ZCZheng Cheng

Zheng Cheng

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zheng Cheng has a total of 5 co-authors. Here are the top co-authors by number of shared publications:

  • Mao-Hua Du

    Department of Mechanical Engineering, Kunming University of Science and Technology, Kunming 650500, China

    2 shared publications
  • Shensong Wang

    Department of Mechanical Engineering, Kunming University of Science and Technology, Kunming 650500, China

    2 shared publications
  • Junhua Wang

    Department of Mechanical Engineering, Kunming University of Science and Technology, Kunming 650500, China

    1 shared publication
  • Peixin Wang

    of AE signal after wavelet decompositions in each frequency band.The histogram for Table 7 is shown in Figure 17. It can be seen from Figure 17 that the energy of the AE signal is mainly distributed in several frequency bands of D2, D3, D4, D5, and D6. The energy proportions in D2 and D3 bands decrease with the increase of tool wear, and the energy proportions in the D5 and D6 frequency bands increase with the tool wear

    1 shared publication
  • Yanfei Zhang

    Department of Mechanical Engineering

    1 shared publication

Latest Publications

  • Open Access

    Intelligent Turning Tool Monitoring with Neural Network Adaptive Learning

    by Maohua Du, Peixin Wang, Junhua Wang, Zheng Cheng, Shensong Wang

    Tool state monitoring is a key technology in intelligent manufacturing. But it is still in a research stage and lacks general adaptability for different machining conditions. To overcome this limitation, this work systematically investigates an intelligent, real‐time, and visible tool state monitoring through adopting integrated theories and technologies, i.e., (a) through distinctively designed experimental technique with comprehensive consideration of cutting parameters and tool wear values as variables, (b) through bisensor fusion for simultaneous measurements of low and high frequency signals, (c) through multitheory fusion of wavelet decomposition and the Relief‐F algorithm for performing dual feature extraction and feature dimension reduction to achieve more accurate state identification using neural network, and (d) through an innovative programming technique of MATLAB‐nested labVIEW. This tool monitoring system has neural network adaptive learning ability with the change of the experimental sample signals which are collected simultaneously by selected vibration and acoustic emission (AE) sensors in all factors turning experiments. Based on LabVIEW and MATLAB hybrid programming, the waveforms of signals are observed and the significant characteristics of signals are extracted through the time‐frequency domain analysis and then the calculation of the energy proportion of each frequency band obtained using 4 levels of wavelet packet decompositions of the vibration signal as well as 8 levels of wavelet multiresolution decompositions of the AE signal; the ensuing Relief‐F algorithm is used to further reextract the features that are most relevant to the tool state as input of neural network pattern recognition. Through the BP neural network adaptive learning, tool state recognition model is finally established. The results show that the correct recognition rate of BP network model after samples training is 92.59%, which can more accurately and intelligently monitor the tool wear state.


  • Open Access

    Multiobjective Optimization of Tool Geometric Parameters Using Genetic Algorithm

    by Maohua Du, Zheng Cheng, Yanfei Zhang, Shensong Wang

    Tool geometric parameters have a huge impact on tool wear. Up to now, there are only a few researches on tool geometric parameters and optimization, and the single objective function of parameter optimization used by researchers during high‐speed machining (HSM) mainly is the minimum cutting force. However, the elevated cutting temperature also greatly affects tool wear due to the numerous cutting heat generation. Thus, to reduce tool wear, it is the most fundamental approach to taking into account the comprehensive control of the cutting force and cutting temperature because they are the two most important physical quantities in metal cutting processes. This work proposes a new optimization idea of the cutting‐tool’s multi geometric parameters (three main parameters: rake angle, clearance angle, and cutting edge radius) with two objective functions (the cutting force and the temperature). Based on the response surface method (RSM), we have established the modified functional relation models of the influence of tool geometric parameters on the cutting force and temperature according to the finite element simulation results in high‐speed cutting of Ti6Al4V. Then the models are solved by using a genetic algorithm, and the optimal tool geometric parameters values that can concurrently control the two objectives in their minimum values are obtained. The advantages lie in the strategy of the separate models of the cutting force and cutting temperature owing to their different dimensions and the solution of the models through giving the cutting force and cutting temperature different weight coefficients. The optimal results are verified by experiments, which shows that the optimal tool geometric parameters are very effective and vital for ensuring both the cutting force and the cutting temperature not too high. This work is of great significance to the cutting tool design theory and its manufacturing for reducing tool wear.