Vasyl Kukharchuk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Vasyl Kukharchuk has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Samoil Katsyv
Vinnytsia National Technical University
4 shared publications - Valerii Hraniak
Vinnytsia National Agrarian University
3 shared publications - Volodymyr Holodiuk
Vinnytsia National Technical University
3 shared publications - Oleksandr Vasilevskyi
The University of Texas at Austin
2 shared publications - Roman Trishch
Національний аерокосмічний університет «Харківський авіаційний інститут», Ukraine
2 shared publications - Volodymyr Kucheruk
Uman National University of Horticulture
2 shared publications
Latest Publications
- Open Access
- 5 March 2026
- Published by Khmelnytskyi National University in Measuring and computing devices in technological processes
- No. 1,p. 137-144
CONDITIONS FOR REPRODUCING POWER CONSUMPTION IN ELECTRICAL NETWORKS
The article defines the conditions under which continuous current control of electrical power consumption in large, branched high-voltage electrical networks is possible. The fact is that for complete hardware current continuous control of electrical power consumption, it is necessary to have active and reactive power sensors at each node of the electrical network (at each substation) and their connection with dispatching control centers. For countries with large distances between grid nodes and control centers, this requires huge capital expenditures. Therefore, it is much more expedient to place power and voltage sensors in separate nodes and then calculate the remaining nodes using Kirchhoff's laws. Under these conditions, the system of equations using the nodal potential method becomes non-canonical, that is, the known parameters in it are part of the nodal currents and part of the nodal potentials. Such a system does not always have a unique solution, and it depends on the correct placement of power and voltage sensors. But the placement of sensors must be carried out before calculations, therefore the task of determining the conditions for correct placement of sensors without preliminary calculations is relevant, which is considered in the article.
- 5 March 2026
- Published by Khmelnytskyi National University in Measuring and computing devices in technological processes
- No. 1,p. 137-144
Open AccessCONDITIONS FOR REPRODUCING POWER CONSUMPTION IN ELECTRICAL NETWORKS
The article defines the conditions under which continuous current control of electrical power consumption in large, branched high-voltage electrical networks is possible. The fact is that for complete hardware current continuous control of electrical power consumption, it is necessary to have active and reactive power sensors at each node of the electrical network (at each substation) and their connection with dispatching control centers. For countries with large distances between grid nodes and control centers, this requires huge capital expenditures. Therefore, it is much more expedient to place power and voltage sensors in separate nodes and then calculate the remaining nodes using Kirchhoff's laws. Under these conditions, the system of equations using the nodal potential method becomes non-canonical, that is, the known parameters in it are part of the nodal currents and part of the nodal potentials. Such a system does not always have a unique solution, and it depends on the correct placement of power and voltage sensors. But the placement of sensors must be carried out before calculations, therefore the task of determining the conditions for correct placement of sensors without preliminary calculations is relevant, which is considered in the article.
- 7 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Peculiarities of Voltage Quality Control in Power Supply and Lighting Systems of Cities
This paper investigates the peculiarities of voltage quality regulation in urban power supply and street lighting systems. The paper analyzes the problems associated with voltage deviations that lead to significant production losses and consumer losses. The necessity of improving the methodology for managing voltage modes, taking into account the probabilistic nature of load changes, the multi-criteria nature of the task, decentralization of the placement of control equipment and automation of processes is considered. The expediency of using electronically controlled voltage-adding transformers as effective devices for voltage regulation in urban distribution networks is substantiated. The study delves into the principles governing the modeling of parameters and operational modes of voltage-boosting transformers, considering the nonlinearity inherent in magnetic systems and electronic components. It proposes methods to enhance the precision of calculations regarding the parameters of such transformers, aiming to secure their dependable and cost-effective functionality. Additionally, it provides instances showcasing the effective deployment of automated power consumption management systems, which leverage voltage-boosting transformers.
- 7 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 1-6
Peculiarities of Voltage Quality Control in Power Supply and Lighting Systems of Cities
This paper investigates the peculiarities of voltage quality regulation in urban power supply and street lighting systems. The paper analyzes the problems associated with voltage deviations that lead to significant production losses and consumer losses. The necessity of improving the methodology for managing voltage modes, taking into account the probabilistic nature of load changes, the multi-criteria nature of the task, decentralization of the placement of control equipment and automation of processes is considered. The expediency of using electronically controlled voltage-adding transformers as effective devices for voltage regulation in urban distribution networks is substantiated. The study delves into the principles governing the modeling of parameters and operational modes of voltage-boosting transformers, considering the nonlinearity inherent in magnetic systems and electronic components. It proposes methods to enhance the precision of calculations regarding the parameters of such transformers, aiming to secure their dependable and cost-effective functionality. Additionally, it provides instances showcasing the effective deployment of automated power consumption management systems, which leverage voltage-boosting transformers.
- 2 October 2024
- Published by Springer Nature
- p. 259-269
Adaptive Algorithms for Quantization Error Normalization of Digital Encoder-Based Tachometers
- 2 October 2024
- Published by Springer Nature
- p. 259-269
Adaptive Algorithms for Quantization Error Normalization of Digital Encoder-Based Tachometers
- Open Access
- 30 September 2022
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 12 (3) , 20-26
FEATURES OF THE ANGULAR SPEED DYNAMIC MEASUREMENTS WITH THE USE OF AN ENCODER
Based on the most significant features of the angular velocity dynamic measurements selected by the authors, the main phases of measuring information transformation were established, which allowed to obtain new mathematical models in the form of transformation function, equations for estimating quantization errors, analytical dependences for measuring range that are initial for modeling physical processes occurring in such digital measuring channels with microprocessor control. The process of converting an analog quantity into a binary code is analytically described, an equation for estimating the absolute and relative quantization error is obtained and a measurement range is established, which provides a normalized value of relative quantization error for angular velocity measuring channels with encoder. For the first time, the equation of sampling error was obtained, and it was proved that the limiting factor of the angular velocity measurements upper limit is not only the normalized value of quantization error, as previously thought, but also the value of sampling frequency fD. Therefore, to expand the measurement range (by increasing the upper limit of measurement), it is proposed not only to increase the speed of analog-to-digital conversion hardware, but also to reduce the execution time of software drivers for transmitting measurement information to RAM of microprocessor system. For this purpose, the analytical dependences of estimating the upper limit of measurement based on the value of the sampling step for different modes of measurement information transmission are obtained. The practical implementation of the software mode measurement information transmission is characterized by a minimum of hardware costs and maximum execution time of the software driver, which explains its low speed, and therefore provides a minimum value of the upper limit measurement. In the interrupt mode, the upper limit value of the angular velocity measurement is higher than in the program mode due to the reduction of the software driver’s execution time (tFl = 0). The maximum value of the angular velocity measurements upper limit can be achieved using the measurement information transmission in the mode of direct access to memory (DMA) by providing maximum speed in this mode (tFl = 0, tDR = 0). In addition, the application of the results obtained in the work allows at the design stage (during physical and mathematical modeling) to assess the basic metrological characteristics of the measuring channel, aimed at reducing the development time and debugging of hardware, software, and standardization of their metrological characteristics.
- 30 September 2022
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 12 (3) , 20-26
Open AccessFEATURES OF THE ANGULAR SPEED DYNAMIC MEASUREMENTS WITH THE USE OF AN ENCODER
Based on the most significant features of the angular velocity dynamic measurements selected by the authors, the main phases of measuring information transformation were established, which allowed to obtain new mathematical models in the form of transformation function, equations for estimating quantization errors, analytical dependences for measuring range that are initial for modeling physical processes occurring in such digital measuring channels with microprocessor control. The process of converting an analog quantity into a binary code is analytically described, an equation for estimating the absolute and relative quantization error is obtained and a measurement range is established, which provides a normalized value of relative quantization error for angular velocity measuring channels with encoder. For the first time, the equation of sampling error was obtained, and it was proved that the limiting factor of the angular velocity measurements upper limit is not only the normalized value of quantization error, as previously thought, but also the value of sampling frequency fD. Therefore, to expand the measurement range (by increasing the upper limit of measurement), it is proposed not only to increase the speed of analog-to-digital conversion hardware, but also to reduce the execution time of software drivers for transmitting measurement information to RAM of microprocessor system. For this purpose, the analytical dependences of estimating the upper limit of measurement based on the value of the sampling step for different modes of measurement information transmission are obtained. The practical implementation of the software mode measurement information transmission is characterized by a minimum of hardware costs and maximum execution time of the software driver, which explains its low speed, and therefore provides a minimum value of the upper limit measurement. In the interrupt mode, the upper limit value of the angular velocity measurement is higher than in the program mode due to the reduction of the software driver’s execution time (tFl = 0). The maximum value of the angular velocity measurements upper limit can be achieved using the measurement information transmission in the mode of direct access to memory (DMA) by providing maximum speed in this mode (tFl = 0, tDR = 0). In addition, the application of the results obtained in the work allows at the design stage (during physical and mathematical modeling) to assess the basic metrological characteristics of the measuring channel, aimed at reducing the development time and debugging of hardware, software, and standardization of their metrological characteristics.
- Open Access
- 30 September 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (3) , 82-85
TORQUE MEASURING CHANNELS: DYNAMIC AND STATIC METROLOGICAL CHARACTERISTICS
A formalized method for obtaining the analytical dependencies for the evaluation of the main dynamic and static metrological characteristics of a torque measuring channel with a capacitance sensor operating under the regulation of a microcontroller is proposed. The static and dynamic characteristics of such a typical torque measuring channel based on a capacitance force sensor were evaluated.
- 30 September 2020
- Published by Politechnika Lubelska in Informatyka, Automatyka, Pomiary w Gospodarce i Ochronie Środowiska
- Vol. 10 (3) , 82-85
Open AccessTORQUE MEASURING CHANNELS: DYNAMIC AND STATIC METROLOGICAL CHARACTERISTICS
A formalized method for obtaining the analytical dependencies for the evaluation of the main dynamic and static metrological characteristics of a torque measuring channel with a capacitance sensor operating under the regulation of a microcontroller is proposed. The static and dynamic characteristics of such a typical torque measuring channel based on a capacitance force sensor were evaluated.
- Open Access
- 30 September 2019
- Published by Karagandy University of the name of academician E.A. Buketov in Bulletin of the Karaganda University "Physics Series"
- Vol. 95 (3) , 43-51
Conditions for «deterministic chaos» phenomenon occurrence in a non-linear rl-diode electric circuit of sinusoid current
- 30 September 2019
- Published by Karagandy University of the name of academician E.A. Buketov in Bulletin of the Karaganda University "Physics Series"
- Vol. 95 (3) , 43-51
Open AccessConditions for «deterministic chaos» phenomenon occurrence in a non-linear rl-diode electric circuit of sinusoid current
- Open Access
- 28 September 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10031, 100312F-100312F-6
Noncontact method of temperature measurement based on the phenomenon of the luminophor temperature decreasing
- 28 September 2016
- Published by SPIE-Intl Soc Optical Eng
- Vol. 10031, 100312F-100312F-6
Open AccessNoncontact method of temperature measurement based on the phenomenon of the luminophor temperature decreasing