Andrii Dvornyk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Andrii Dvornyk has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Gennadii Golub
National University of Life and Environmental Sciences of Ukraine
3 shared publications National University of Life and Environmental Sciences of Ukraine
2 shared publicationsAlexander Kuzyk
Central Ukrainian National Technical University
1 shared publication- Andrii Hrynkiv
Central Ukrainian National Technical University, Ukraine
1 shared publication - Andrii Tykhyi
Central Ukrainian National Technical University Universytetskyi ave., 8, Kropyvnytskyi, Ukraine, 25006
1 shared publication - Illia Volodymyrovych Tsaruk
Separated Subdivision of National University of Life and Environmental Sciences of Ukraine "Nizhyn Agrotechnical Institute
1 shared publication
Latest Publications
- Open Access
- 25 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (1 (131)) , 72-82
Determining the influence of structural and technological parameters of strip tillage on sunflower vegetation
The object of this study is the process of strip tillage, its effect on soil moisture in the strip, and subsequent vegetation of sunflower plants. At the same time, the task to increase the efficiency of strip tillage was solved. It has been established that the rational values of the structural and technological parameters of the strip tillage section in terms of fuel consumption depend on the speed of movement of the unit, the depth and width of the tilled strip of soil. One section of the unit was used for the research. The studies were conducted using the Box-Benkin three-factor experiment design. It was established that the rational values of the structural and technological parameters of strip tillage in terms of fuel consumption have the following values: the depth of strip tillage h=20‒25 cm, the width of strip tillage b=20‒25 cm, the speed of the unit from 7.5 to 11 km/hours. In this case, the actual fuel consumption ranged from 4.2 to 6.3 l/ha. It was also established that an increase in the width and depth of the strip cultivation leads to an increase in moisture loss in it. The highest value of soil moisture occurs at the minimum values of the depth and width of the strip cultivation, and the lowest at their maximum values. The influence of the width of the cultivated strip on the height of sunflower plants is more significant than the influence of the depth of tillage. This applies both to the range of changes in the height of sunflower plants (12.4‒13.6 cm compared to 12.5‒13.1 cm) and the intensity of the impact. The greatest influence on the height of sunflower plants is exerted by the magnitude of the transverse displacement of the axis of the row of plants. The intensity of this influence is approximately the same as the depth of tillage, and the range of changes in the height of sunflower plants is 11.7‒14 cm. Research results could be used in the design of units for strip tillage and sowing units.
- 25 October 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 5 (1 (131)) , 72-82
Open AccessDetermining the influence of structural and technological parameters of strip tillage on sunflower vegetation
The object of this study is the process of strip tillage, its effect on soil moisture in the strip, and subsequent vegetation of sunflower plants. At the same time, the task to increase the efficiency of strip tillage was solved. It has been established that the rational values of the structural and technological parameters of the strip tillage section in terms of fuel consumption depend on the speed of movement of the unit, the depth and width of the tilled strip of soil. One section of the unit was used for the research. The studies were conducted using the Box-Benkin three-factor experiment design. It was established that the rational values of the structural and technological parameters of strip tillage in terms of fuel consumption have the following values: the depth of strip tillage h=20‒25 cm, the width of strip tillage b=20‒25 cm, the speed of the unit from 7.5 to 11 km/hours. In this case, the actual fuel consumption ranged from 4.2 to 6.3 l/ha. It was also established that an increase in the width and depth of the strip cultivation leads to an increase in moisture loss in it. The highest value of soil moisture occurs at the minimum values of the depth and width of the strip cultivation, and the lowest at their maximum values. The influence of the width of the cultivated strip on the height of sunflower plants is more significant than the influence of the depth of tillage. This applies both to the range of changes in the height of sunflower plants (12.4‒13.6 cm compared to 12.5‒13.1 cm) and the intensity of the impact. The greatest influence on the height of sunflower plants is exerted by the magnitude of the transverse displacement of the axis of the row of plants. The intensity of this influence is approximately the same as the depth of tillage, and the range of changes in the height of sunflower plants is 11.7‒14 cm. Research results could be used in the design of units for strip tillage and sowing units.
- Open Access
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (12 (129)) , 6-18
Revealing patterns of change in the tribological efficiency of composite materials for machine parts based on phenylone and polyamide reinforced with arimide-t and fullerene
The object of the study is the process of changing tribological efficiency according to tribotechnical characteristics (wear intensity, friction coefficient, temperature in the contact zone) of composites based on phenylone C-1 and polyamide PA-6 with arimide-T filler and fullerene C-60. The study solved the problem of obtaining composites with high wear resistance. Based on the results of research, it was found that varying the content of arimide-T makes it possible to obtain composites with different patterns of changes in tribotechnical characteristics under conditions of dry friction, lubrication with water and I-50 oil. Composites with the composition: phenylone C-1+15 wt. have the maximum tribological efficiency. % arimide-T+3 wt. % fullerene C-60 and polyamide PA-6+30 wt. % arimide-T+3 wt. % fullerene C-60. Phenylone C-1 has destructive properties when working in the environment of water and temperature in the friction zone. Its reinforcement with arimide-T and fullerene C60 gave positive results of a complex of tribotechnical characteristics under these conditions. It was found that the wear of composites based on phenylone C-1 in I-50 oil is two orders of magnitude lower than in water. Research of samples from the obtained composites based on phenylone C-1 and polyamide PA-6, reinforced with the optimal content of arimide-T and fullerene C60, showed that their wear resistance when lubricated with oil is 3.5...4.0 times greater than the wear resistance of bronze. An applied aspect of the reported results is the introduction of manufacturing technologies and restoration of machine parts from the proposed composites. It has been proven that their optimal composition contributes to high tribological efficiency and could provide the required level of wear resistance and reliability of resource-determining nodes, systems, and machine assemblies. The results could be used by machine-building and repair-technological enterprises
- 28 June 2024
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 3 (12 (129)) , 6-18
Open AccessRevealing patterns of change in the tribological efficiency of composite materials for machine parts based on phenylone and polyamide reinforced with arimide-t and fullerene
The object of the study is the process of changing tribological efficiency according to tribotechnical characteristics (wear intensity, friction coefficient, temperature in the contact zone) of composites based on phenylone C-1 and polyamide PA-6 with arimide-T filler and fullerene C-60. The study solved the problem of obtaining composites with high wear resistance. Based on the results of research, it was found that varying the content of arimide-T makes it possible to obtain composites with different patterns of changes in tribotechnical characteristics under conditions of dry friction, lubrication with water and I-50 oil. Composites with the composition: phenylone C-1+15 wt. have the maximum tribological efficiency. % arimide-T+3 wt. % fullerene C-60 and polyamide PA-6+30 wt. % arimide-T+3 wt. % fullerene C-60. Phenylone C-1 has destructive properties when working in the environment of water and temperature in the friction zone. Its reinforcement with arimide-T and fullerene C60 gave positive results of a complex of tribotechnical characteristics under these conditions. It was found that the wear of composites based on phenylone C-1 in I-50 oil is two orders of magnitude lower than in water. Research of samples from the obtained composites based on phenylone C-1 and polyamide PA-6, reinforced with the optimal content of arimide-T and fullerene C60, showed that their wear resistance when lubricated with oil is 3.5...4.0 times greater than the wear resistance of bronze. An applied aspect of the reported results is the introduction of manufacturing technologies and restoration of machine parts from the proposed composites. It has been proven that their optimal composition contributes to high tribological efficiency and could provide the required level of wear resistance and reliability of resource-determining nodes, systems, and machine assemblies. The results could be used by machine-building and repair-technological enterprises
- 1 January 2022
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- Vol. 2 (31(45)) , 96-103
INFLUENCE LOCATION OF THE WORKING BODIES OF THE SECTION FOR STRIP TILLAGE ON TRACTION RESISTANCE AND FUEL CONSUMPTION
Justification of traction resistance with determination of fuel consumption when changing the mutual placement of the working bodies of the section for strip tillage. The practical result will be the use of the obtained data for the assembly for strip tillage with an energy device.
- 1 January 2022
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- Vol. 2 (31(45)) , 96-103
INFLUENCE LOCATION OF THE WORKING BODIES OF THE SECTION FOR STRIP TILLAGE ON TRACTION RESISTANCE AND FUEL CONSUMPTION
Justification of traction resistance with determination of fuel consumption when changing the mutual placement of the working bodies of the section for strip tillage. The practical result will be the use of the obtained data for the assembly for strip tillage with an energy device.
- 25 December 2020
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- No. 27(41)
INFLUENCE OF CONSTRUCTIVE AND TECHNOLOGICAL PARAMETERS OF THE UNIT FOR STRIP TILL ON THE LUMPINESS
The goal of the work. Investigate the influence of the relative position of the depth of processing with a chisel, the speed of movement of the unit and the distance between the cutting side discs on the lumpiness of the processed strip. Methods of research: analytical - quantitative determination of the quality of strip tillage; laboratory-field - for research, an experimental installation was completed with an MTZ-892 tractor and a section of the unit for strip tillage; statistical with generally accepted agronomic and economic methods. Results. Experimental studies of changes in the design and technological parameters of the unit for strip processing with the determination of lumpiness have been carried out. To study the main parameters, the depth of processing of the subsoiler (chisel) is taken from 13 to 27 cm, the distance between the cutting side discs is from 10 to 30 cm, the speed of the MTA is from 4 to 11 km/h. Unchanged parameters during the study: the distance from the axis of the front disc to the chisel is 50 cm, the distance from the chisel to the axis of the cutting side discs is 50 cm, the immersion depth of the cutting side discs is 10 cm. Experimental background is winter wheat stubble. Soil cultivation for winter wheat - deep (18 cm) disking, before that plowing to a depth of 25 cm. According to the research results, graphs of the dependence of lumpiness on the relative position of the chisel, cutting side discs and changes in the speed of the MTA were built. As the speed and distance between the side cutting discs increase, the lumpiness value decreases. Conclusions. Based on the results of the studies, the dependences of lumpiness on the relative position of the chisel and cutting side disks were obtained when the speed of the MTA was changed. It was determined that with an increase in the processing depth, the distance between the cutting side discs of 20 cm and the MTA movement speed of 7.5 km / h, a uniform increase in lumpiness is observed. The distance between the side cutting discs of 10 cm is not suitable for work.
- 25 December 2020
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- No. 27(41)
INFLUENCE OF CONSTRUCTIVE AND TECHNOLOGICAL PARAMETERS OF THE UNIT FOR STRIP TILL ON THE LUMPINESS
The goal of the work. Investigate the influence of the relative position of the depth of processing with a chisel, the speed of movement of the unit and the distance between the cutting side discs on the lumpiness of the processed strip. Methods of research: analytical - quantitative determination of the quality of strip tillage; laboratory-field - for research, an experimental installation was completed with an MTZ-892 tractor and a section of the unit for strip tillage; statistical with generally accepted agronomic and economic methods. Results. Experimental studies of changes in the design and technological parameters of the unit for strip processing with the determination of lumpiness have been carried out. To study the main parameters, the depth of processing of the subsoiler (chisel) is taken from 13 to 27 cm, the distance between the cutting side discs is from 10 to 30 cm, the speed of the MTA is from 4 to 11 km/h. Unchanged parameters during the study: the distance from the axis of the front disc to the chisel is 50 cm, the distance from the chisel to the axis of the cutting side discs is 50 cm, the immersion depth of the cutting side discs is 10 cm. Experimental background is winter wheat stubble. Soil cultivation for winter wheat - deep (18 cm) disking, before that plowing to a depth of 25 cm. According to the research results, graphs of the dependence of lumpiness on the relative position of the chisel, cutting side discs and changes in the speed of the MTA were built. As the speed and distance between the side cutting discs increase, the lumpiness value decreases. Conclusions. Based on the results of the studies, the dependences of lumpiness on the relative position of the chisel and cutting side disks were obtained when the speed of the MTA was changed. It was determined that with an increase in the processing depth, the distance between the cutting side discs of 20 cm and the MTA movement speed of 7.5 km / h, a uniform increase in lumpiness is observed. The distance between the side cutting discs of 10 cm is not suitable for work.
- 1 June 2019
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- No. 24(38)
THE INFLUENCE OF CONSTRUCTION-TECHNOLOGICAL PARAMETERS ON THE QUALITY OF STRIP TILL
????? ????????ֲ???-???????ò???? ???????в? ?? ?ʲ??? ????????? ????????? ??????
- 1 June 2019
- Published by Leonid Pogorilyy Ukrainian Scientific Research Institute in Technical and technological aspects of development and testing of new machinery and technologies for agriculture of Ukraine
- No. 24(38)
THE INFLUENCE OF CONSTRUCTION-TECHNOLOGICAL PARAMETERS ON THE QUALITY OF STRIP TILL
????? ????????ֲ???-???????ò???? ???????в? ?? ?ʲ??? ????????? ????????? ??????