Soham Sinha
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Soham Sinha has a total of 45 co-authors. Here are the top co-authors by number of shared publications:
- Jianyi Du
Department of Bioengineering, Stanford University, Stanford, CA, 94305, USA
3 shared publications - M. Saad Bhamla
Chemical and Biological Engineering, University of Colorado, Boulder CO 80309
3 shared publications - Mark A. Skylar-Scott
Department of Bioengineering Stanford University Stanford CA 94305 USA
3 shared publications - Gaurav Byagathvalli
School of Chemical and Biomolecular Engineering, Georgia Institute of Technology, Atlanta, GA 30332
2 shared publications - Janet Standeven
Lambert High School, Suwanee, Georgia, United States of America
2 shared publications - Stacey Lee
Department of Bioengineering Stanford University Stanford CA 94305 USA
2 shared publications
Latest Publications
- Open Access
Gradient Multinozzle 3D Printing
Direct ink writing is compatible with an expansive materials palette. While enabling diverse applications, this materials versatility brings significant bottlenecks in ink formulation, often requiring the mixing, printing, and testing of dozens to hundreds of ink compositions over the course of a project. To accelerate ink-space exploration, we introduce gradient embedded multinozzle (GEM) printheads that combine the high-throughput parallelized printing of multinozzles with combinatorial ink mixing. These printheads allow simultaneous mixing of two-, three-, and four-input inks which are distributed to printer nozzles to create complex 3D structures with graded compositions of inks. Using a two-way GEM printhead, we vali-date cell compatibility by printing scaffolds containing various concentrations of fibroblasts and observing non-linear compaction behaviours. We next test a three-way GEM multinozzle to print ten compositions of di- and multi-functionalized poly(ethylene-glycol) diacrylate hydrogel tri-leaflet valves, optimizing for stiffness, swelling ratio, and toughness. Our GEM multinozzles are compatible with open-source printers and either pressure- or volume-driven extrusion systems and promise to accelerate iterative ink design and testing.
Open AccessGradient Multinozzle 3D Printing
Direct ink writing is compatible with an expansive materials palette. While enabling diverse applications, this materials versatility brings significant bottlenecks in ink formulation, often requiring the mixing, printing, and testing of dozens to hundreds of ink compositions over the course of a project. To accelerate ink-space exploration, we introduce gradient embedded multinozzle (GEM) printheads that combine the high-throughput parallelized printing of multinozzles with combinatorial ink mixing. These printheads allow simultaneous mixing of two-, three-, and four-input inks which are distributed to printer nozzles to create complex 3D structures with graded compositions of inks. Using a two-way GEM printhead, we vali-date cell compatibility by printing scaffolds containing various concentrations of fibroblasts and observing non-linear compaction behaviours. We next test a three-way GEM multinozzle to print ten compositions of di- and multi-functionalized poly(ethylene-glycol) diacrylate hydrogel tri-leaflet valves, optimizing for stiffness, swelling ratio, and toughness. Our GEM multinozzles are compatible with open-source printers and either pressure- or volume-driven extrusion systems and promise to accelerate iterative ink design and testing.
- Open Access
- 22 November 2022
- Published by Wiley in Advanced Healthcare Materials
- Vol. 11 (24)
Large‐Scale Production of Wholly Cellular Bioinks via the Optimization of Human Induced Pluripotent Stem Cell Aggregate Culture in Automated Bioreactors
Combining the sustainable culture of billions of human cells and the bioprinting of wholly cellular bioinks offers a pathway toward organ‐scale tissue engineering. Traditional 2D culture methods are not inherently scalable due to cost, space, and handling constraints. Here, the suspension culture of human induced pluripotent stem cell‐derived aggregates (hAs) is optimized using an automated 250 mL stirred tank bioreactor system. Cell yield, aggregate morphology, and pluripotency marker expression are maintained over three serial passages in two distinct cell lines. Furthermore, it is demonstrated that the same optimized parameters can be scaled to an automated 1 L stirred tank bioreactor system. This 4‐day culture results in a 16.6‐ to 20.4‐fold expansion of cells, generating approximately 4 billion cells per vessel, while maintaining >94% expression of pluripotency markers. The pluripotent aggregates can be subsequently differentiated into derivatives of the three germ layers, including cardiac aggregates, and vascular, cortical and intestinal organoids. Finally, the aggregates are compacted into a wholly cellular bioink for rheological characterization and 3D bioprinting. The printed hAs are subsequently differentiated into neuronal and vascular tissue. This work demonstrates an optimized suspension culture‐to‐3D bioprinting pipeline that enables a sustainable approach to billion cell‐scale organ engineering.
- 22 November 2022
- Published by Wiley in Advanced Healthcare Materials
- Vol. 11 (24)
Open AccessLarge‐Scale Production of Wholly Cellular Bioinks via the Optimization of Human Induced Pluripotent Stem Cell Aggregate Culture in Automated Bioreactors
Combining the sustainable culture of billions of human cells and the bioprinting of wholly cellular bioinks offers a pathway toward organ‐scale tissue engineering. Traditional 2D culture methods are not inherently scalable due to cost, space, and handling constraints. Here, the suspension culture of human induced pluripotent stem cell‐derived aggregates (hAs) is optimized using an automated 250 mL stirred tank bioreactor system. Cell yield, aggregate morphology, and pluripotency marker expression are maintained over three serial passages in two distinct cell lines. Furthermore, it is demonstrated that the same optimized parameters can be scaled to an automated 1 L stirred tank bioreactor system. This 4‐day culture results in a 16.6‐ to 20.4‐fold expansion of cells, generating approximately 4 billion cells per vessel, while maintaining >94% expression of pluripotency markers. The pluripotent aggregates can be subsequently differentiated into derivatives of the three germ layers, including cardiac aggregates, and vascular, cortical and intestinal organoids. Finally, the aggregates are compacted into a wholly cellular bioink for rheological characterization and 3D bioprinting. The printed hAs are subsequently differentiated into neuronal and vascular tissue. This work demonstrates an optimized suspension culture‐to‐3D bioprinting pipeline that enables a sustainable approach to billion cell‐scale organ engineering.
- Open Access
A Visual, Inexpensive, and Wireless Capillary Rheometer
Complex fluid systems can exhibit highly non-linear and time-dependent flow behaviors that arise from microscale reorganization. Rheological measurements to understand these flow-induced properties in soft condensed matter and biology are critical to optimize manufacturing processes that rely upon the use of complex fluids, such as the creation of viscoelastic bioinks for 3D bioprinting. While typical rheological characterizations are performed on bulky and expensive rheometers, these options do not readily enable in situ microscopic visualization of flow behavior, which can provide microstructural insights into the mechanisms and patterns of yielding. To address these limitations, we present a visual, inexpensive (approximately $200), and wireless capillary rheometer (VIEWR) assembled from chiefly 3D printed components. We validate the accuracy and reliability of the portable rheometer by comparing measurements of multiple rheological parameters, including viscosity and yield stress, with measurements obtained from a commercial oscillatory rheometer. At its core, VIEWR employs an easily interchangeable glass capillary channel to enable real-time microscopic observation under flow conditions. To facilitate various experimental conditions, a communication protocol based on Internet of Things (IoT) is adapted to support wireless transmission of data. This unique rheometer design can be used for characterizing and visualizing numerous living and non-living complex fluids. Specifications table:
Open AccessA Visual, Inexpensive, and Wireless Capillary Rheometer
Complex fluid systems can exhibit highly non-linear and time-dependent flow behaviors that arise from microscale reorganization. Rheological measurements to understand these flow-induced properties in soft condensed matter and biology are critical to optimize manufacturing processes that rely upon the use of complex fluids, such as the creation of viscoelastic bioinks for 3D bioprinting. While typical rheological characterizations are performed on bulky and expensive rheometers, these options do not readily enable in situ microscopic visualization of flow behavior, which can provide microstructural insights into the mechanisms and patterns of yielding. To address these limitations, we present a visual, inexpensive (approximately $200), and wireless capillary rheometer (VIEWR) assembled from chiefly 3D printed components. We validate the accuracy and reliability of the portable rheometer by comparing measurements of multiple rheological parameters, including viscosity and yield stress, with measurements obtained from a commercial oscillatory rheometer. At its core, VIEWR employs an easily interchangeable glass capillary channel to enable real-time microscopic observation under flow conditions. To facilitate various experimental conditions, a communication protocol based on Internet of Things (IoT) is adapted to support wireless transmission of data. This unique rheometer design can be used for characterizing and visualizing numerous living and non-living complex fluids. Specifications table:
- Open Access
- 23 September 2020
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 15 (9) , e0238922
LoCHAid: An ultra-low-cost hearing aid for age-related hearing loss
Hearing aids are the primary tool in non-medical rehabilitation for individuals with hearing loss. While the costs of the electronic components have reduced substantially, the cost of a hearing aid has risen steadily to the point that it has become unaffordable for the majority of the population with Age-Related Hearing Loss (ARHL) especially for those residing in low- and middle-income countries. Here, we present an ultra-low-cost, affordable and accessible hearing aid device (‘LoCHAid’), specifically targeted towards treating ARHL in elderly patients. The LoCHAid components cost 98 cents (< $1) when purchased in bulk for 10,000 units and can be personalized for each user through a 3D-printable case. It is designed to be an over-the-counter (OTC) self-serviceable solution for elderly individuals with ARHL. Electroacoustic measurements show that the device meets most of the targets set out by the WHO Preferred Product Profile and Consumer Technology Association for hearing aids. The frequency response of the hearing aid shows selectable gain in the range of 4-8 kHz, and mild to moderate gain between 200-1000 Hz, and shows very limited total distortion (1%). Simulated gain measurements show that the LoCHAid is well fitted to a range of ARHL profiles for males and females between the ages of 60-79 years. Overall, the measurements show that the device offers the potential to benefit individuals with ARHL. Thus, our proposed design has the potential to address the challenge of affordable and accessible hearing technology for hearing impaired elderly individuals especially in low- and middle-income countries.
- 23 September 2020
- Published by Public Library of Science (PLoS) in PLOS ONE
- Vol. 15 (9) , e0238922
Open AccessLoCHAid: An ultra-low-cost hearing aid for age-related hearing loss
Hearing aids are the primary tool in non-medical rehabilitation for individuals with hearing loss. While the costs of the electronic components have reduced substantially, the cost of a hearing aid has risen steadily to the point that it has become unaffordable for the majority of the population with Age-Related Hearing Loss (ARHL) especially for those residing in low- and middle-income countries. Here, we present an ultra-low-cost, affordable and accessible hearing aid device (‘LoCHAid’), specifically targeted towards treating ARHL in elderly patients. The LoCHAid components cost 98 cents (< $1) when purchased in bulk for 10,000 units and can be personalized for each user through a 3D-printable case. It is designed to be an over-the-counter (OTC) self-serviceable solution for elderly individuals with ARHL. Electroacoustic measurements show that the device meets most of the targets set out by the WHO Preferred Product Profile and Consumer Technology Association for hearing aids. The frequency response of the hearing aid shows selectable gain in the range of 4-8 kHz, and mild to moderate gain between 200-1000 Hz, and shows very limited total distortion (1%). Simulated gain measurements show that the LoCHAid is well fitted to a range of ARHL profiles for males and females between the ages of 60-79 years. Overall, the measurements show that the device offers the potential to benefit individuals with ARHL. Thus, our proposed design has the potential to address the challenge of affordable and accessible hearing technology for hearing impaired elderly individuals especially in low- and middle-income countries.
- Open Access
- 10 January 2020
- Published by Public Library of Science (PLoS) in PLOS Biology
- Vol. 18 (1) , e3000589
ElectroPen: An ultra-low–cost, electricity-free, portable electroporator
Electroporation is a basic yet powerful method for delivering small molecules (RNA, DNA, drugs) across cell membranes by application of an electrical field. It is used for many diverse applications, from genetically engineering cells to drug- and DNA-based vaccine delivery. Despite this broad utility, the high cost of electroporators can keep this approach out of reach for many budget-conscious laboratories. To address this need, we develop a simple, inexpensive, and handheld electroporator inspired by and derived from a common household piezoelectric stove lighter. The proposed "ElectroPen" device can cost as little as 23 cents (US dollars) to manufacture, is portable (weighs 13 g and requires no electricity), can be easily fabricated using 3D printing, and delivers repeatable exponentially decaying pulses of about 2,000 V in 5 ms. We provide a proof-of-concept demonstration by genetically transforming plasmids into Escherichia coli cells, showing transformation efficiency comparable to commercial devices, but at a fraction of the cost. We also demonstrate the potential for rapid dissemination of this approach, with multiple research groups across the globe validating the ease of construction and functionality of our device, supporting the potential for democratization of science through frugal tools. Thus, the simplicity, accessibility, and affordability of our device holds potential for making modern synthetic biology accessible in high school, community, and resource-poor laboratories.
- 10 January 2020
- Published by Public Library of Science (PLoS) in PLOS Biology
- Vol. 18 (1) , e3000589
Open AccessElectroPen: An ultra-low–cost, electricity-free, portable electroporator
Electroporation is a basic yet powerful method for delivering small molecules (RNA, DNA, drugs) across cell membranes by application of an electrical field. It is used for many diverse applications, from genetically engineering cells to drug- and DNA-based vaccine delivery. Despite this broad utility, the high cost of electroporators can keep this approach out of reach for many budget-conscious laboratories. To address this need, we develop a simple, inexpensive, and handheld electroporator inspired by and derived from a common household piezoelectric stove lighter. The proposed "ElectroPen" device can cost as little as 23 cents (US dollars) to manufacture, is portable (weighs 13 g and requires no electricity), can be easily fabricated using 3D printing, and delivers repeatable exponentially decaying pulses of about 2,000 V in 5 ms. We provide a proof-of-concept demonstration by genetically transforming plasmids into Escherichia coli cells, showing transformation efficiency comparable to commercial devices, but at a fraction of the cost. We also demonstrate the potential for rapid dissemination of this approach, with multiple research groups across the globe validating the ease of construction and functionality of our device, supporting the potential for democratization of science through frugal tools. Thus, the simplicity, accessibility, and affordability of our device holds potential for making modern synthetic biology accessible in high school, community, and resource-poor laboratories.
- Open Access
- 21 May 2019
- Published by Public Library of Science (PLoS) in PLOS Biology
- Vol. 17 (5) , e3000251
A 3D-printed hand-powered centrifuge for molecular biology
The centrifuge is an essential tool for many aspects of research and medical diagnostics. However, conventional centrifuges are often inaccessible outside of standard laboratory settings, such as remote field sites, because they require a constant external power source and can be prohibitively costly in resource-limited settings and Science, technology, engineering, and mathematics (STEM)-focused programs. Here we present the 3D-Fuge, a 3D-printed hand-powered centrifuge, as a novel alternative to standard benchtop centrifuges. Based on the design principles of a paper-based centrifuge, this 3D-printed instrument increases the volume capacity to 2 mL and can reach hand-powered centrifugation speeds up to 6,000 rpm. The 3D-Fuge devices presented here are capable of centrifugation of a wide variety of different solutions such as spinning down samples for biomarker applications and performing nucleotide extractions as part of a portable molecular lab setup. We introduce the design and proof-of-principle trials that demonstrate the utility of low-cost 3D-printed centrifuges for use in remote field biology and educational settings.
- 21 May 2019
- Published by Public Library of Science (PLoS) in PLOS Biology
- Vol. 17 (5) , e3000251
Open AccessA 3D-printed hand-powered centrifuge for molecular biology
The centrifuge is an essential tool for many aspects of research and medical diagnostics. However, conventional centrifuges are often inaccessible outside of standard laboratory settings, such as remote field sites, because they require a constant external power source and can be prohibitively costly in resource-limited settings and Science, technology, engineering, and mathematics (STEM)-focused programs. Here we present the 3D-Fuge, a 3D-printed hand-powered centrifuge, as a novel alternative to standard benchtop centrifuges. Based on the design principles of a paper-based centrifuge, this 3D-printed instrument increases the volume capacity to 2 mL and can reach hand-powered centrifugation speeds up to 6,000 rpm. The 3D-Fuge devices presented here are capable of centrifugation of a wide variety of different solutions such as spinning down samples for biomarker applications and performing nucleotide extractions as part of a portable molecular lab setup. We introduce the design and proof-of-principle trials that demonstrate the utility of low-cost 3D-printed centrifuges for use in remote field biology and educational settings.