Gian Francesco Lorusso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gian Francesco Lorusso has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
Masami Ikota
Hitachi High-Tech Corp., Japan
2 shared publicationsAlain Moussa
Imec, Kapeldreef 75, 3001 Leuven, Belgium
1 shared publicationAlex Goldenshtein
Applied Materials, 8, Prof. A. D. Bergman St 4, Rehovot, Israel
1 shared publicationAngelika Muellender
Carl Zeiss SMT GmbH, Carl-Zeiss-Straße 22, 73447 Oberkochen, Germany
1 shared publicationAnne-Laure Charley
Imec, Kapeldreef 75, 3001 Leuven, Belgium
1 shared publicationBappaditya Dey
Imec, Kapeldreef 75, 3001 Leuven, Belgium
1 shared publication
Latest Publications
- 14 April 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SG) , SG0808
e-beam metrology of thin resist for high NA EUVL
One of the many constraints of high numerical aperture extreme ultraviolet lithography is related to resist thickness. A critical consequence of moving from the current 0.33 to 0.55 NA (high NA) is depth of focus reduction. The question we seek to answer in the present study is how the resist thickness reduction, required to compensate for the drop in NA, impacts the e-beam metrology needed to characterize the process. The impact of film thickness on e-beam metrology was first investigated by critical dimension scanning electron microscopy (CD SEM) using our current best-known methods (BKMs). Optimized settings minimizing such an impact were then studied using CD SEM as well as low-voltage SEM. Atomic force microscopy was used to accurately characterize the sample thickness. Our results indicate that alternative operating conditions and BKMs are sometimes needed to meet the metrology requirements. However, even in the case of materials showing a large sensitivity to resist thinning, we were able to identify e-beam imaging conditions capable of meeting metrology specifications.
- 14 April 2023
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 62 (SG) , SG0808
e-beam metrology of thin resist for high NA EUVL
One of the many constraints of high numerical aperture extreme ultraviolet lithography is related to resist thickness. A critical consequence of moving from the current 0.33 to 0.55 NA (high NA) is depth of focus reduction. The question we seek to answer in the present study is how the resist thickness reduction, required to compensate for the drop in NA, impacts the e-beam metrology needed to characterize the process. The impact of film thickness on e-beam metrology was first investigated by critical dimension scanning electron microscopy (CD SEM) using our current best-known methods (BKMs). Optimized settings minimizing such an impact were then studied using CD SEM as well as low-voltage SEM. Atomic force microscopy was used to accurately characterize the sample thickness. Our results indicate that alternative operating conditions and BKMs are sometimes needed to meet the metrology requirements. However, even in the case of materials showing a large sensitivity to resist thinning, we were able to identify e-beam imaging conditions capable of meeting metrology specifications.
- 21 May 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (SD) , SD0801
Electron beam metrology for advanced technology nodes
The critical dimension scanning electron microscope (CD-SEM) is one of the main tools used to estimate critical dimension (CD) in semiconductor manufacturing nowadays, but, as all metrology tools, it will face considerable challenges to keep up with the requirements of the future technology nodes. The root causes of these challenges are not uniquely related to the shrinking CD values, as one might expect, but to the increase in complexity of the devices in of morphology and chemical composition as well. In fact, complicated three-dimensional device architectures, high aspect ratio features, and wide variety of materials are some of the unavoidable characteristics of the future metrology nodes. In this paper, we report on the development of advanced CD-SEM metrology at imec on a variety of device platforms and processes, for both logics and memories. The large variety of results reported here a clear indication of the on-going creative effort needed to ensure that the critical potential of CD-SEM metrology tools is fully enabled for the 5 nm node and beyond.
- 21 May 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (SD) , SD0801
Electron beam metrology for advanced technology nodes
The critical dimension scanning electron microscope (CD-SEM) is one of the main tools used to estimate critical dimension (CD) in semiconductor manufacturing nowadays, but, as all metrology tools, it will face considerable challenges to keep up with the requirements of the future technology nodes. The root causes of these challenges are not uniquely related to the shrinking CD values, as one might expect, but to the increase in complexity of the devices in of morphology and chemical composition as well. In fact, complicated three-dimensional device architectures, high aspect ratio features, and wide variety of materials are some of the unavoidable characteristics of the future metrology nodes. In this paper, we report on the development of advanced CD-SEM metrology at imec on a variety of device platforms and processes, for both logics and memories. The large variety of results reported here a clear indication of the on-going creative effort needed to ensure that the critical potential of CD-SEM metrology tools is fully enabled for the 5 nm node and beyond.