Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Aqeel Hussain Naqvi has a total of 24 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A Testbed for Molecular Communication using a Microfluidic Device with Fluorescent Nanoparticles

    by Aqeel Hussain Naqvi, Bige Deniz Unluturk

    Unlike existing technologies, a new communication technique that fits well in nano- and micro-sized scenarios is molecular communication (MC). Inspired by nature, MC relies on the exchange of molecules for the transfer of information. This work describes a molecular multiple-input multiple-out (MIMO) communication platform based on a microfluidic device and an optical detection system. We demonstrate an MC platform that uses fluorescent beads as messenger molecules to transport encoded information in microfluidic channels via flow-induced diffusion. Programmable syringe pumps acting as transmitters transmit fluorescent beads into the microchannels, and the fluorescence microscope records the signal at the receiver end. This microfluidic platform can be used as an experimental testbed for molecular communication and will pave the way for providing a chassis to study molecular communication at the interface of biology.


  • Open Access

    1-Bit Transmission-Type Digital Programmable Coding Metasurface with Multi-Functional Beam-Shaping Capability for Ka-Band Applications

    by Aqeel Hussain Naqvi, Duc Anh Pham, Syed Imran Hussain Shah, Sungjoon Lim

    Digital programmable coding metasurfaces (DPCMs) have recently attracted enormous attention and have been broadly applied, owing to their ability to manipulate electromagnetic (EM) wave behaviours and programmable multi-functionality. Recent DPCM works are divided into reflection and transmission types (R-DPCM and T-DPCM, respectively); however, there are only a few reported T-DPCM works in the millimetre-wave spectrum, owing to the difficulty of realising the large-phase controllable range while maintaining low transmission losses with electronic control components. Consequently, most millimetre-wave T-DPCMs are demonstrated only with limited functions in a single design. Additionally, all these designs use high-cost substrate materials that constrain practical applicability, owing to cost-ineffectiveness. Herein, we propose a 1-bit T-DPCM that simultaneously performs three dynamic beam-shaping functions with a single structure for millimetre-wave applications. The proposed structure is completely constructed using low-cost FR-4 materials, and operation of each meta-cell is manipulated using PIN-diodes, thus driving the achievement of multiple effective dynamic functionalities including dual-beam scanning, multi-beam shaping, and orbital-angular-momentum-mode generation. It should be noted that there are no reported millimetre-wave T-DPCMs demonstrating multi-function design, thus showing a gap in the recent literature of millimetre-wave T-DPCMs. Moreover, cost-effectiveness can be significantly enhanced, owing to the construction of the proposed T-DPCM using only low-cost material.


  • Open Access

    Hydrodynamic metasurface for programming electromagnetic beam scanning on the Azimuth and elevation planes

    by Aqeel Hussain Naqvi, Sungjoon Lim

    The development of multifunctional and reconfigurable metasurfaces capable of manipulating electromagnetic waves has created new opportunities for various exciting applications. Extensive efforts have been applied to exploiting active metasurfaces with properties that can be controlled by externally controlling active components. However, previous approaches have poor switch isolation, power handling limitations due to nonlinear effects, and complex biasing networks. Therefore, dynamically tunable metasurfaces have become a burgeoning field in many research areas. This paper reports a hydrodynamic metasurface (HMS) that can be programmed to realize electromagnetic beam scanning on the azimuth and elevation planes. The proposed HMS platform incorporates four micropumps, each controlling four metasurface elements via microfluidic channels, built into the HMS base. The proposed platform regulates microfluidic flow through micropumps, causing irregularities in incident wave transmission phase. An HMS was built as a proof of concept, and far-field scanning experiments were performed. Numerical and experimental results verify the feasibility of electromagnetic beam scanning using a hydrodynamic metasurface. This work advances metasurface research, with very high potential for wide-ranging application and a promising route for replacing bulky cascading active components.


  • Open Access

    A Flexible and Pattern Reconfigurable Antenna with Small Dimensions and Simple Layout for Wireless Communication Systems Operating over 1.65–2.51 GHz

    by Adnan Ghaffar, Xue Jun Li, Wahaj Abbas Awan, Aqeel Hussain Naqvi, Niamat Hussain, Mohammad Alibakhshikenari, Ernesto Limiti

    This research article proposes a compact frequency and pattern reconfigurable flexible antenna for heterogeneous applications. A triangular monopole antenna with a semicircular stub is made frequency and pattern tunable by connecting and disconnecting two inverted L-shaped stubs utilizing diodes. When either of the stubs is connected to the radiator, a relative phase difference happens at both ends of the radiator that changes the direction of the electromagnetic radiations, consequently pattern reconfigurability can be obtain. Besides that, because of the reactive load introduced by the stubs, the antenna’s effective length has changed and, as a result, the frequency reconfigurability can be attained. The antenna features a compact size of 40 × 50 × 0.254 mm3 corresponding to 0.22λo × 0.27λo × 0.001λo, where λo is free-space wavelength at 1.65 GHz, while its operational bandwidth is from 1.65 GHz to 2.51 GHz, with an average gain and radiation efficiency of better than 2.2 dBi and 80%, exhibiting a pattern reconfigurability of 180° in the E-plane. The frequency of the proposed antenna can be switched from 2.1 GHz to 1.8 GHz by switching the state of both diodes in OFF and ON-state, respectively. The fabricated prototype of the antenna is tested to verify its performance parameters. In addition, to validate the proposed design, it has been compared with prior arts in terms of the overall size, reconfigurability type, flexibility, radio frequency (RF) switch type used for reconfigurability, and frequency bandwidth. The proposed antenna provides smaller size with a large bandwidth coverage alongside with discrete RF switch type with the advantages of flexibility and both frequency and pattern reconfigurability. As a result, the proposed compact flexible and pattern reconfigurable antenna is a promising candidate for heterogeneous applications, including the global system for mobile (GSM) band (1800 and 1900 MHz) and industrial, scientific and medical (ISM) band (2.4 GHz) along with well-known cellular communication bands of 3G, 4G, and long term evolution (LTE) bands ranging from 1700–2300 MHz around the globe.


  • Open Access

    Complementary Split-Ring Resonator (CSRR)-Loaded Sensor Array to Detect Multiple Cracks: Shapes, Sizes, and Positions on Metallic Surface

    by Ahmed Salim, Aqeel Hussain Naqvi, Anh Duc Pham, Sungjoon Lim

    Single-resonance-based radio frequency (RF) resonators cannot detect multiple cracks simultaneously nor localize the position of a crack. To address these drawbacks, we propose a complementary split-ring resonator (CSRR)-loaded array. In this array, there are four channels and each channel consists of three CSRRs, forming a 4×3 sensing array that is developed in the ground plane of a microstrip line using a low-cost FR4 substrate. A voltage-controlled oscillator (VCO) generates three discrete frequencies: 1.88 GHz, 2.60 GHz, and 3.61 GHz to each channel, which is sequentially selected using a single-pole four-throw (SP4T) switch. The transmitted RF signals are converted into the DC voltage levels and are interpreted by a microcontroller. Aluminum sheets with cracks embedded in the surface are used to demonstrate the detection of cracks of various shapes, sizes and locations/orientations (horizontal, diagonal, and vertical) with simulations and measurements. The detection of the minimum detectable crack (Wc×Lc×Dc = 1 mm × 10 mm × 0.1 mm) is experimentally verified. Full-length longer cracks (Lc = 100 mm) are also detected using our proposed detection system with the SP4T switch in addition to our proposed algorithm that scans the CSRRs of each selected channel.


  • (40 to 65) GHz Higher Order Mode Microstrip-Based Dual Band Dual Beam Tunable Leaky-Wave Antenna for Millimeter Wave Applications

    by Anirban Sarkar, Aqeel Hussain Naqvi, Sungjoon Lim

    This paper proposes a microstrip leaky-wave antenna with dual symmetrical side beams for complete V-band radiation coverage. Frequency sweeping dual beam scanning is obtained from 50–65 GHz due to wideband excitation for the microstrip second higher order mode. Appropriate metallic via hole placement realized a back-to-back half-mode pair, which can also generate two symmetrical side beams in the E-plane with enhanced gain within 40–55 GHz. Mode switching was achieved electronically by incorporating PIN diodes with a proper biasing network. The final antenna design was prototyped to validate the design concept. The leaky band in microstrip higher order modes was analyzed by dispersion characteristics and Bloch impedance. Operating frequency range and scanning range in the H-plane were obtained from 50–65 GHz with 12°–80° for unbiased and 41–53 GHz with 20.4–76° for biased states, respectively. The antenna exhibited measured 10 dB return loss bandwidth of 26% and 27.65%, and peak gain of 19 and 18.6 dBi, for the two states respectively with average side lobe level of <-15 dB and minimum cross polarization of 25 dB. Simulated results agreed well with the experimental data, validating this single layered structure for millimeter-wave wireless applications.


  • Open Access

    Via-Monopole Based Quasi Yagi-Uda Antenna for W-Band Applications using Through Glass Silicon via (TGSV) Technology

    by Aqeel Hussain Naqvi, Jeong-Heum Park, Chang-Wook Baek, Sungjoon Lim

    This paper presents a W-band planar type via-monopole based quasi Yagi-Uda antenna using metal coated through glass silicon via structures. The antenna was designed and fabricated on 350 μm thick borosilicate glass substrate, which has very low dielectric loss compared with silicon at millimeterwave frequencies. We used a microstrip line to feed the antenna, and the Yagi-Uda configuration using via structured radiator; reflectors; and director were fabricated using tungsten coated silicon via structures embedded in reflowed glass substrate with good high frequency characteristics. The proposed antenna achieved vertical polarization in planar configuration with height 0.09λo. High gain with end-fire radiation was achieved due to the Yagi-Uda configuration. Measured results confirmed the fabricated antenna operated in the W-band with 10 dB fractional bandwidth (FBW) of 12.5% from 76.3 to 86.5 GHz and peak gain of 7.82 dBi at 81 GHz in the end-fire direction. Thus, the proposed antenna with end-fire radiation will be useful for millimeter-wave onboard wireless communication, radar imaging, and tracking applications.


  • Open Access

    An Integrated Antenna System for 4G and Millimeter-Wave 5G Future Handheld Devices

    by Syeda I. Naqvi, Aqeel H. Naqvi, Farzana Arshad, Muhammad A. Riaz, Muhammad A. Azam, Mansoor S. Khan, Yasar Amin, Jonathan Loo, Hannu Tenhunen

    In this work, an integrated antenna system with Defected Ground Structure (DGS) is presented for Fourth Generation (4G) and millimeter (mm)-wave Fifth Generation (5G) wireless applications and handheld devices. The proposed design with overall dimensions of 110 mm × 75 mm is modeled on 0.508 mm thick Rogers RT/Duroid 5880 substrate. Radiating structure consists of antenna arrays excited by the T-shape 1 × 2 power divider/combiner. Dual bands for 4G centered at 3.8 GHz and 5.5 GHz are attained, whereas the 10-dB impedance bandwidth of 24.4 -29.3 GHz is achieved for the 5G antenna array. In addition, a peak gain of 5.41 dBi is demonstrated across the operating bandwidth of the 4G antenna array. Similarly, for the 5G mm-wave configuration the attained peak gain is 10.29 dBi. Moreover, significant isolation is obtained between the two antenna modules ensuring efficient dualfrequency band operation using a single integrated solution. To endorse the concept, antenna prototype is fabricated and far-field measurements are procured. Simulated and measured results exhibit coherence. Also the proposed design is investigated for the beam steering capability of the mm-wave 5G antenna array using CST®MWS®. The demonstrated structure offers various advantages including compactness, wide bandwidth, high gain, and planar configuration. Hence, the attained radiation characteristics prove the suitability of the proposed design for the current and future wireless handheld devices.


  • Fluidically Beam-Steering Metasurfaced Antenna

    by Aqeel Hussain Naqvi, Sungjoon Lim

    This paper presents a fluidically beam-steering metasurfaced antenna. The proposed antenna consists of a source antenna and a bi-layered metasurface which acts as partially reflecting surface (PRS) as a superstrate. The top-layer metasurface composed of 4×4 conductive squared ring element array on the top side of thin dielectric substrate and a 3-D printed bottom-layer for fluid movement. Radiation beam has been steered by means of water as a fluid flow in the different channels inside the bottom layer of metasurface. A 2-D beam-steering of ±15° in theta axis with 10-dB impedance bandwidth of 2.54-2.68 GHz has been achieved. Stable radiation gain of more than 5-dBi has been demonstrated across the operating bandwidth. The proposed antenna is low cost, low profile and can be used in systems for radiation diverse applications where the periodic metasurface structures are needed.


  • Open Access

    V-Band End-Fire Radiating Planar Micromachined Helical Antenna Using Through-Glass Silicon Via (TGSV) Technology

    by Aqeel Hussain Naqvi, Jeong-Heum Park, Chang-Wook Baek, Sungjoon Lim

    In this paper, we demonstrate a V-band planar micromachined helical antenna (PHA) with end-fire radiation on the glass substrate. The planar rectangular helical configuration is realized using the novel through-glass silicon via (TGSV) technology. The proposed micromachined antenna is designed and fabricated on a borosilicate glass substrate of thickness 350 lm, which has a very low dielectric loss compared to silicon at millimeter-wave bands. The proposed PHA is fed by a microstrip line, and the planar helical configuration with 3.25 turns is designed with 7 tungsten-coated silicon vias and 6 connected gold arm patterns, which are fabricated using the TGSV technology. Simulated and measured results show that the proposed antenna have a wide operational bandwidth of 50.3 to 65 GHz for |S11| < &–10 dB with a fractional bandwidth (FBW) of 25.5%. The measured peak gain is 6.3 dBi at 58 GHz. The proposed planar antenna with end-fire radiation is useful for millimeter-wave on-board wireless communication, radar imaging and tracking applications.