4⁵) orthogonal experimental design (OED), the content of diatomite (D) and basalt fiber (B) and the asphalt-aggregate (A) ratio were selected as contributing factors, and each contributing factor corresponded to four levels. Bulk volume density (γ_f), volume of air voids (VV), voids filled with asphalt (VFA), Marshall stability (MS) and splitting strength at −10 °C (S_b) were taken as the evaluation indexes. According to the results of the orthogonal experiment, the range analysis and variance analysis were used to study the effect of the diatomite content, basalt fiber content and asphalt-aggregate ratio on the performance of the asphalt mixture, and the grey correlation grade analysis (GCGA) was used to obtain the optimal mixing scheme. Furthermore, the performance tests were conducted to evaluate the performance improvement of asphalt mixtures with diatomite and basalt fibers, and the scanning electron microscopy (SEM) tests were carried out to analyze the mechanism of diatomite and basalt fibers in asphalt mixtures. The results revealed that the addition of diatomite and basalt fiber can significantly increase the VV of asphalt mixture, and reduce γ_f and VFA; the optimal performance of the asphalt mixture at high- and low-temperature are achieved with 14% diatomite, 0.32% basalt fibers and 5.45% asphalt-aggregate ratio. Moreover, the porous structure of diatomite and the overlapping network of basalt fibers are the main reasons for improving the performance of asphalt mixture.