Amran Al-Ashouri
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Amran Al-Ashouri has a total of 285 co-authors. Here are the top co-authors by number of shared publications:
- Steve Albrecht
Solar Energy Division Helmholtz‐Zentrum Berlin für Materialien und Energie GmbH Berlin Germany
20 shared publications - Rutger Schlatmann
Institute Competence Centre Photovoltaics Berlin, Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Schwarzschildstrasse 3, 12489 Berlin, Germany
11 shared publications - Eike Köhnen
Solar Energy Division, Helmholtz-Zentrum Berlin, Berlin, 12489, Germany
9 shared publications - Lars Korte
Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Division Solar Energy, Kekuléstraße 5, 12489 Berlin, Germany
9 shared publications - Artiom Magomedov
Department of Organic Chemistry, Kaunas University of Technology, Radvilenu pl. 19, Kaunas, 50254, Lithuania
8 shared publications - Bernd Rech
Helmholtz‐Zentrum Berlin für Materialien und Energie GmbH Scientific Management Hahn‐Meitner‐Platz 1 14109 Berlin Germany
8 shared publications
Latest Publications
- Open Access
- 30 October 2024
- Published by Springer Nature in Nature Energy
- Vol. 10 (1) , 66-76
The impact of interfacial quality and nanoscale performance disorder on the stability of alloyed perovskite solar cells
Microscopy provides a proxy for assessing the operation of perovskite solar cells, yet most works in the literature have focused on bare perovskite thin films, missing charge transport and recombination losses present in full devices. Here we demonstrate a multimodal operando microscopy toolkit to measure and spatially correlate nanoscale charge transport losses, recombination losses and chemical composition. By applying this toolkit to the same scan areas of state-of-the-art, alloyed perovskite cells before and after extended operation, we show that devices with the highest macroscopic performance have the lowest initial performance spatial heterogeneity—a crucial link that is missed in conventional microscopy. We show that engineering stable interfaces is critical to achieving robust devices. Once the interfaces are stabilized, we show that compositional engineering to homogenize charge extraction and to minimize variations in local power conversion efficiency is critical to improve performance and stability. We find that in our device space, perovskites can tolerate spatial disorder in chemistry, but not charge extraction.
- 30 October 2024
- Published by Springer Nature in Nature Energy
- Vol. 10 (1) , 66-76
Open AccessThe impact of interfacial quality and nanoscale performance disorder on the stability of alloyed perovskite solar cells
Microscopy provides a proxy for assessing the operation of perovskite solar cells, yet most works in the literature have focused on bare perovskite thin films, missing charge transport and recombination losses present in full devices. Here we demonstrate a multimodal operando microscopy toolkit to measure and spatially correlate nanoscale charge transport losses, recombination losses and chemical composition. By applying this toolkit to the same scan areas of state-of-the-art, alloyed perovskite cells before and after extended operation, we show that devices with the highest macroscopic performance have the lowest initial performance spatial heterogeneity—a crucial link that is missed in conventional microscopy. We show that engineering stable interfaces is critical to achieving robust devices. Once the interfaces are stabilized, we show that compositional engineering to homogenize charge extraction and to minimize variations in local power conversion efficiency is critical to improve performance and stability. We find that in our device space, perovskites can tolerate spatial disorder in chemistry, but not charge extraction.
- Top Cited Papers
- 7 July 2023
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 381 (6653) , 63-69
Interface engineering for high-performance, triple-halide perovskite–silicon tandem solar cells
Improved stability and efficiency of two-terminal monolithic perovskite-silicon tandem solar cells will require reductions in recombination losses. By combining a triple-halide perovskite (1.68 electron volt bandgap) with a piperazinium iodide interfacial modification, we improved the band alignment, reduced nonradiative recombination losses, and enhanced charge extraction at the electron-selective contact. Solar cells showed open-circuit voltages of up to 1.28 volts in p-i-n single junctions and 2.00 volts in perovskite-silicon tandem solar cells. The tandem cells achieve certified power conversion efficiencies of up to 32.5%.
- 7 July 2023
- Published by American Association for the Advancement of Science (AAAS) in Science
- Vol. 381 (6653) , 63-69
Top Cited PapersInterface engineering for high-performance, triple-halide perovskite–silicon tandem solar cells
Improved stability and efficiency of two-terminal monolithic perovskite-silicon tandem solar cells will require reductions in recombination losses. By combining a triple-halide perovskite (1.68 electron volt bandgap) with a piperazinium iodide interfacial modification, we improved the band alignment, reduced nonradiative recombination losses, and enhanced charge extraction at the electron-selective contact. Solar cells showed open-circuit voltages of up to 1.28 volts in p-i-n single junctions and 2.00 volts in perovskite-silicon tandem solar cells. The tandem cells achieve certified power conversion efficiencies of up to 32.5%.
- Open Access
- 25 May 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (34)
Advanced Characterization and Optimization of NiOx:Cu‐SAM Hole‐Transporting Bi‐Layer for 23.4% Efficient Monolithic Cu(In,Ga)Se2‐Perovskite Tandem Solar Cells
The performance of five hole‐transporting layers (HTLs) is investigated in both single‐junction perovskite and Cu(In, Ga)Se2 (CIGSe)‐perovskite tandem solar cells: nickel oxide (NiOx,), copper‐doped nickel oxide (NiOx:Cu), NiOx+SAM, NiOx:Cu+SAM, and SAM, where SAM is the [2‐(3,‐6Dimethoxy‐9H‐carbazol‐9yl)ethyl]phosphonic acid (MeO‐2PACz) self‐assembled monolayer. The performance of the devices is correlated to the charge‐carrier dynamics at the HTL/perovskite interface and the limiting factors of these HTLs are analyzed by performing time‐resolved and absolute photoluminescence ((Tr)PL), transient surface photovoltage (tr‐SPV), and X‐ray/UV photoemission spectroscopy (XPS/UPS) measurements on indium tin oxide (ITO)/HTL/perovskite and CIGSe/HTL/perovskite stacks. A high quasi‐Fermi level splitting to open‐circuit (QFLS‐Voc) deficit is detected for the NiOx‐based devices, attributed to electron trapping and poor hole extraction at the NiOx‐perovskite interface and a low carrier effective lifetime in the bulk of the perovskite. Simultaneously, doping the NiOx with 2% Cu and passivating its surface with MeO‐2PACz suppresses the electron trapping, enhances the holes extraction, reduces the non‐radiative interfacial recombination, and improves the band alignment. Due to this superior interfacial charge‐carrier dynamics, NiOx:Cu+SAM is found to be the most suitable HTL for the monolithic CIGSe‐perovskite tandem devices, enabling a power‐conversion efficiency (PCE) of 23.4%, Voc of 1.72V, and a fill factor (FF) of 71%, while the remaining four HTLs suffer from prominent Voc and FF losses.
- 25 May 2023
- Published by Wiley in Advanced Functional Materials
- Vol. 33 (34)
Open AccessAdvanced Characterization and Optimization of NiOx:Cu‐SAM Hole‐Transporting Bi‐Layer for 23.4% Efficient Monolithic Cu(In,Ga)Se2‐Perovskite Tandem Solar Cells
The performance of five hole‐transporting layers (HTLs) is investigated in both single‐junction perovskite and Cu(In, Ga)Se2 (CIGSe)‐perovskite tandem solar cells: nickel oxide (NiOx,), copper‐doped nickel oxide (NiOx:Cu), NiOx+SAM, NiOx:Cu+SAM, and SAM, where SAM is the [2‐(3,‐6Dimethoxy‐9H‐carbazol‐9yl)ethyl]phosphonic acid (MeO‐2PACz) self‐assembled monolayer. The performance of the devices is correlated to the charge‐carrier dynamics at the HTL/perovskite interface and the limiting factors of these HTLs are analyzed by performing time‐resolved and absolute photoluminescence ((Tr)PL), transient surface photovoltage (tr‐SPV), and X‐ray/UV photoemission spectroscopy (XPS/UPS) measurements on indium tin oxide (ITO)/HTL/perovskite and CIGSe/HTL/perovskite stacks. A high quasi‐Fermi level splitting to open‐circuit (QFLS‐Voc) deficit is detected for the NiOx‐based devices, attributed to electron trapping and poor hole extraction at the NiOx‐perovskite interface and a low carrier effective lifetime in the bulk of the perovskite. Simultaneously, doping the NiOx with 2% Cu and passivating its surface with MeO‐2PACz suppresses the electron trapping, enhances the holes extraction, reduces the non‐radiative interfacial recombination, and improves the band alignment. Due to this superior interfacial charge‐carrier dynamics, NiOx:Cu+SAM is found to be the most suitable HTL for the monolithic CIGSe‐perovskite tandem devices, enabling a power‐conversion efficiency (PCE) of 23.4%, Voc of 1.72V, and a fill factor (FF) of 71%, while the remaining four HTLs suffer from prominent Voc and FF losses.
- Top Cited PapersOpen Access
- 6 January 2023
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 8 (2) , 898-900
Wettability Improvement of a Carbazole-Based Hole-Selective Monolayer for Reproducible Perovskite Solar Cells
- 6 January 2023
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 8 (2) , 898-900
Top Cited PapersOpen AccessWettability Improvement of a Carbazole-Based Hole-Selective Monolayer for Reproducible Perovskite Solar Cells
- Top Cited PapersOpen Access
- 24 October 2022
- Published by Springer Nature in Nature Nanotechnology
- Vol. 17 (11) , 1214-1221
Nano-optical designs for high-efficiency monolithic perovskite–silicon tandem solar cells
Perovskite–silicon tandem solar cells offer the possibility of overcoming the power conversion efficiency limit of conventional silicon solar cells. Various textured tandem devices have been presented aiming at improved optical performance, but optimizing film growth on surface-textured wafers remains challenging. Here we present perovskite–silicon tandem solar cells with periodic nanotextures that offer various advantages without compromising the material quality of solution-processed perovskite layers. We show a reduction in reflection losses in comparison to planar tandems, with the new devices being less sensitive to deviations from optimum layer thicknesses. The nanotextures also enable a greatly increased fabrication yield from 50% to 95%. Moreover, the open-circuit voltage is improved by 15 mV due to the enhanced optoelectronic properties of the perovskite top cell. Our optically advanced rear reflector with a dielectric buffer layer results in reduced parasitic absorption at near-infrared wavelengths. As a result, we demonstrate a certified power conversion efficiency of 29.80%.
- 24 October 2022
- Published by Springer Nature in Nature Nanotechnology
- Vol. 17 (11) , 1214-1221
Top Cited PapersOpen AccessNano-optical designs for high-efficiency monolithic perovskite–silicon tandem solar cells
Perovskite–silicon tandem solar cells offer the possibility of overcoming the power conversion efficiency limit of conventional silicon solar cells. Various textured tandem devices have been presented aiming at improved optical performance, but optimizing film growth on surface-textured wafers remains challenging. Here we present perovskite–silicon tandem solar cells with periodic nanotextures that offer various advantages without compromising the material quality of solution-processed perovskite layers. We show a reduction in reflection losses in comparison to planar tandems, with the new devices being less sensitive to deviations from optimum layer thicknesses. The nanotextures also enable a greatly increased fabrication yield from 50% to 95%. Moreover, the open-circuit voltage is improved by 15 mV due to the enhanced optoelectronic properties of the perovskite top cell. Our optically advanced rear reflector with a dielectric buffer layer results in reduced parasitic absorption at near-infrared wavelengths. As a result, we demonstrate a certified power conversion efficiency of 29.80%.
- Open Access
- 27 September 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (10) , 3600-3611
Slot-Die Coated Triple-Halide Perovskites for Efficient and Scalable Perovskite/Silicon Tandem Solar Cells
Wide bandgap halide perovskite materials show promising potential to pair with silicon bottom cells. To date, most efficient wide bandgap perovskites layers are fabricated by spin-coating, which is difficult to scale up. Here, we report on slot-die coating for an efficient, 1.68 eV wide bandgap triple-halide (3halide) perovskite absorber, (Cs0.22FA0.78)Pb(I0.85Br0.15)3 + 5 mol % MAPbCl3. A suitable solvent system is designed specifically for the slot-die coating technique. We demonstrate that our fabrication route is suitable for tandem solar cells without phase segregation. The slot-die coated wet halide perovskite is dried by a "nitrogen (N2)-knife" with high reproducibility and avoiding antisolvents. We explore varying annealing conditions and identify parameters allowing crystallization of the perovskite film into large grains reducing charge collection losses and enabling higher current density. At 150 °C, an optimized trade-off between crystallization and the PbI2 aggregates on the film's top surface is found. Thus, we improve the cell stability and performance of both single-junction cells and tandems. Combining the 3halide top cells with a 120 μm thin saw damage etched commercial Czochralski industrial wafer, a 2-terminal monolithic tandem solar cell with a PCE of 25.2% on a 1 cm2 active area is demonstrated with fully scalable processes.
- 27 September 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (10) , 3600-3611
Open AccessSlot-Die Coated Triple-Halide Perovskites for Efficient and Scalable Perovskite/Silicon Tandem Solar Cells
Wide bandgap halide perovskite materials show promising potential to pair with silicon bottom cells. To date, most efficient wide bandgap perovskites layers are fabricated by spin-coating, which is difficult to scale up. Here, we report on slot-die coating for an efficient, 1.68 eV wide bandgap triple-halide (3halide) perovskite absorber, (Cs0.22FA0.78)Pb(I0.85Br0.15)3 + 5 mol % MAPbCl3. A suitable solvent system is designed specifically for the slot-die coating technique. We demonstrate that our fabrication route is suitable for tandem solar cells without phase segregation. The slot-die coated wet halide perovskite is dried by a "nitrogen (N2)-knife" with high reproducibility and avoiding antisolvents. We explore varying annealing conditions and identify parameters allowing crystallization of the perovskite film into large grains reducing charge collection losses and enabling higher current density. At 150 °C, an optimized trade-off between crystallization and the PbI2 aggregates on the film's top surface is found. Thus, we improve the cell stability and performance of both single-junction cells and tandems. Combining the 3halide top cells with a 120 μm thin saw damage etched commercial Czochralski industrial wafer, a 2-terminal monolithic tandem solar cell with a PCE of 25.2% on a 1 cm2 active area is demonstrated with fully scalable processes.
- Open Access
- 22 June 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (30)
Field Effect Passivation in Perovskite Solar Cells by a LiF Interlayer
The fullerene C60 is commonly applied as the electron transport layer in high‐efficiency metal halide perovskite solar cells and has been found to limit their open circuit voltage. Through ultra‐sensitive near‐UV photoelectron spectroscopy in constant final state mode (CFSYS), with an unusually high probing depth of 5–10 nm, the perovskite/C60 interface energetics and defect formation is investigated. It is demonstrated how to consistently determine the energy level alignment by CFSYS and avoid misinterpretations by accounting for the measurement‐induced surface photovoltage in photoactive layer stacks. The energetic offset between the perovskite valence band maximum and the C60 HOMO‐edge is directly determined to be 0.55 eV. Furthermore, the voltage enhancement upon the incorporation of a LiF interlayer at the interface can be attributed to originate from a mild dipole effect and probably the presence of fixed charges, both reducing the hole concentration in the vicinity of the perovskite/C60 interface. This yields a field effect passivation, which overcompensates the observed enhanced defect density in the first monolayers of C60.
- 22 June 2022
- Published by Wiley in Advanced Energy Materials
- Vol. 12 (30)
Open AccessField Effect Passivation in Perovskite Solar Cells by a LiF Interlayer
The fullerene C60 is commonly applied as the electron transport layer in high‐efficiency metal halide perovskite solar cells and has been found to limit their open circuit voltage. Through ultra‐sensitive near‐UV photoelectron spectroscopy in constant final state mode (CFSYS), with an unusually high probing depth of 5–10 nm, the perovskite/C60 interface energetics and defect formation is investigated. It is demonstrated how to consistently determine the energy level alignment by CFSYS and avoid misinterpretations by accounting for the measurement‐induced surface photovoltage in photoactive layer stacks. The energetic offset between the perovskite valence band maximum and the C60 HOMO‐edge is directly determined to be 0.55 eV. Furthermore, the voltage enhancement upon the incorporation of a LiF interlayer at the interface can be attributed to originate from a mild dipole effect and probably the presence of fixed charges, both reducing the hole concentration in the vicinity of the perovskite/C60 interface. This yields a field effect passivation, which overcompensates the observed enhanced defect density in the first monolayers of C60.
- Top Cited Papers
- 13 April 2022
- Published by Springer Nature in Nature
- Vol. 604 (7905) , 280-286
Perovskite–organic tandem solar cells with indium oxide interconnect
Multijunction solar cells can overcome the fundamental efficiency limits of single-junction devices. The bandgap tunability of metal halide perovskite solar cells renders them attractive for multijunction architectures1. Combinations with silicon and copper indium gallium selenide (CIGS), as well as all-perovskite tandem cells, have been reported2,3,4,5. Meanwhile, narrow-gap non-fullerene acceptors have unlocked skyrocketing efficiencies for organic solar cells6,7. Organic and perovskite semiconductors are an attractive combination, sharing similar processing technologies. Currently, perovskite–organic tandems show subpar efficiencies and are limited by the low open-circuit voltage (Voc) of wide-gap perovskite cells8 and losses introduced by the interconnect between the subcells9,10. Here we demonstrate perovskite–organic tandem cells with an efficiency of 24.0 per cent (certified 23.1 per cent) and a high Voc of 2.15 volts. Optimized charge extraction layers afford perovskite subcells with an outstanding combination of high Voc and fill factor. The organic subcells provide a high external quantum efficiency in the near-infrared and, in contrast to paradigmatic concerns about limited photostability of non-fullerene cells11, show an outstanding operational stability if excitons are predominantly generated on the non-fullerene acceptor, which is the case in our tandems. The subcells are connected by an ultrathin (approximately 1.5 nanometres) metal-like indium oxide layer with unprecedented low optical/electrical losses. This work sets a milestone for perovskite–organic tandems, which outperform the best p–i–n perovskite single junctions12 and are on a par with perovskite–CIGS and all-perovskite multijunctions13.
- 13 April 2022
- Published by Springer Nature in Nature
- Vol. 604 (7905) , 280-286
Top Cited PapersPerovskite–organic tandem solar cells with indium oxide interconnect
Multijunction solar cells can overcome the fundamental efficiency limits of single-junction devices. The bandgap tunability of metal halide perovskite solar cells renders them attractive for multijunction architectures1. Combinations with silicon and copper indium gallium selenide (CIGS), as well as all-perovskite tandem cells, have been reported2,3,4,5. Meanwhile, narrow-gap non-fullerene acceptors have unlocked skyrocketing efficiencies for organic solar cells6,7. Organic and perovskite semiconductors are an attractive combination, sharing similar processing technologies. Currently, perovskite–organic tandems show subpar efficiencies and are limited by the low open-circuit voltage (Voc) of wide-gap perovskite cells8 and losses introduced by the interconnect between the subcells9,10. Here we demonstrate perovskite–organic tandem cells with an efficiency of 24.0 per cent (certified 23.1 per cent) and a high Voc of 2.15 volts. Optimized charge extraction layers afford perovskite subcells with an outstanding combination of high Voc and fill factor. The organic subcells provide a high external quantum efficiency in the near-infrared and, in contrast to paradigmatic concerns about limited photostability of non-fullerene cells11, show an outstanding operational stability if excitons are predominantly generated on the non-fullerene acceptor, which is the case in our tandems. The subcells are connected by an ultrathin (approximately 1.5 nanometres) metal-like indium oxide layer with unprecedented low optical/electrical losses. This work sets a milestone for perovskite–organic tandems, which outperform the best p–i–n perovskite single junctions12 and are on a par with perovskite–CIGS and all-perovskite multijunctions13.
- Top Cited PapersOpen Access
- 9 March 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (4) , 1298-1307
Perovskite/CIGS Tandem Solar Cells: From Certified 24.2% toward 30% and Beyond
- 9 March 2022
- Published by American Chemical Society (ACS) in ACS Energy Letters
- Vol. 7 (4) , 1298-1307
Top Cited PapersOpen AccessPerovskite/CIGS Tandem Solar Cells: From Certified 24.2% toward 30% and Beyond
- Open Access
- 22 December 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 14 (1) , 2166-2176
Enhanced Self-Assembled Monolayer Surface Coverage by ALD NiO in p-i-n Perovskite Solar Cells
Metal halide perovskites have attracted tremendous attention due to their excellent electronic properties. Recent advancements in device performance and stability of perovskite solar cells (PSCs) have been achieved with the application of self-assembled monolayers (SAMs), serving as stand-alone hole transport layers in the p-i-n architecture. Specifically, phosphonic acid SAMs, directly functionalizing indium–tin oxide (ITO), are presently adopted for highly efficient devices. Despite their successes, so far, little is known about the surface coverage of SAMs on ITO used in PSCs application, which can affect the device performance, as non-covered areas can result in shunting or low open-circuit voltage. In this study, we investigate the surface coverage of SAMs on ITO and observe that the SAM of MeO-2PACz ([2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid) inhomogeneously covers the ITO substrate. Instead, when adopting an intermediate layer of NiO between ITO and the SAM, the homogeneity, and hence the surface coverage of the SAM, improve. In this work, NiO is processed by plasma-assisted atomic layer deposition (ALD) with Ni(MeCp)2 as the precursor and O2 plasma as the co-reactant. Specifically, the presence of ALD NiO leads to a homogeneous distribution of SAM molecules on the metal oxide area, accompanied by a high shunt resistance in the devices with respect to those with SAM directly processed on ITO. At the same time, the SAM is key to the improvement of the open-circuit voltage of NiO + MeO-2PACz devices compared to those with NiO alone. Thus, the combination of NiO and SAM results in a narrower distribution of device performance reaching a more than 20% efficient champion device. The enhancement of SAM coverage in the presence of NiO is corroborated by several characterization techniques including advanced imaging by transmission electron microscopy (TEM), elemental composition quantification by Rutherford backscattering spectrometry (RBS), and conductive atomic force microscopy (c-AFM) mapping. We believe this finding will further promote the usage of phosphonic acid based SAM molecules in perovskite PV.
- 22 December 2021
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 14 (1) , 2166-2176
Open AccessEnhanced Self-Assembled Monolayer Surface Coverage by ALD NiO in p-i-n Perovskite Solar Cells
Metal halide perovskites have attracted tremendous attention due to their excellent electronic properties. Recent advancements in device performance and stability of perovskite solar cells (PSCs) have been achieved with the application of self-assembled monolayers (SAMs), serving as stand-alone hole transport layers in the p-i-n architecture. Specifically, phosphonic acid SAMs, directly functionalizing indium–tin oxide (ITO), are presently adopted for highly efficient devices. Despite their successes, so far, little is known about the surface coverage of SAMs on ITO used in PSCs application, which can affect the device performance, as non-covered areas can result in shunting or low open-circuit voltage. In this study, we investigate the surface coverage of SAMs on ITO and observe that the SAM of MeO-2PACz ([2-(3,6-dimethoxy-9H-carbazol-9-yl)ethyl]phosphonic acid) inhomogeneously covers the ITO substrate. Instead, when adopting an intermediate layer of NiO between ITO and the SAM, the homogeneity, and hence the surface coverage of the SAM, improve. In this work, NiO is processed by plasma-assisted atomic layer deposition (ALD) with Ni(MeCp)2 as the precursor and O2 plasma as the co-reactant. Specifically, the presence of ALD NiO leads to a homogeneous distribution of SAM molecules on the metal oxide area, accompanied by a high shunt resistance in the devices with respect to those with SAM directly processed on ITO. At the same time, the SAM is key to the improvement of the open-circuit voltage of NiO + MeO-2PACz devices compared to those with NiO alone. Thus, the combination of NiO and SAM results in a narrower distribution of device performance reaching a more than 20% efficient champion device. The enhancement of SAM coverage in the presence of NiO is corroborated by several characterization techniques including advanced imaging by transmission electron microscopy (TEM), elemental composition quantification by Rutherford backscattering spectrometry (RBS), and conductive atomic force microscopy (c-AFM) mapping. We believe this finding will further promote the usage of phosphonic acid based SAM molecules in perovskite PV.