Zhongan Jiang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhongan Jiang has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Ya Peng
Univ Sci & Technol Beijing, Sch Civil & Resource Engn, Beijing 100083, Peoples R China
4 shared publications - Jihe Chen
School of Civil and Resource Engineering, University of Science and Technology Beijing, No. 30 Xueyuan Road, Haidian District, Beijing 100083, China
3 shared publications Jiuzhu Wang
School of Civil and Resources Engineering, University of Science and Technology Beijing, 30 Xueyuan Road, Haidian District, Beijing 100083, China
3 shared publicationsJu-Shi Chen
School of Civil and Resource Engineering, University of Science and Technology Beijing, Beijing, 100083, China
3 shared publicationsJushi Chen
3 shared publicationsYapeng Wang
3 shared publications
Latest Publications
- Open Access
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Virtual measurement of network-wide roadway wind-resistance changes from sparse airflow observations in mine ventilation networks
Accurate roadway wind resistance is essential for mine-ventilation calculation and airflow regulation, yet network-wide resistance measurement is difficult because only a limited number of roadways can be instrumented simultaneously. This study proposes a virtual measurement method for estimating network-wide roadway wind-resistance changes from sparse airflow observations. A global multilayer perceptron (Global MLP) first learns the principal nonlinear mapping from observed airflow and measurement masks to the complete resistance-change field, while a scaled and regularized GraphSAGE residual branch uses roadway connectivity to refine remaining local errors. The method was evaluated on a real-mine-derived and simulation-expanded dataset containing 6,374 valid scenarios and 645 unified roadways. Under the representative 30% sensing condition, airflow was observed in 194 roadways while resistance changes were estimated for all 645 roadways. The topology-residual estimator achieved an RMSE of 0.0544 and an R2 of 0.907, compared with 0.0556 and 0.903 for the Global MLP. Its global RMSE improvement was moderate, but roadway-level and upper-tail errors were reduced more consistently. Validation-calibrated marginal prediction intervals remained close to the nominal 90% and 95% coverage levels and were 44.4% and 50.2% narrower than those of Global MLP, respectively. Under 5% airflow-measurement noise, the estimator retained an RMSE of 0.0596 and a 95th-percentile absolute error of 0.0063. These results support network-wide wind-resistance virtual measurement from sparse airflow observations while showing that topology-related gains are sensing-dependent and marginal coverage is not uniform across target magnitudes.
- 28 August 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessVirtual measurement of network-wide roadway wind-resistance changes from sparse airflow observations in mine ventilation networks
Accurate roadway wind resistance is essential for mine-ventilation calculation and airflow regulation, yet network-wide resistance measurement is difficult because only a limited number of roadways can be instrumented simultaneously. This study proposes a virtual measurement method for estimating network-wide roadway wind-resistance changes from sparse airflow observations. A global multilayer perceptron (Global MLP) first learns the principal nonlinear mapping from observed airflow and measurement masks to the complete resistance-change field, while a scaled and regularized GraphSAGE residual branch uses roadway connectivity to refine remaining local errors. The method was evaluated on a real-mine-derived and simulation-expanded dataset containing 6,374 valid scenarios and 645 unified roadways. Under the representative 30% sensing condition, airflow was observed in 194 roadways while resistance changes were estimated for all 645 roadways. The topology-residual estimator achieved an RMSE of 0.0544 and an R2 of 0.907, compared with 0.0556 and 0.903 for the Global MLP. Its global RMSE improvement was moderate, but roadway-level and upper-tail errors were reduced more consistently. Validation-calibrated marginal prediction intervals remained close to the nominal 90% and 95% coverage levels and were 44.4% and 50.2% narrower than those of Global MLP, respectively. Under 5% airflow-measurement noise, the estimator retained an RMSE of 0.0596 and a 95th-percentile absolute error of 0.0063. These results support network-wide wind-resistance virtual measurement from sparse airflow observations while showing that topology-related gains are sensing-dependent and marginal coverage is not uniform across target magnitudes.
- Open Access
Variable-Frequency Ventilation Monitoring System Based on Collaborative Wind Speed Prediction Using Environmental Parameters
In order to predict the wind speed of the excavation roadway, control the frequency conversion operation of the local fan in real-time, and realize the real-time monitoring, collaborative prediction, and frequency conversion control of the ventilation state of the excavation face, the frequency conversion ventilation control system of the excavation face is designed. Based on the theory of frequency conversion control, the genetic-neural network wind speed prediction optimization model was established, and the frequency conversion ventilation control system of the excavation face was designed by using S7-200 SMART PLC. The system test results show that the genetic-neural network optimization model can collaboratively predict wind speed according to the environmental parameters (dust concentration, methane concentration, temperature, and humidity, etc.) of different working conditions. The frequency conversion ventilation control system realizes the real-time monitoring of the environmental parameters of the excavation surface, and also provides two control modes: automatic and manual. Compared with the traditional constant power frequency control fan wind speed, the PID wind speed closed-loop control technology can control the fan wind speed by frequency conversion, so that the actual wind speed of the roadway continues to approach the predicted value stably. The variable frequency ventilation control system can be widely used in different types of mines to realize the adaptive control response of ventilation equipment.
Open AccessVariable-Frequency Ventilation Monitoring System Based on Collaborative Wind Speed Prediction Using Environmental Parameters
In order to predict the wind speed of the excavation roadway, control the frequency conversion operation of the local fan in real-time, and realize the real-time monitoring, collaborative prediction, and frequency conversion control of the ventilation state of the excavation face, the frequency conversion ventilation control system of the excavation face is designed. Based on the theory of frequency conversion control, the genetic-neural network wind speed prediction optimization model was established, and the frequency conversion ventilation control system of the excavation face was designed by using S7-200 SMART PLC. The system test results show that the genetic-neural network optimization model can collaboratively predict wind speed according to the environmental parameters (dust concentration, methane concentration, temperature, and humidity, etc.) of different working conditions. The frequency conversion ventilation control system realizes the real-time monitoring of the environmental parameters of the excavation surface, and also provides two control modes: automatic and manual. Compared with the traditional constant power frequency control fan wind speed, the PID wind speed closed-loop control technology can control the fan wind speed by frequency conversion, so that the actual wind speed of the roadway continues to approach the predicted value stably. The variable frequency ventilation control system can be widely used in different types of mines to realize the adaptive control response of ventilation equipment.
- Open Access
- 20 May 2026
- Published by MDPI AG in Atmosphere
- Vol. 17 (5) , 524
Factors Influencing Inversion Layers and Subsequent Dust Transport in Deep Open-Pit Mines
Due to their unique topography, deep open-pit coal mines are prone to temperature inversions, which, in turn, exacerbate dust pollution. To characterize this phenomenon, we combined field measurements with FLUENT-based numerical simulations to analyze how inversion layer properties and dust transport patterns respond to varying conditions. The results show that the temperature contrast between the pit walls is positively correlated with the inversion layer’s temperature difference, thickness, and strength. In contrast, ambient wind speed is negatively correlated with the layer’s temperature difference and strength, yet positively correlated with its thickness. Surface temperature has no significant effect on the inversion layer’s temperature difference or thickness and exhibits only a weak correlation with its strength. Furthermore, higher wall temperature contrasts lead to increased dust concentration, whereas stronger winds promote dispersion and lower concentrations. These findings confirm that temperature inversion intensifies pollution, with stronger inversions causing more severe contamination. Therefore, mitigating the formation of inversion layers is crucial for effective dust control in deep pits. Unlike previous phenomenological observations, this study provides novel quantitative data on the thermal-aerodynamic coupling within deep open pits. Specifically, it establishes exact mathematical correlations between discrete rock wall temperature differentials and inversion layer thickness, providing critical thresholds for predicting severe dust retention.
- 20 May 2026
- Published by MDPI AG in Atmosphere
- Vol. 17 (5) , 524
Open AccessFactors Influencing Inversion Layers and Subsequent Dust Transport in Deep Open-Pit Mines
Due to their unique topography, deep open-pit coal mines are prone to temperature inversions, which, in turn, exacerbate dust pollution. To characterize this phenomenon, we combined field measurements with FLUENT-based numerical simulations to analyze how inversion layer properties and dust transport patterns respond to varying conditions. The results show that the temperature contrast between the pit walls is positively correlated with the inversion layer’s temperature difference, thickness, and strength. In contrast, ambient wind speed is negatively correlated with the layer’s temperature difference and strength, yet positively correlated with its thickness. Surface temperature has no significant effect on the inversion layer’s temperature difference or thickness and exhibits only a weak correlation with its strength. Furthermore, higher wall temperature contrasts lead to increased dust concentration, whereas stronger winds promote dispersion and lower concentrations. These findings confirm that temperature inversion intensifies pollution, with stronger inversions causing more severe contamination. Therefore, mitigating the formation of inversion layers is crucial for effective dust control in deep pits. Unlike previous phenomenological observations, this study provides novel quantitative data on the thermal-aerodynamic coupling within deep open pits. Specifically, it establishes exact mathematical correlations between discrete rock wall temperature differentials and inversion layer thickness, providing critical thresholds for predicting severe dust retention.
- Open Access
- 26 March 2025
- Published by MDPI AG in Atmosphere
- Vol. 16 (4) , 379
A Numerical Study on the Design of a Diffuser Nozzle for Pulsed-Jet Cleaning of Cone Filter Cartridges
For workplaces where the dust cakes have high viscosity, it is difficult to peel the dust cake from the surface of the dust filter cartridge. The problem of poor dust removal restricts the efficient and stable operation of the dust collector. This study proposes a diffuser nozzle to improve the pulsed-jet cleaning performance of cone filter cartridges. Through numerical modeling, the study investigates the improvement of pulsed-jet velocity and pressure by the diffuser nozzle, explores the influence of the diffuser angle (θ) and diffuser distance (D) on the jet field of the cone filter cartridge core, and compares the pulsed-jet intensity and uniformity of the dust removal filter cartridge. The findings show that the diffuser nozzle with appropriate parameters is conducive to enhancing the divergence and entrainment of the jet airflow, reducing the airflow velocity in the filter cartridge opening area and increasing the static pressure, while also increasing the airflow entrainment. The pulsed-jet intensity and uniformity, especially the pulsed-jet intensity in the upper part of the filter cartridge, vary significantly with θ or D, and the action mechanisms of θ or D are obtained. Under the recommended diffuser nozzle parameters (θ = 70° and D = 40 mm), the pulsed-jet intensity is 1086 Pa, which is 5.4% higher than that under the condition of the common round nozzle; the uniformity coefficient is 0.14, which is 60.0% better than that under the condition of the common round nozzle. For the upper part of the filter cartridge, the pulsed-jet intensity is 1.39 times that with the common nozzle. The result is significant as it offers a guide for improving the pulse-jet cleaning of dust removal filter cartridges.
- 26 March 2025
- Published by MDPI AG in Atmosphere
- Vol. 16 (4) , 379
Open AccessA Numerical Study on the Design of a Diffuser Nozzle for Pulsed-Jet Cleaning of Cone Filter Cartridges
For workplaces where the dust cakes have high viscosity, it is difficult to peel the dust cake from the surface of the dust filter cartridge. The problem of poor dust removal restricts the efficient and stable operation of the dust collector. This study proposes a diffuser nozzle to improve the pulsed-jet cleaning performance of cone filter cartridges. Through numerical modeling, the study investigates the improvement of pulsed-jet velocity and pressure by the diffuser nozzle, explores the influence of the diffuser angle (θ) and diffuser distance (D) on the jet field of the cone filter cartridge core, and compares the pulsed-jet intensity and uniformity of the dust removal filter cartridge. The findings show that the diffuser nozzle with appropriate parameters is conducive to enhancing the divergence and entrainment of the jet airflow, reducing the airflow velocity in the filter cartridge opening area and increasing the static pressure, while also increasing the airflow entrainment. The pulsed-jet intensity and uniformity, especially the pulsed-jet intensity in the upper part of the filter cartridge, vary significantly with θ or D, and the action mechanisms of θ or D are obtained. Under the recommended diffuser nozzle parameters (θ = 70° and D = 40 mm), the pulsed-jet intensity is 1086 Pa, which is 5.4% higher than that under the condition of the common round nozzle; the uniformity coefficient is 0.14, which is 60.0% better than that under the condition of the common round nozzle. For the upper part of the filter cartridge, the pulsed-jet intensity is 1.39 times that with the common nozzle. The result is significant as it offers a guide for improving the pulse-jet cleaning of dust removal filter cartridges.
- 1 April 2022
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 44, 8-19
Effect of inlet area on the performance of a two-stage cyclone separator
- 1 April 2022
- Published by Elsevier in Chinese Journal of Chemical Engineering
- Vol. 44, 8-19
Effect of inlet area on the performance of a two-stage cyclone separator
- 11 May 2021
- Published by Springer Nature in Journal of Central South University
- Vol. 28 (5) , 1342-1356
Ventilation control of tunnel drilling dust based on numerical simulation
- 11 May 2021
- Published by Springer Nature in Journal of Central South University
- Vol. 28 (5) , 1342-1356
Ventilation control of tunnel drilling dust based on numerical simulation
- 30 September 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (40) , 25832-25840
Study on Gas Diffusion in Fire Working Areas of Oil and Gas Pipelines Based on Temperature Difference
When a pipeline is under fire safety work construction, the stack effect of the pipeline will increase the diffusion rate of nitrogen, reduce the oxygen content, and cause asphyxia. To prove the influence of the stack effect of the pipeline on the nitrogen movement in the pipeline and put forward effective ventilation control measures, the formation mechanism, gas diffusion law, and ventilation parameters of the stack effect of the oil and gas pipelines are studied through theoretical derivation and numerical simulation. The results show that the nitrogen concentration at the height of the breathing zone in the hot zone first increases and then decreases along the axial distance. The larger the temperature difference, the faster the diffusion speed of nitrogen in the fire safety work area, and the lower the oxygen concentration. When the temperature difference increases to 30 °C, the maximum oxygen concentration in the work area is 0.177; to control the problem of low oxygen content caused by the stack effect, three ventilation schemes are put forward. Through the analysis that installing fans symmetrically on both sides, 4 m away from the pipe opening, can effectively reduce the stack effect intensity when the optimal working wind speed of the fan is 4 m/s. The findings of this study can help in better understanding the causes of the chimney effect during pipeline fire safety work and provide theoretical basis for controlling personnel suffocation caused by the chimney effect.
- 30 September 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (40) , 25832-25840
Study on Gas Diffusion in Fire Working Areas of Oil and Gas Pipelines Based on Temperature Difference
When a pipeline is under fire safety work construction, the stack effect of the pipeline will increase the diffusion rate of nitrogen, reduce the oxygen content, and cause asphyxia. To prove the influence of the stack effect of the pipeline on the nitrogen movement in the pipeline and put forward effective ventilation control measures, the formation mechanism, gas diffusion law, and ventilation parameters of the stack effect of the oil and gas pipelines are studied through theoretical derivation and numerical simulation. The results show that the nitrogen concentration at the height of the breathing zone in the hot zone first increases and then decreases along the axial distance. The larger the temperature difference, the faster the diffusion speed of nitrogen in the fire safety work area, and the lower the oxygen concentration. When the temperature difference increases to 30 °C, the maximum oxygen concentration in the work area is 0.177; to control the problem of low oxygen content caused by the stack effect, three ventilation schemes are put forward. Through the analysis that installing fans symmetrically on both sides, 4 m away from the pipe opening, can effectively reduce the stack effect intensity when the optimal working wind speed of the fan is 4 m/s. The findings of this study can help in better understanding the causes of the chimney effect during pipeline fire safety work and provide theoretical basis for controlling personnel suffocation caused by the chimney effect.
- 26 August 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (35) , 21988-21998
Study on Parameters of a New Gas–Water Spray in Ore Pass Dedusting Based on Experiment and Numerical Simulation
To solve the problem of ore unloading dust in ore pass crosscuts, the atomization characteristics of a new gas–water spray and the effect of the ore discharge airflow on the spray effect were studied by experiments, and the installation position of the spray nozzle in the crosscut was determined by numerical simulation. The results show that when the gas–water flow ratio is 100–150, the atomization effect is the best. In this situation, the droplet size can be less than 28 μm. The impact airflow induced by ore unloading has a great influence on the size of the spray droplets, and the dust-collecting ability of the spray is negatively correlated with the impinging airflow. The best location for the spray is 5 m away from the wellhead. At this position, the impact airflow is less than 1.5 m/s, which can ensure that the total dustfall rate of the gas–water spray is 67% and that of the respiratory dust is 34%.
- 26 August 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (35) , 21988-21998
Study on Parameters of a New Gas–Water Spray in Ore Pass Dedusting Based on Experiment and Numerical Simulation
To solve the problem of ore unloading dust in ore pass crosscuts, the atomization characteristics of a new gas–water spray and the effect of the ore discharge airflow on the spray effect were studied by experiments, and the installation position of the spray nozzle in the crosscut was determined by numerical simulation. The results show that when the gas–water flow ratio is 100–150, the atomization effect is the best. In this situation, the droplet size can be less than 28 μm. The impact airflow induced by ore unloading has a great influence on the size of the spray droplets, and the dust-collecting ability of the spray is negatively correlated with the impinging airflow. The best location for the spray is 5 m away from the wellhead. At this position, the impact airflow is less than 1.5 m/s, which can ensure that the total dustfall rate of the gas–water spray is 67% and that of the respiratory dust is 34%.
- 2 July 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (27) , 16470-16481
Research on Control of Ore Pass Dust by Unloading Time Interval and Foam Control Technology
To control the dust pollution caused by the unloading of a multilevel ore pass, numerical simulation and similar experiments were carried out to study the airflow and dust migration influenced by the unloading quantity and the continuous unloading at different time intervals in the ore pass. From this research, the following conclusions are drawn: when the first level of the ore pass is unloaded, the third and fourth levels are the main dust-producing positions, and the concentrations of dust in the breathing zone can reach 85 and 325 mg/m3, respectively. Increasing the unloading interval and reducing the total single unloading quantity can prevent the superposition of dust production. The foam dust removal technology can reduce the secondary dust generation caused by the backlash of the airflow in the ore pass, and the dust emission rate can reach 60% at the fourth level.
- 2 July 2020
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 5 (27) , 16470-16481
Research on Control of Ore Pass Dust by Unloading Time Interval and Foam Control Technology
To control the dust pollution caused by the unloading of a multilevel ore pass, numerical simulation and similar experiments were carried out to study the airflow and dust migration influenced by the unloading quantity and the continuous unloading at different time intervals in the ore pass. From this research, the following conclusions are drawn: when the first level of the ore pass is unloaded, the third and fourth levels are the main dust-producing positions, and the concentrations of dust in the breathing zone can reach 85 and 325 mg/m3, respectively. Increasing the unloading interval and reducing the total single unloading quantity can prevent the superposition of dust production. The foam dust removal technology can reduce the secondary dust generation caused by the backlash of the airflow in the ore pass, and the dust emission rate can reach 60% at the fourth level.
- 7 May 2020
- Published by IOP Publishing in Chinese Physics B
- Vol. 29 (7) , 073401
Surface for methane combustion: O(3P) +CH4 → OH+CH3*
Kinetic investigations including quasi-classical trajectory and canonical unified statistical theory method calculations are carried out on a potential energy surface for the hydrogen-abstraction reaction from methane by atom O(3P). The surface is constructed using a modified Shepard interpolation method. The ab initio calculations are performed at the CCSD(T) level. Taking account of the contribution of inner core electrons to electronic correlation interaction in ab initio electronic structure calculations, modified optimized aug-cc-pCVQZ basis sets are applied to the all-electrons calculations. On this potential energy surface, the triplet oxygen atom attacks methane in a near-collinear H–CH3 direction to form a saddle point with barrier height of 13.55 kcal/mol, which plays a key role in the kinetics of the title reaction. For the temperature range of 298–2500 K, our calculated thermal rate constants for the O(3P) + CH4 → OH + CH3 reaction show good agreement with relevant experimental data. This work provides detailed mechanism of this gas-phase reaction and a theoretical guidance for methane combustion.
- 7 May 2020
- Published by IOP Publishing in Chinese Physics B
- Vol. 29 (7) , 073401
Surface for methane combustion: O(3P) +CH4 → OH+CH3*
Kinetic investigations including quasi-classical trajectory and canonical unified statistical theory method calculations are carried out on a potential energy surface for the hydrogen-abstraction reaction from methane by atom O(3P). The surface is constructed using a modified Shepard interpolation method. The ab initio calculations are performed at the CCSD(T) level. Taking account of the contribution of inner core electrons to electronic correlation interaction in ab initio electronic structure calculations, modified optimized aug-cc-pCVQZ basis sets are applied to the all-electrons calculations. On this potential energy surface, the triplet oxygen atom attacks methane in a near-collinear H–CH3 direction to form a saddle point with barrier height of 13.55 kcal/mol, which plays a key role in the kinetics of the title reaction. For the temperature range of 298–2500 K, our calculated thermal rate constants for the O(3P) + CH4 → OH + CH3 reaction show good agreement with relevant experimental data. This work provides detailed mechanism of this gas-phase reaction and a theoretical guidance for methane combustion.