Elisson Brum Dutra da Rocha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Elisson Brum Dutra da Rocha has a total of 34 co-authors. Here are the top co-authors by number of shared publications:
- Ana Maria Furtado de Sousa
Rio de Janeiro State University
10 shared publications - Cristina Russi Guimarães Furtado
Rio de Janeiro State University
7 shared publications - Gustavo Ninho Campos
Chemistry Institute Rio de Janeiro State University Rio de Janeiro Rio de Janeiro Brazil
6 shared publications Ana Maria Furtado de Sousa
3 shared publicationsAna Lucia Nazareth da Silva
2 shared publicationsCléverson Fernandes Senra Gabriel
2 shared publications
Latest Publications
- 10 September 2026
- Published by SAGE Publications in Journal of Elastomers & Plastics
Effect of pre-crosslinked NBR on the processing behavior and sealing properties of a carbon black-filled O-ring formulation
Pre-crosslinked acrylonitrile-butadiene rubber (NBR-2PC) is commercially promoted for enhanced processing behavior and permanent compression set. However, its structure–processing–property relationships remain scarcely documented in the academic literature. This study replaced standard NBR grade (NBR-2) with NBR-2PC (0–40 phr) in a carbon black filled O-ring formulation to evaluate both processing and mechanical performance. Increasing NBR-2PC content enhanced the elastic behavior response of uncured compounds, as evidenced by reduced Mooney stress relaxation rates and increased low-strain storage modulus. The Payne effect increased with NBR-2PC content despite constant carbon black loading (45 phr), consistent with a modified microstructure. Cured state properties showed that hardness remained constant at 70 ± 1 Shore A, crosslink density varied slightly (10.9 x 10 -5 to 9.6 x 10 -5 mol cm -3 ), and vulcanization parameters showed only minor variation. However, both tensile strength (21.3 to 17 MPa) and elongation at break (386 to 310%) decreased. All formulations exhibited identical compressive stress relaxation (∼77% of stress retention) and compression set (9–11%) behaviors. Furthermore, formulations with 40 phr NBR 2PC showed a die swell decrease of approximately 14% and exhibited excellent extrudate surface quality and defect-free Garvey die profiles when compared to the standard NBR grade. These results indicate that pre-crosslinked NBR acts primarily as a processing aid, with observable effects on dimensional stability and flow behavior, while the mechanical properties remain largely unaffected, with the exception of tensile strength and elongation at break.
- 10 September 2026
- Published by SAGE Publications in Journal of Elastomers & Plastics
Effect of pre-crosslinked NBR on the processing behavior and sealing properties of a carbon black-filled O-ring formulation
Pre-crosslinked acrylonitrile-butadiene rubber (NBR-2PC) is commercially promoted for enhanced processing behavior and permanent compression set. However, its structure–processing–property relationships remain scarcely documented in the academic literature. This study replaced standard NBR grade (NBR-2) with NBR-2PC (0–40 phr) in a carbon black filled O-ring formulation to evaluate both processing and mechanical performance. Increasing NBR-2PC content enhanced the elastic behavior response of uncured compounds, as evidenced by reduced Mooney stress relaxation rates and increased low-strain storage modulus. The Payne effect increased with NBR-2PC content despite constant carbon black loading (45 phr), consistent with a modified microstructure. Cured state properties showed that hardness remained constant at 70 ± 1 Shore A, crosslink density varied slightly (10.9 x 10 -5 to 9.6 x 10 -5 mol cm -3 ), and vulcanization parameters showed only minor variation. However, both tensile strength (21.3 to 17 MPa) and elongation at break (386 to 310%) decreased. All formulations exhibited identical compressive stress relaxation (∼77% of stress retention) and compression set (9–11%) behaviors. Furthermore, formulations with 40 phr NBR 2PC showed a die swell decrease of approximately 14% and exhibited excellent extrudate surface quality and defect-free Garvey die profiles when compared to the standard NBR grade. These results indicate that pre-crosslinked NBR acts primarily as a processing aid, with observable effects on dimensional stability and flow behavior, while the mechanical properties remain largely unaffected, with the exception of tensile strength and elongation at break.
- Open Access
- 17 March 2026
- Published by Elsevier in Next Materials
- Vol. 11
Valorization of kombucha SCOBY waste: Developing a natural rubber and bacterial cellulose biocomposite
- 17 March 2026
- Published by Elsevier in Next Materials
- Vol. 11
Open AccessValorization of kombucha SCOBY waste: Developing a natural rubber and bacterial cellulose biocomposite
- Open Access
- 21 January 2026
- Published by Wiley in SPE Polymers
- Vol. 7 (1)
Assessment of the Mixing Procedure and the Effect of Carboxylated Nitrile Rubber as a Compatibilizer for Kraft Lignin/Nitrile Rubber Composites
The growing interest in sustainable rubber materials motivates the use of renewable resources for the development of advanced materials. Lignin, valued for its abundance, biodegradability, and mechanical strengths, emerges as a promising alternative filler in rubber composites. This study produced composites using nitrile rubber (NBR) and a 70:30 blend of NBR with carboxylated nitrile rubber (XNBR), each incorporating 40 parts per hundred of rubber (phr) of kraft lignin. Two methods were tested for incorporating lignin: direct addition of 40 phr of lignin powder to the rubbers or compounding using masterbatches of NBR/lignin and XNBR/lignin, each with 130 phr of lignin produced by co‐coagulation. Results revealed that NBR/XNBR/lignin composites show thinner, more aligned lignin particles than NBR/lignin composites, with the masterbatch technique further reducing particle size. All lignin‐filled rubbers exhibited an increased reaction rate constant of vulcanization, lower covalent crosslink density, and higher ionic crosslink density compared to unfilled rubber. Notably, composites made with lignin masterbatch exhibited a reduced Payne effect, as well as higher tensile and tear strengths, than those made using lignin powder. These findings suggest that incorporating lignin via a masterbatch and blending with XNBR offers a compelling strategy for enhancing the properties of NBR‐based rubber composites.
- 21 January 2026
- Published by Wiley in SPE Polymers
- Vol. 7 (1)
Open AccessAssessment of the Mixing Procedure and the Effect of Carboxylated Nitrile Rubber as a Compatibilizer for Kraft Lignin/Nitrile Rubber Composites
The growing interest in sustainable rubber materials motivates the use of renewable resources for the development of advanced materials. Lignin, valued for its abundance, biodegradability, and mechanical strengths, emerges as a promising alternative filler in rubber composites. This study produced composites using nitrile rubber (NBR) and a 70:30 blend of NBR with carboxylated nitrile rubber (XNBR), each incorporating 40 parts per hundred of rubber (phr) of kraft lignin. Two methods were tested for incorporating lignin: direct addition of 40 phr of lignin powder to the rubbers or compounding using masterbatches of NBR/lignin and XNBR/lignin, each with 130 phr of lignin produced by co‐coagulation. Results revealed that NBR/XNBR/lignin composites show thinner, more aligned lignin particles than NBR/lignin composites, with the masterbatch technique further reducing particle size. All lignin‐filled rubbers exhibited an increased reaction rate constant of vulcanization, lower covalent crosslink density, and higher ionic crosslink density compared to unfilled rubber. Notably, composites made with lignin masterbatch exhibited a reduced Payne effect, as well as higher tensile and tear strengths, than those made using lignin powder. These findings suggest that incorporating lignin via a masterbatch and blending with XNBR offers a compelling strategy for enhancing the properties of NBR‐based rubber composites.
- Open Access
- 1 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 3983-3993
Mechanical Performance Under Compressive Load of Carboxylated Nitrile Rubber and Kraft Lignin Composites
Lignin is a promising biobased material that enhances the sustainability of rubber composites as a reinforcing filler. This study investigates 10 formulations of carboxylated nitrile rubber (XNBR) filled with Kraft lignin, focusing on their compressive mechanical properties, which are related to sealing applications. Key assessments include stress–strain behavior under compression, stress relaxation, and compression set. Characterization techniques like micro‐computed tomography (micro‐CT) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR) were also employed. Micro‐CT imaging indicates that XNBR with 7% carboxylic acid exhibits significantly better lignin dispersion than formulations with just 1% carboxylic acid. The compressive properties of the composites depend on the rubber's carboxylic acid content; for instance, adding lignin to rubber with 1% carboxylic acid had minimal impact on stress at 50%, while it nearly doubled in rubber with 7%. Higher lignin content leads to increased hysteresis, stress relaxation, and compression sets, particularly as carboxylic acid content rises. ATR‐FTIR analysis suggests that ionic bonds in carboxylated rubbers play a crucial role in their interaction with lignin, enhancing mechanical performance.
- 1 September 2025
- Published by Wiley in Polymer Composites
- Vol. 47 (5) , 3983-3993
Open AccessMechanical Performance Under Compressive Load of Carboxylated Nitrile Rubber and Kraft Lignin Composites
Lignin is a promising biobased material that enhances the sustainability of rubber composites as a reinforcing filler. This study investigates 10 formulations of carboxylated nitrile rubber (XNBR) filled with Kraft lignin, focusing on their compressive mechanical properties, which are related to sealing applications. Key assessments include stress–strain behavior under compression, stress relaxation, and compression set. Characterization techniques like micro‐computed tomography (micro‐CT) and attenuated total reflectance Fourier transform infrared spectroscopy (ATR‐FTIR) were also employed. Micro‐CT imaging indicates that XNBR with 7% carboxylic acid exhibits significantly better lignin dispersion than formulations with just 1% carboxylic acid. The compressive properties of the composites depend on the rubber's carboxylic acid content; for instance, adding lignin to rubber with 1% carboxylic acid had minimal impact on stress at 50%, while it nearly doubled in rubber with 7%. Higher lignin content leads to increased hysteresis, stress relaxation, and compression sets, particularly as carboxylic acid content rises. ATR‐FTIR analysis suggests that ionic bonds in carboxylated rubbers play a crucial role in their interaction with lignin, enhancing mechanical performance.
- 28 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 5907-5922
Advantages of using a dual‐filler system with carbon black and rockwool fiber on Nitrile Rubber composites from a technical standpoint
This study produced and characterized composites based on nitrile rubber reinforced with rockwool fiber (RW) and carbon black (CB). Ten formulations with dual‐filler loading amounts ranging from 0 to 40 phr of CB and RW were designed using a simplex‐centroid mixture. The composites were assessed regarding their rheometric, rheological, mechanical, and thermal properties. The use of the RW in the dual‐filler system contributed to overall improvements in Shore A hardness, tear strength, modulus at 50%, and resilience, as well as reducing the Payne effect. Instead of using 40 phr of CB alone, a dual‐filler system comprising 20 phr of CB and 20 phr of RW lowers the Payne effect by around 60%, improves resilience by 35%, modulus at 50% strain by 8%, and the residual stress at equilibrium (σ∞/σ0) by 7%. On the other hand, the tensile strength is reduced by 23%. The optimum cure time, crosslink density, and maximum decomposition rate temperature were not affected by the rockwool's presence in the dual‐filler system. In general, the use of RW in combination with CB is advantageous mainly because it reduces compressive stress relaxation, which is an important property for sealing applications.Highlights: Dual‐filler systems based on carbon black (CB) and rockwool fiber (RW) offer advantages. RW‐rich dual‐filler systems reduce stress relaxation. RW‐rich dual‐filler systems reduce the Payne effect. CB‐rich dual‐filler systems increase tensile strength.
- 28 January 2024
- Published by Wiley in Polymer Composites
- Vol. 45 (7) , 5907-5922
Advantages of using a dual‐filler system with carbon black and rockwool fiber on Nitrile Rubber composites from a technical standpoint
This study produced and characterized composites based on nitrile rubber reinforced with rockwool fiber (RW) and carbon black (CB). Ten formulations with dual‐filler loading amounts ranging from 0 to 40 phr of CB and RW were designed using a simplex‐centroid mixture. The composites were assessed regarding their rheometric, rheological, mechanical, and thermal properties. The use of the RW in the dual‐filler system contributed to overall improvements in Shore A hardness, tear strength, modulus at 50%, and resilience, as well as reducing the Payne effect. Instead of using 40 phr of CB alone, a dual‐filler system comprising 20 phr of CB and 20 phr of RW lowers the Payne effect by around 60%, improves resilience by 35%, modulus at 50% strain by 8%, and the residual stress at equilibrium (σ∞/σ0) by 7%. On the other hand, the tensile strength is reduced by 23%. The optimum cure time, crosslink density, and maximum decomposition rate temperature were not affected by the rockwool's presence in the dual‐filler system. In general, the use of RW in combination with CB is advantageous mainly because it reduces compressive stress relaxation, which is an important property for sealing applications.Highlights: Dual‐filler systems based on carbon black (CB) and rockwool fiber (RW) offer advantages. RW‐rich dual‐filler systems reduce stress relaxation. RW‐rich dual‐filler systems reduce the Payne effect. CB‐rich dual‐filler systems increase tensile strength.
- 20 December 2023
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4124-4137
Using carboxyl groups to improve the compatibility of XNBR/lignin composites
The paper and pulp industry produces lignin as a byproduct, which could be a bio‐based reinforcing filler for rubber. Carboxylated nitrile rubber (XNBR) contains carboxyl groups that form ionic bonds with zinc oxide, potentially increasing compatibility with lignin, compared to usual nonpolar rubbers. This study employed the traditional mixing method, two‐roll mill, to incorporate hardwood Kraft lignin without chemical or physical modification as a reinforcing filler in commercial XNBR. A mixture design of experiments was used to explore the effect on rubber/lignin interaction of the carboxyl group content (from 1% to 7% in blends of XNBR) and the amount of lignin (from 0 to 40 phr). Adding 40 phr of lignin increased stress at 100% in XNBR 7% from 1.7 to 6.3 MPa. In XNBR 1%, the increase was from 1.2 to 1.9 MPa. Lignin showed better interaction and dispersion with XNBR 7%, determined from response surface of G′ at high deformations and SEM, respectively. Loss of thermal transition in DMA indicates interaction through ionic groups. These results show that the presence of carboxyl groups enhances the rubber/lignin interaction. This research open possibilities of compatibilization of lignin, offering guidance for future studies and technologies involving lignin in technical applications.Highlights: Lignin dispersion increased as the carboxyl group content increased to 7% (w/w). Stress at 100% elongation increased 370% with 40 phr of lignin and 7% carboxyl. Rubber/lignin interaction as per G′ increased with carboxyl groups. Loss of thermal transition suggests lignin/carboxy/zinc oxide interaction. Lignin can be used as a reinforcing filler in nitrile carboxylated rubber.
- 20 December 2023
- Published by Wiley in Polymer Composites
- Vol. 45 (5) , 4124-4137
Using carboxyl groups to improve the compatibility of XNBR/lignin composites
The paper and pulp industry produces lignin as a byproduct, which could be a bio‐based reinforcing filler for rubber. Carboxylated nitrile rubber (XNBR) contains carboxyl groups that form ionic bonds with zinc oxide, potentially increasing compatibility with lignin, compared to usual nonpolar rubbers. This study employed the traditional mixing method, two‐roll mill, to incorporate hardwood Kraft lignin without chemical or physical modification as a reinforcing filler in commercial XNBR. A mixture design of experiments was used to explore the effect on rubber/lignin interaction of the carboxyl group content (from 1% to 7% in blends of XNBR) and the amount of lignin (from 0 to 40 phr). Adding 40 phr of lignin increased stress at 100% in XNBR 7% from 1.7 to 6.3 MPa. In XNBR 1%, the increase was from 1.2 to 1.9 MPa. Lignin showed better interaction and dispersion with XNBR 7%, determined from response surface of G′ at high deformations and SEM, respectively. Loss of thermal transition in DMA indicates interaction through ionic groups. These results show that the presence of carboxyl groups enhances the rubber/lignin interaction. This research open possibilities of compatibilization of lignin, offering guidance for future studies and technologies involving lignin in technical applications.Highlights: Lignin dispersion increased as the carboxyl group content increased to 7% (w/w). Stress at 100% elongation increased 370% with 40 phr of lignin and 7% carboxyl. Rubber/lignin interaction as per G′ increased with carboxyl groups. Loss of thermal transition suggests lignin/carboxy/zinc oxide interaction. Lignin can be used as a reinforcing filler in nitrile carboxylated rubber.
- 2 June 2023
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (4) , 3209-3227
Application of ATR-FTIR spectroscopy to characterize the acrylonitrile content of degraded filled nitrile rubber compounds
- 2 June 2023
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (4) , 3209-3227
Application of ATR-FTIR spectroscopy to characterize the acrylonitrile content of degraded filled nitrile rubber compounds
- 26 May 2023
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (4) , 3007-3019
Evaluation of thermoforming potential of polystyrene/perlite composites
- 26 May 2023
- Published by Springer Nature in Polymer Bulletin
- Vol. 81 (4) , 3007-3019
Evaluation of thermoforming potential of polystyrene/perlite composites
- Open Access
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 32 (1)
Cross-link density measurement of nitrile rubber vulcanizates using dynamic shear test
- 1 January 2022
- Published by FapUNIFESP (SciELO) in Polímeros
- Vol. 32 (1)
Open AccessCross-link density measurement of nitrile rubber vulcanizates using dynamic shear test
- 1 February 2020
- Published by Elsevier in Polymer Testing
- Vol. 82
Properties Investigation of novel nitrile rubber composites with rockwool fibers
- 1 February 2020
- Published by Elsevier in Polymer Testing
- Vol. 82
Properties Investigation of novel nitrile rubber composites with rockwool fibers