Irfan Khan
Research Subjects
Irfan Khan has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Elaheh Ahmadi
University of California, Santa Barbara
12 shared publications - Kamruzzaman Khan
Department of Electrical and Computer Engineering, University of California, Santa Barbara, CA 93106, USA
6 shared publications - I. K. M. Reaz Rahman
University of California, Berkeley
4 shared publications - Oguz Odabasi
Department of Electrical Engineering and Computer Science, University of California at Los Angeles, Los Angeles, CA, USA
4 shared publications - Quazi Deen Mohd Khosru
Bangladesh University of Engineering and Technology
4 shared publications - Harsh Rana
Department of Electrical Engineering and Computer Science, University of California at Santa Barbara, Santa Barbara, CA, USA
3 shared publications
Latest Publications
- Open Access
- 1 September 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Up to 300 °C DC-RF performance of N-polar Al-rich AlGaN channel HEMT grown by plasma-assisted molecular beam epitaxy
In this letter, a plasma-assisted molecular beam epitaxy-grown N-polar Al0.55Ga0.45N channel high-electron-mobility transistor was demonstrated to exhibit stable DC and RF performance at elevated temperatures. At 300 °C, the device showed improved electrical characteristics, including a channel contact resistance of 246 Ω mm, a maximum drain current of 37.4 mA/mm, and a transconductance of 4.7 mS/mm, while maintaining a stable threshold voltage of −5.4 V. Consequently, enhanced RF performance was achieved compared to room temperature, with the cutoff frequency (fT) and maximum oscillation frequency (fmax) increasing to 0.62 and 1.19 GHz, respectively, at 300 °C.
- 1 September 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (3)
Open AccessUp to 300 °C DC-RF performance of N-polar Al-rich AlGaN channel HEMT grown by plasma-assisted molecular beam epitaxy
In this letter, a plasma-assisted molecular beam epitaxy-grown N-polar Al0.55Ga0.45N channel high-electron-mobility transistor was demonstrated to exhibit stable DC and RF performance at elevated temperatures. At 300 °C, the device showed improved electrical characteristics, including a channel contact resistance of 246 Ω mm, a maximum drain current of 37.4 mA/mm, and a transconductance of 4.7 mS/mm, while maintaining a stable threshold voltage of −5.4 V. Consequently, enhanced RF performance was achieved compared to room temperature, with the cutoff frequency (fT) and maximum oscillation frequency (fmax) increasing to 0.62 and 1.19 GHz, respectively, at 300 °C.
- Open Access
- 1 June 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (6)
Enhancement of doping efficiency via polarization engineering in nitrogen-polar graded AlGaN grown by plasma-assisted molecular beam epitaxy
Efficient n-type doping in ultra-wide bandgap Al-rich AlGaN remains challenging due to deep silicon donor levels and strong self-compensation, which limit carrier activation. This article reports the demonstration of enhanced doping efficiency in nitrogen (N)-polar graded Al-rich AlxGa1−xN films grown on single-crystal AlN substrates by plasma-assisted molecular beam epitaxy, enabled by polarization induced doping in combination with Si doping. The optimized N-polar graded AlGaN films exhibited atomically smooth morphology with well-defined step edges. Room-temperature Hall measurements revealed a three-dimensional electron gas with a sheet density of 6.9 × 1012 cm−2 and a mobility of 37 cm2/(V s), with almost zero freeze-out down to 50 K. Upon 4 × 1018 cm−3 Si doping, the sheet and bulk electron concentrations increased to 2.3 × 1013 cm−2 and 4.42 × 1018 cm−3, respectively, at room temperature. No carrier freeze-out was observed in these films in the temperature range from 50 to 400 K. A low specific contact resistivity of 4.5 × 10−5 Ω cm2 was achieved using higher Si doping (1 × 1020 cm−3). This approach offers a promising path toward high-performance Al-rich AlGaN transistors.
- 1 June 2026
- Published by AIP Publishing in APL Materials
- Vol. 14 (6)
Open AccessEnhancement of doping efficiency via polarization engineering in nitrogen-polar graded AlGaN grown by plasma-assisted molecular beam epitaxy
Efficient n-type doping in ultra-wide bandgap Al-rich AlGaN remains challenging due to deep silicon donor levels and strong self-compensation, which limit carrier activation. This article reports the demonstration of enhanced doping efficiency in nitrogen (N)-polar graded Al-rich AlxGa1−xN films grown on single-crystal AlN substrates by plasma-assisted molecular beam epitaxy, enabled by polarization induced doping in combination with Si doping. The optimized N-polar graded AlGaN films exhibited atomically smooth morphology with well-defined step edges. Room-temperature Hall measurements revealed a three-dimensional electron gas with a sheet density of 6.9 × 1012 cm−2 and a mobility of 37 cm2/(V s), with almost zero freeze-out down to 50 K. Upon 4 × 1018 cm−3 Si doping, the sheet and bulk electron concentrations increased to 2.3 × 1013 cm−2 and 4.42 × 1018 cm−3, respectively, at room temperature. No carrier freeze-out was observed in these films in the temperature range from 50 to 400 K. A low specific contact resistivity of 4.5 × 10−5 Ω cm2 was achieved using higher Si doping (1 × 1020 cm−3). This approach offers a promising path toward high-performance Al-rich AlGaN transistors.
- Open Access
- 1 March 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
First demonstration of an N-polar high Al-content AlGaN channel HEMT grown by plasma-assisted molecular beam epitaxy
An N-polar Al0.65Ga0.35N/Al0.85Ga0.15N high electron mobility transistor (HEMT) was demonstrated on an AlN substrate. The epitaxial layers were grown by plasma-assisted molecular beam epitaxy (PAMBE), and a 3 nm in situ GaN cap was employed to prevent surface oxidation of the AlGaN channel. To reduce contact resistance, highly Si-doped, compositionally graded AlGaN was selectively regrown by PAMBE in the contact regions. Peak drain currents of 0.12 mA/mm at room temperature and 0.8 mA/mm at 300 °C were measured. Transconductance also increased from 53 μS/mm at room temperature to 262 μS/mm at 300 °C. Temperature-dependent Hall measurements indicated a reduction in channel resistance with increasing temperature, attributed to enhanced carrier density and mobility. A breakdown voltage of 95.8 V was obtained, along with a corresponding critical electric field of 2.74 MV/cm. While further improvements in current density are necessary for practical applications, this paper reports the first N-polar AlGaN channel HEMTs grown by PAMBE.
- 1 March 2026
- Published by AIP Publishing in APL Electronic Devices
- Vol. 2 (1)
Open AccessFirst demonstration of an N-polar high Al-content AlGaN channel HEMT grown by plasma-assisted molecular beam epitaxy
An N-polar Al0.65Ga0.35N/Al0.85Ga0.15N high electron mobility transistor (HEMT) was demonstrated on an AlN substrate. The epitaxial layers were grown by plasma-assisted molecular beam epitaxy (PAMBE), and a 3 nm in situ GaN cap was employed to prevent surface oxidation of the AlGaN channel. To reduce contact resistance, highly Si-doped, compositionally graded AlGaN was selectively regrown by PAMBE in the contact regions. Peak drain currents of 0.12 mA/mm at room temperature and 0.8 mA/mm at 300 °C were measured. Transconductance also increased from 53 μS/mm at room temperature to 262 μS/mm at 300 °C. Temperature-dependent Hall measurements indicated a reduction in channel resistance with increasing temperature, attributed to enhanced carrier density and mobility. A breakdown voltage of 95.8 V was obtained, along with a corresponding critical electric field of 2.74 MV/cm. While further improvements in current density are necessary for practical applications, this paper reports the first N-polar AlGaN channel HEMTs grown by PAMBE.
- 29 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Record-high electron mobility at near pinch-off in N-polar GaN HEMT structures grown on on-axis N-polar GaN substrates by plasma-assisted molecular beam epitaxy
In power amplifiers, achieving maximum drain efficiency requires deeper class-AB operation. Class-AB devices are biased near pinch-off, where the charge density is low. N-polar gallium nitride (GaN) high electron mobility transistors (HEMTs) have demonstrated exceptional performance, but they face a challenge of reduced electron mobility at low charge densities near pinch-off. This contrasts with conventional Ga-polar GaN HEMTs, where electron mobility increases as charge density decreases. In this work, we present an increase in electron mobility as charge density was reduced by applying a higher gate reverse bias in N-polar HEMT structures. The N-polar GaN HEMT structures presented here were grown on low-dislocation density on-axis N-polar GaN substrate using plasma-assisted molecular beam epitaxy (PAMBE). Epi-structures with different barrier materials, including InAlN and AlN/GaN digital alloy, were investigated. Electron mobility as a function of 2-dimensional electron gas (2DEG) density was extracted using a combination of the gated transfer length method and capacitance–voltage measurements. A record high mobility of 2000 and 6000 cm2/(V s) was achieved, at room temperature and 85 K, respectively, near pinch-off at a carrier density of 2.4 × 1012 cm−2. This study shows the potential of growth on on-axis substrates by PAMBE to improve efficiency in N-polar HEMTs.
- 29 September 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 127 (13)
Record-high electron mobility at near pinch-off in N-polar GaN HEMT structures grown on on-axis N-polar GaN substrates by plasma-assisted molecular beam epitaxy
In power amplifiers, achieving maximum drain efficiency requires deeper class-AB operation. Class-AB devices are biased near pinch-off, where the charge density is low. N-polar gallium nitride (GaN) high electron mobility transistors (HEMTs) have demonstrated exceptional performance, but they face a challenge of reduced electron mobility at low charge densities near pinch-off. This contrasts with conventional Ga-polar GaN HEMTs, where electron mobility increases as charge density decreases. In this work, we present an increase in electron mobility as charge density was reduced by applying a higher gate reverse bias in N-polar HEMT structures. The N-polar GaN HEMT structures presented here were grown on low-dislocation density on-axis N-polar GaN substrate using plasma-assisted molecular beam epitaxy (PAMBE). Epi-structures with different barrier materials, including InAlN and AlN/GaN digital alloy, were investigated. Electron mobility as a function of 2-dimensional electron gas (2DEG) density was extracted using a combination of the gated transfer length method and capacitance–voltage measurements. A record high mobility of 2000 and 6000 cm2/(V s) was achieved, at room temperature and 85 K, respectively, near pinch-off at a carrier density of 2.4 × 1012 cm−2. This study shows the potential of growth on on-axis substrates by PAMBE to improve efficiency in N-polar HEMTs.
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1505-1508
Enhancement Mode N-Polar Deep Recess GaN HEMT With Record Small Signal Performance
In this letter, we report a novel enhancement mode N-polar Deep Recess (NPDR) Gallium Nitride (GaN) High Electron Mobility Transistor (HEMT). Enhancement mode operation was achieved by recess etching with a combination of atomic layer etching (ALE) and wet etching. A high-k and high breakdown field HfSiO gate dielectric was employed. The epi-structure was grown on a low dislocation density on-axis N-polar GaN substrate by plasma-assisted molecular beam epitaxy (PAMBE). As a result, true normally-off operation with +0.8V threshold voltage, 1.5 A/mm peak saturation drain current, and 0.55 S/mm transconductance was achieved with 75 nm gate length (LG). A cutoff frequency (fT) of 122 GHz was measured, which resulted in a record fT*LG of 9.1 GHz $\cdot \mu $ m for E-mode AlGaN/GaN HEMTs. Load pull measurements demonstrated an output power of 2.7 W/mm and a power-added efficiency of 46% at 10 GHz.
- 3 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1505-1508
Enhancement Mode N-Polar Deep Recess GaN HEMT With Record Small Signal Performance
In this letter, we report a novel enhancement mode N-polar Deep Recess (NPDR) Gallium Nitride (GaN) High Electron Mobility Transistor (HEMT). Enhancement mode operation was achieved by recess etching with a combination of atomic layer etching (ALE) and wet etching. A high-k and high breakdown field HfSiO gate dielectric was employed. The epi-structure was grown on a low dislocation density on-axis N-polar GaN substrate by plasma-assisted molecular beam epitaxy (PAMBE). As a result, true normally-off operation with +0.8V threshold voltage, 1.5 A/mm peak saturation drain current, and 0.55 S/mm transconductance was achieved with 75 nm gate length (LG). A cutoff frequency (fT) of 122 GHz was measured, which resulted in a record fT*LG of 9.1 GHz $\cdot \mu $ m for E-mode AlGaN/GaN HEMTs. Load pull measurements demonstrated an output power of 2.7 W/mm and a power-added efficiency of 46% at 10 GHz.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (12) , 1335-1338
Demonstration of Normally-Off N-Polar GaN Deep Recess HEMT
In this letter, we report the first normally-off N-polar GaN deep recess high electron mobility transistor (HEMT). Utilizing atomic layer etching (ALE), followed by acid treatment, we achieved normally-off operation through gate recess etching on an N-polar GaN deep recess HEMT epitaxial structure, with metal–organic chemical vapor deposition (MOCVD) SiN $_{{{x}}}$ serving as the gate insulator. A threshold voltage of $+$ 0.5 V was attained, along with impressive metrics, such as low off-state drain leakage current (12 nA/mm), off-state gate leakage current (28 nA/mm), and on-state gate current (35 nA/mm). Remarkable performance parameters include a high on/off ratio of 5 $\times$ 10 $^{{\text{7}}}$ , drain off-state breakdown voltage of 53 V, and gate forward bias breakdown voltage of 5 V. Small signal measurements demonstrated a current-gain cutoff frequency ( $f_{{\text{T}}}$ ) and power-gain cutoff frequency ( $f_{\mathbf{MAX}}$ ) of 8.6 and 52.1 GHz, respectively, with a gate length of 0.6 $\mu $ m. Furthermore, a competitive output power density of 5.1 W/mm with 50% power added efficiency was achieved at 4 GHz. Results underscore the potential of normally-off N-polar GaN deep recess HEMTs for both RF and high-voltage applications.
- 14 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (12) , 1335-1338
Demonstration of Normally-Off N-Polar GaN Deep Recess HEMT
In this letter, we report the first normally-off N-polar GaN deep recess high electron mobility transistor (HEMT). Utilizing atomic layer etching (ALE), followed by acid treatment, we achieved normally-off operation through gate recess etching on an N-polar GaN deep recess HEMT epitaxial structure, with metal–organic chemical vapor deposition (MOCVD) SiN $_{{{x}}}$ serving as the gate insulator. A threshold voltage of $+$ 0.5 V was attained, along with impressive metrics, such as low off-state drain leakage current (12 nA/mm), off-state gate leakage current (28 nA/mm), and on-state gate current (35 nA/mm). Remarkable performance parameters include a high on/off ratio of 5 $\times$ 10 $^{{\text{7}}}$ , drain off-state breakdown voltage of 53 V, and gate forward bias breakdown voltage of 5 V. Small signal measurements demonstrated a current-gain cutoff frequency ( $f_{{\text{T}}}$ ) and power-gain cutoff frequency ( $f_{\mathbf{MAX}}$ ) of 8.6 and 52.1 GHz, respectively, with a gate length of 0.6 $\mu $ m. Furthermore, a competitive output power density of 5.1 W/mm with 50% power added efficiency was achieved at 4 GHz. Results underscore the potential of normally-off N-polar GaN deep recess HEMTs for both RF and high-voltage applications.
- Open Access
- 5 February 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (6)
Demonstration of controllable Si doping in N-polar AlN using plasma-assisted molecular beam epitaxy
In this study, we present the demonstration of controllable Si doping in N-polar AlN films grown on single-crystal AlN substrates by plasma-assisted molecular beam epitaxy. Through optimization of growth conditions, we obtained high-quality N-polar AlN films at 950 °C. However, our studies revealed that Si incorporation dramatically decreases at such high growth temperature. To enable higher Si incorporation, a hybrid low-temperature and high-temperature growth condition was developed by using Ga as a surfactant at low-temperature growth. By lowering the growth temperature of AlN to 750 °C, we were able to incorporate Si with concentrations as high as 2×1020 cm−3 and demonstrated an electron concentration as high as 1.25×1019 cm−3 at room temperature. The secondary ion mass spectrometry analysis revealed that, <0.2% Ga is incorporated in the AlN films grown with Ga as a surfactant at low temperature.
- 5 February 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 124 (6)
Open AccessDemonstration of controllable Si doping in N-polar AlN using plasma-assisted molecular beam epitaxy
In this study, we present the demonstration of controllable Si doping in N-polar AlN films grown on single-crystal AlN substrates by plasma-assisted molecular beam epitaxy. Through optimization of growth conditions, we obtained high-quality N-polar AlN films at 950 °C. However, our studies revealed that Si incorporation dramatically decreases at such high growth temperature. To enable higher Si incorporation, a hybrid low-temperature and high-temperature growth condition was developed by using Ga as a surfactant at low-temperature growth. By lowering the growth temperature of AlN to 750 °C, we were able to incorporate Si with concentrations as high as 2×1020 cm−3 and demonstrated an electron concentration as high as 1.25×1019 cm−3 at room temperature. The secondary ion mass spectrometry analysis revealed that, <0.2% Ga is incorporated in the AlN films grown with Ga as a surfactant at low temperature.
- Open Access
- 29 December 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (1) , 015027
Demonstration of 82% relaxed In0.18Ga0.82N on porous GaN pseudo-substrate by plasma-assisted molecular beam epitaxy
In this study, the impact of InGaN film thickness and different compositionally graded structures on InGaN relaxation grown on tiled GaN-on-porous-GaN pseudo substrates (PSs) were studied. In addition, the impact of the degree of porosification on the In incorporation and relaxation of InGaN were examined. 82% relaxed 1μm thick In0.18Ga0.82N, which is equivalent to a fully relaxed In-composition of 15%, on porous GaN PS was obtained. Additionally, multi-quantum wells (MQWs) grown on the MBE InGaN-on-porous GaN base layers by MOCVD showed ∼85 nm redshift in comparison with MQWs grown on planar GaN. The developed InGaN-on-porous-GaN PSs can provide an alternative route to grow MQW with a high In content which is essential for high-efficiency nitride-based red LEDs.
- 29 December 2023
- Published by IOP Publishing in Physica Scripta
- Vol. 99 (1) , 015027
Open AccessDemonstration of 82% relaxed In0.18Ga0.82N on porous GaN pseudo-substrate by plasma-assisted molecular beam epitaxy
In this study, the impact of InGaN film thickness and different compositionally graded structures on InGaN relaxation grown on tiled GaN-on-porous-GaN pseudo substrates (PSs) were studied. In addition, the impact of the degree of porosification on the In incorporation and relaxation of InGaN were examined. 82% relaxed 1μm thick In0.18Ga0.82N, which is equivalent to a fully relaxed In-composition of 15%, on porous GaN PS was obtained. Additionally, multi-quantum wells (MQWs) grown on the MBE InGaN-on-porous GaN base layers by MOCVD showed ∼85 nm redshift in comparison with MQWs grown on planar GaN. The developed InGaN-on-porous-GaN PSs can provide an alternative route to grow MQW with a high In content which is essential for high-efficiency nitride-based red LEDs.
- Open Access
- 14 November 2023
- Published by Taylor & Francis in Materials Research Letters
- Vol. 11 (12) , 1048-1054
Thermal conductivity enhancement of aluminum scandium nitride grown by molecular beam epitaxy
- 14 November 2023
- Published by Taylor & Francis in Materials Research Letters
- Vol. 11 (12) , 1048-1054
Open AccessThermal conductivity enhancement of aluminum scandium nitride grown by molecular beam epitaxy