José Reinaldo Moreira da Silva
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
José Reinaldo Moreira da Silva has a total of 57 co-authors. Here are the top co-authors by number of shared publications:
- Thawane Rodrigues Brito
Federal University of Lavras
4 shared publications - Anna Carolina de Almeida Andrade
Universidade Federal de Sergipe
3 shared publications - José Tarcísio Lima
Department of Forest Sciences, Federal University of Lavras, Lavras, Brazil
3 shared publications - Mônica Bezerra de Oliveira
Universidade Federal de Lavras, Brasil
3 shared publications - Paulo Ricardo Gherardi Hein
Federal University of Lavras, Brazil
3 shared publications - Ricardo Jorge Klitzke
Universidade Federal do Paraná
3 shared publications
Latest Publications
- 19 December 2023
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 27 (5) , 10059-10082
Log quality and lumber yield for export of five species from the Brazilian Amazon
- 19 December 2023
- Published by Springer Nature in Environment, Development and Sustainability
- Vol. 27 (5) , 10059-10082
Log quality and lumber yield for export of five species from the Brazilian Amazon
- Open Access
- 31 March 2023
- Published by Universidade Federal do Parana in FLORESTA
- Vol. 53 (2) , 129-135
PHYSICAL-MECHANICAL WOOD PROPERTIES FROM INVASIVE EXOTIC SPECIES OF ATLANTIC FOREST
Invasive exotic tree species cause several problems to the world biota. Removing these trees is important for restoring ecosystem balance. However, after the removal, there is a concern regarding the proper destination of the generated materials. The lack of knowledge about the wood characteristics makes it difficult to recommend for the most appropriate uses, which leads to a low added value of the product. The aim of the study was to assess the physical and mechanical wood properties and indicate the alternatives for using wood from exotic invasive species at the Fiocruz Mata Atlântica Biological Station, Rio de Janeiro - RJ. The three species studied were Artocarpus heterophyllus Lamarck (Jackfruit), Syzygium cumini (L.) Skeels (Java plum) and Clitoria fairchildiana R.A. Howard (Sombreiro). The physical and mechanical wood properties were determined in three distinct regions, denominated central, intermediate and external, ranging from pith-bark direction. The wood of Artocarpus heterophyllus had low basic density, retractions were lower in the central region, and the intermediate region had the highest mechanical resistance. The Syzygium cumini wood had medium density, the mechanical properties increased in the pith-bark direction, and the radial and volumetric retractions were lower in the central region. Clitoria fairchildiana wood had medium density and had the lowest mechanical resistance from the species evaluated. The three species have appropriate physical properties for the furniture sector, and the Syzygium cumini wood presented adequate mechanical resistance for civil construction.
- 31 March 2023
- Published by Universidade Federal do Parana in FLORESTA
- Vol. 53 (2) , 129-135
Open AccessPHYSICAL-MECHANICAL WOOD PROPERTIES FROM INVASIVE EXOTIC SPECIES OF ATLANTIC FOREST
Invasive exotic tree species cause several problems to the world biota. Removing these trees is important for restoring ecosystem balance. However, after the removal, there is a concern regarding the proper destination of the generated materials. The lack of knowledge about the wood characteristics makes it difficult to recommend for the most appropriate uses, which leads to a low added value of the product. The aim of the study was to assess the physical and mechanical wood properties and indicate the alternatives for using wood from exotic invasive species at the Fiocruz Mata Atlântica Biological Station, Rio de Janeiro - RJ. The three species studied were Artocarpus heterophyllus Lamarck (Jackfruit), Syzygium cumini (L.) Skeels (Java plum) and Clitoria fairchildiana R.A. Howard (Sombreiro). The physical and mechanical wood properties were determined in three distinct regions, denominated central, intermediate and external, ranging from pith-bark direction. The wood of Artocarpus heterophyllus had low basic density, retractions were lower in the central region, and the intermediate region had the highest mechanical resistance. The Syzygium cumini wood had medium density, the mechanical properties increased in the pith-bark direction, and the radial and volumetric retractions were lower in the central region. Clitoria fairchildiana wood had medium density and had the lowest mechanical resistance from the species evaluated. The three species have appropriate physical properties for the furniture sector, and the Syzygium cumini wood presented adequate mechanical resistance for civil construction.
- 20 December 2022
- Published by National Inquiry Services Center (NISC) in Southern Forests: a Journal of Forest Science
- Vol. 84 (4) , 320-324
Assessment of the acoustic change in heat-treated Pinus elliottii and Bertholletia excelsa wood from homogeneous plantations in Brazil
Heat treatment has been used in wood to improve its technological properties, but due to the complex nature of wood, it is necessary to carry out analyses to confirm the changes, and also to invest...
- 20 December 2022
- Published by National Inquiry Services Center (NISC) in Southern Forests: a Journal of Forest Science
- Vol. 84 (4) , 320-324
Assessment of the acoustic change in heat-treated Pinus elliottii and Bertholletia excelsa wood from homogeneous plantations in Brazil
Heat treatment has been used in wood to improve its technological properties, but due to the complex nature of wood, it is necessary to carry out analyses to confirm the changes, and also to invest...
- 20 December 2022
- Published by Instituto de Pesquisa e Estudos Florestais (IPEF) in Scientia Forestalis
- Vol. 50, 1-8
Effect of moisture and active ingredient concentration on CCA-C retention
The strategy of wood preservative treatment companies is to control the factors that influence retention, such as the concentration of the preservative solution and wood moisture, to reach values higher and closer to the standard minimum. The objective of this study was to reduce the consumption of Chromated Copper Arsenate type C (CCA-C) without affecting the quality of the treatment by determining the most efficient wood moisture interval for two genotypes of Eucalyptus sp. at different concentrations of active ingredients. A total of 54 fence posts of the species E. cloeziana and the hybrid E. camaldulensis x E. urophylla were treated. The pieces were randomly selected from three drying piles with different storage times in the yard (long, intermediate, and short). The active ingredient concentrations tested were 1.2, 1.4, and 1.6%. Retention analysis was performed to evaluate the quality of the preservative treatment. For both analyzed materials, the lowest and highest average retention values were observed in short and long storage piles and concentrations of 1.2% and 1.6% A.I. CCA-C, respectively. For E. cloeziana, only posts with a long storage time and treated with 1.6% of CCA-C were considered suitable for use in contact with the soil, according to the Brazilian standard, while for the clonal hybrid, posts with intermediate and long storage times, treated with 1.6% of CCA-C were considered suitable for use in contact with the soil. It was observed that CCA-C retention in the studied fence posts was directly influenced by the concentration of active ingredient in the preservative solution and by the storage time of the materials in the yard.
- 20 December 2022
- Published by Instituto de Pesquisa e Estudos Florestais (IPEF) in Scientia Forestalis
- Vol. 50, 1-8
Effect of moisture and active ingredient concentration on CCA-C retention
The strategy of wood preservative treatment companies is to control the factors that influence retention, such as the concentration of the preservative solution and wood moisture, to reach values higher and closer to the standard minimum. The objective of this study was to reduce the consumption of Chromated Copper Arsenate type C (CCA-C) without affecting the quality of the treatment by determining the most efficient wood moisture interval for two genotypes of Eucalyptus sp. at different concentrations of active ingredients. A total of 54 fence posts of the species E. cloeziana and the hybrid E. camaldulensis x E. urophylla were treated. The pieces were randomly selected from three drying piles with different storage times in the yard (long, intermediate, and short). The active ingredient concentrations tested were 1.2, 1.4, and 1.6%. Retention analysis was performed to evaluate the quality of the preservative treatment. For both analyzed materials, the lowest and highest average retention values were observed in short and long storage piles and concentrations of 1.2% and 1.6% A.I. CCA-C, respectively. For E. cloeziana, only posts with a long storage time and treated with 1.6% of CCA-C were considered suitable for use in contact with the soil, according to the Brazilian standard, while for the clonal hybrid, posts with intermediate and long storage times, treated with 1.6% of CCA-C were considered suitable for use in contact with the soil. It was observed that CCA-C retention in the studied fence posts was directly influenced by the concentration of active ingredient in the preservative solution and by the storage time of the materials in the yard.
- Open Access
- 26 September 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (13)
Specific cutting energy of Eucalyptus wood with different densities
The aim of the study was to evaluate how the specific cutting energy is influenced by the variation of the wood basic density in Eucalyptus spp. clones. Five clones, 10 years old, were used in the study: three hybrids of Eucalyptus grandis x Eucalyptus urophylla, one of Eucalyptus grandis and one of Eucalyptus urophylla. From each clone, five trees were cut down and divided into 2.0 m long logs. In two axial regions of the trunk (from 2.5 to 4.5 m and from 4.5 m to 6.5 m) the logs were cut into boards and reduced to specimens with dimensions of 660 x 110 x 21 mm. The basic density was determined by the hydrostatic method in two opposite wedges obtained from discs removed at 2.5, 4.5 and 6.5 m from the total height of the tree. To analyze the specific cutting energy, 10 specimens were selected for each axial region and clone. A frequency inverter was used to monitor the cutting process. Analysis of variance was applied to evaluate the specific cutting energy and the wood basic density. The results obtained appointed a significant difference between the woods of the clones for basic density and specific cutting energy. For the wood in the different axial regions, only the specific cutting energy was significant. Clone 1 required less specific cutting energy, as it was influenced by the lower basic density. In the 2.5 to 4.5 m axial region, a higher specific cutting energy was observed even with lower basic density.
- 26 September 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (13)
Open AccessSpecific cutting energy of Eucalyptus wood with different densities
The aim of the study was to evaluate how the specific cutting energy is influenced by the variation of the wood basic density in Eucalyptus spp. clones. Five clones, 10 years old, were used in the study: three hybrids of Eucalyptus grandis x Eucalyptus urophylla, one of Eucalyptus grandis and one of Eucalyptus urophylla. From each clone, five trees were cut down and divided into 2.0 m long logs. In two axial regions of the trunk (from 2.5 to 4.5 m and from 4.5 m to 6.5 m) the logs were cut into boards and reduced to specimens with dimensions of 660 x 110 x 21 mm. The basic density was determined by the hydrostatic method in two opposite wedges obtained from discs removed at 2.5, 4.5 and 6.5 m from the total height of the tree. To analyze the specific cutting energy, 10 specimens were selected for each axial region and clone. A frequency inverter was used to monitor the cutting process. Analysis of variance was applied to evaluate the specific cutting energy and the wood basic density. The results obtained appointed a significant difference between the woods of the clones for basic density and specific cutting energy. For the wood in the different axial regions, only the specific cutting energy was significant. Clone 1 required less specific cutting energy, as it was influenced by the lower basic density. In the 2.5 to 4.5 m axial region, a higher specific cutting energy was observed even with lower basic density.
- Open Access
- 13 May 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (7)
Influence of basic wood density on the specific cutting energy
The density of the wood influences directly on the quality of the surface, on the resistance to cutting as well as on the energy required for processing. The aim of this study was to obtain the association between specific cutting energies and basic wood densities in peripheral milling with the use of a computer numerical control. For this purpose, wood from nine species with a wide range of basic densities were used. The specimens were milled in a router with a CNC. Both the feeding and routing speeds were constant, and there was no source of variation among treatments. The values of specific energy were calculated taking into account the active power, the cutting time and the volume of wood removed. Results showed that there was a moderate correlation (r=0.61) between specific cutting energy and basic wood density data. However, by observing the particularities of each species, it was noticeable that the specific cutting energy varied as a result of factors such as the anatomical structure and the type of wood grain. It was concluded that the basic wood density has a positive correlation on the specific cutting energy required, yet it does not explain this relationship alone.
- 13 May 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (7)
Open AccessInfluence of basic wood density on the specific cutting energy
The density of the wood influences directly on the quality of the surface, on the resistance to cutting as well as on the energy required for processing. The aim of this study was to obtain the association between specific cutting energies and basic wood densities in peripheral milling with the use of a computer numerical control. For this purpose, wood from nine species with a wide range of basic densities were used. The specimens were milled in a router with a CNC. Both the feeding and routing speeds were constant, and there was no source of variation among treatments. The values of specific energy were calculated taking into account the active power, the cutting time and the volume of wood removed. Results showed that there was a moderate correlation (r=0.61) between specific cutting energy and basic wood density data. However, by observing the particularities of each species, it was noticeable that the specific cutting energy varied as a result of factors such as the anatomical structure and the type of wood grain. It was concluded that the basic wood density has a positive correlation on the specific cutting energy required, yet it does not explain this relationship alone.
- Open Access
- 9 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (4)
Influence of chromated copper arsenate type-C concentration on the quality of treated fence posts
This study aimed to reduce the concentration of chromated copper arsenate type-C (CCA-C) in preservative treatments of Eucalyptus sp. for use in applications with ground contact. The genetic materials used were Eucalyptus cloeziana of seminal origin and the clonal hybrid (E. urophylla x E. camaldulensis), which was derived from six year old crops at commercial plantations. The basic density, moisture content, percentage of sapwood, and wood treatable volume were determined, and the anatomical structures were characterized. The genetic materials were treated with concentrations of 1.2%, 1.3%, 1.4%, 1.5%, and 1.6% active ingredients (AI) of CCA-C. The quality of the preservative treatment was evaluated via penetration and retention tests. The treated wood volume of E. cloeziana exhibited 44% irregular partial penetration, 40% vascular penetration, 12% peripheral partial penetration, and 4% no penetration. For the hybrid, the wood volume exhibited 68% total penetration, 24% peripheral partial penetration, and 8% irregular partial penetration. The concentrations of 1.4% AI and 1.5% AI for E. cloeziana and of 1.4% AI and 1.6% AI for hybrid reached the minimum retention required by standard.
- 9 March 2022
- Published by Research, Society and Development in Research, Society and Development
- Vol. 11 (4)
Open AccessInfluence of chromated copper arsenate type-C concentration on the quality of treated fence posts
This study aimed to reduce the concentration of chromated copper arsenate type-C (CCA-C) in preservative treatments of Eucalyptus sp. for use in applications with ground contact. The genetic materials used were Eucalyptus cloeziana of seminal origin and the clonal hybrid (E. urophylla x E. camaldulensis), which was derived from six year old crops at commercial plantations. The basic density, moisture content, percentage of sapwood, and wood treatable volume were determined, and the anatomical structures were characterized. The genetic materials were treated with concentrations of 1.2%, 1.3%, 1.4%, 1.5%, and 1.6% active ingredients (AI) of CCA-C. The quality of the preservative treatment was evaluated via penetration and retention tests. The treated wood volume of E. cloeziana exhibited 44% irregular partial penetration, 40% vascular penetration, 12% peripheral partial penetration, and 4% no penetration. For the hybrid, the wood volume exhibited 68% total penetration, 24% peripheral partial penetration, and 8% irregular partial penetration. The concentrations of 1.4% AI and 1.5% AI for E. cloeziana and of 1.4% AI and 1.6% AI for hybrid reached the minimum retention required by standard.
- 30 April 2021
- Published by Taylor & Francis in Drying Technology
- Vol. 40 (10) , 2046-2057
Drying kinetics inEucalyptus urophyllawood: analysis of anisotropy and region of the stem
This study aimed to examine the drying in Eucalyptus wood in different directions and regions. Flow rates of free (FRFW), bound (FRBW), and total water were calculated in three directions. FRFW in the transversal direction demonstrated higher rates for the internal region. FRFW in the longitudinal direction was 1.7 times higher than in radial and 2.4 times higher than in tangential. FRBW in the tangential and radial directions was equal. FRFW was ∼14 times higher than FRBW. Correlations between FRFW and FRBW were inversely proportional. The results can help in the drying optimization of Eucalyptus and indicate parameters for its use in industries.
- 30 April 2021
- Published by Taylor & Francis in Drying Technology
- Vol. 40 (10) , 2046-2057
Drying kinetics inEucalyptus urophyllawood: analysis of anisotropy and region of the stem
This study aimed to examine the drying in Eucalyptus wood in different directions and regions. Flow rates of free (FRFW), bound (FRBW), and total water were calculated in three directions. FRFW in the transversal direction demonstrated higher rates for the internal region. FRFW in the longitudinal direction was 1.7 times higher than in radial and 2.4 times higher than in tangential. FRBW in the tangential and radial directions was equal. FRFW was ∼14 times higher than FRBW. Correlations between FRFW and FRBW were inversely proportional. The results can help in the drying optimization of Eucalyptus and indicate parameters for its use in industries.
- Open Access
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 45
QUALITY OF TROPICAL HARDWOOD FLOORS
This study aimed to determine the basic density of the wood and to simulate the performance of flooring produced with wood from five tropical species: Dipteryx odorata (Cumaru), Handroanthus spp. (Ipê), Hymenaea Courbaril (Jatobá), Astronium Lecointei (Muiracatiara), and Bowdichia virgilioides (Sucupira-Preta). Falling steel sphere, static and dynamic friction, indentation caused by loads applied in small areas, rolling load, and abrasiveness impact tests were simulated. The results were subjected to analysis of variance and Tukey’s test at 5% significance, and Pearson’s correlation was performed between the basic density and the indexes of each flooring. The basic density of the wood flooring made from the evaluated species ranged from 0.735 to 0.958 g.cm-3. D. odorata, Handroanthus spp. and H. courbaril woods were classified as heavy, while those of A. Lecointei and B. Virgilioides as moderately heavy. It was possible to indicate D. odorata, Handroanthus spp., H. courbaril, and B. Virgilioides flooring for environments with intense traffic where there is dragging or falling objects such as industries and companies. The A. Lecointei flooring can be used in residential environments with light traffic, where the loads exerted are low. There was a correlation between the basic wood density and the flooring use simulation tests.
- 1 January 2021
- Published by FapUNIFESP (SciELO) in Revista Árvore
- Vol. 45
Open AccessQUALITY OF TROPICAL HARDWOOD FLOORS
This study aimed to determine the basic density of the wood and to simulate the performance of flooring produced with wood from five tropical species: Dipteryx odorata (Cumaru), Handroanthus spp. (Ipê), Hymenaea Courbaril (Jatobá), Astronium Lecointei (Muiracatiara), and Bowdichia virgilioides (Sucupira-Preta). Falling steel sphere, static and dynamic friction, indentation caused by loads applied in small areas, rolling load, and abrasiveness impact tests were simulated. The results were subjected to analysis of variance and Tukey’s test at 5% significance, and Pearson’s correlation was performed between the basic density and the indexes of each flooring. The basic density of the wood flooring made from the evaluated species ranged from 0.735 to 0.958 g.cm-3. D. odorata, Handroanthus spp. and H. courbaril woods were classified as heavy, while those of A. Lecointei and B. Virgilioides as moderately heavy. It was possible to indicate D. odorata, Handroanthus spp., H. courbaril, and B. Virgilioides flooring for environments with intense traffic where there is dragging or falling objects such as industries and companies. The A. Lecointei flooring can be used in residential environments with light traffic, where the loads exerted are low. There was a correlation between the basic wood density and the flooring use simulation tests.
- Open Access
- 30 December 2020
- Published by Embrapa Florestas in Pesquisa Florestal Brasileira
- Vol. 40
Caracterização da madeira de Hovenia dulcis para a fabricação de pisos
Este trabalho teve como objetivo caracterizar a madeira de Hovenia dulcis Thunberg, visando sua utilização na fabricação de pisos. Para a caracterização tecnológica, foram utilizadas cinco árvores obtidas em Floresta Ombrófila Mista. As toras foram mensuradas, para a determinação do seu volume. Posteriormente, foi realizado o desdobro das mesmas em tábuas e blocos, para a determinação da massa específica básica, dureza Janka (tora da base) e ensaios de simulação de piso em serviço (toras do meio e topo). As tábuas e os blocos foram secos, para posterior preparação dos corpos de prova. Esses foram confeccionados separando-se a madeira constituída com 100% de cerne daquela que apresentava cerne e alburno. A madeira de H. dulcis caracterizou-se como de média massa específica (0,54 g cm-³), com média resistência (5.851,99 N). Em todos os testes de simulação de piso em serviço, a madeira de H. dulcis proporcionou resistência superior ou semelhante a outras espécies exóticas e inferior a espécies folhosas nativas encontradas na literatura. Concluiu-se que a madeira em estudo apresenta baixa resistência para esforços máximos, podendo ser utilizada em pisos para trânsito leve ou em locais em que as cargas são baixas.
- 30 December 2020
- Published by Embrapa Florestas in Pesquisa Florestal Brasileira
- Vol. 40
Open AccessCaracterização da madeira de Hovenia dulcis para a fabricação de pisos
Este trabalho teve como objetivo caracterizar a madeira de Hovenia dulcis Thunberg, visando sua utilização na fabricação de pisos. Para a caracterização tecnológica, foram utilizadas cinco árvores obtidas em Floresta Ombrófila Mista. As toras foram mensuradas, para a determinação do seu volume. Posteriormente, foi realizado o desdobro das mesmas em tábuas e blocos, para a determinação da massa específica básica, dureza Janka (tora da base) e ensaios de simulação de piso em serviço (toras do meio e topo). As tábuas e os blocos foram secos, para posterior preparação dos corpos de prova. Esses foram confeccionados separando-se a madeira constituída com 100% de cerne daquela que apresentava cerne e alburno. A madeira de H. dulcis caracterizou-se como de média massa específica (0,54 g cm-³), com média resistência (5.851,99 N). Em todos os testes de simulação de piso em serviço, a madeira de H. dulcis proporcionou resistência superior ou semelhante a outras espécies exóticas e inferior a espécies folhosas nativas encontradas na literatura. Concluiu-se que a madeira em estudo apresenta baixa resistência para esforços máximos, podendo ser utilizada em pisos para trânsito leve ou em locais em que as cargas são baixas.