Peiming Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Peiming Wang has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Xianping Liu
School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
5 shared publications - Bo Chen
Key Laboratory of Advanced Civil Engineering Materials (the Ministry of Education), School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
3 shared publications - Fei Yang
School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
3 shared publications - Yongming Zhang
School of Materials Science and Engineering, Tongji University, Shanghai 201804, China
3 shared publications - Ian K. Robinson
Brookhaven National Laboratory
2 shared publications - Linglin Xu
Key Laboratory of Advanced Civil Engineering Materials of Ministry of Education, School of Materials Science and Engineering, Tongji University, Shanghai, China
2 shared publications
Latest Publications
- Open Access
Influence of Mineral Additives on the Efflorescence of Ettringite-Rich Systems
Efflorescence is aesthetically undesirable to all cementitious materials products and mainly results from the carbonation of hydrates and salt precipitation. Alternative binders without portlandite formation theoretically have much lower efflorescence risk, but in practice, the efflorescence of ettringite-rich systems is still serious. This study reports the impacts of mineral additives on the efflorescence of ettringite-rich systems and the corresponding microstructural evolution. The effects of silica fume, limestone powder, and diatomite on efflorescence and the capillary pore structure of mortars were investigated from a multi-scale analysis. The composition and microstructure of efflorescent phases were revealed by optical microscope (O.M.), in-situ Raman spectroscopy, and Scanning Electron Microscopy (SEM). Results indicate that the addition of mineral additives can efficiently inhibit the efflorescence of reference, especially with silica fume. Similar to the ettringite-rich system, the efflorescence substances of all modifies are composed of ettringite and CaCO3, indicating that the addition of mineral admixture does not lead to chemical reactions, lower capillary absorption coefficient of mineral additives modified specimen, the denser pore structure and the lower efflorescence degree.
Open AccessInfluence of Mineral Additives on the Efflorescence of Ettringite-Rich Systems
Efflorescence is aesthetically undesirable to all cementitious materials products and mainly results from the carbonation of hydrates and salt precipitation. Alternative binders without portlandite formation theoretically have much lower efflorescence risk, but in practice, the efflorescence of ettringite-rich systems is still serious. This study reports the impacts of mineral additives on the efflorescence of ettringite-rich systems and the corresponding microstructural evolution. The effects of silica fume, limestone powder, and diatomite on efflorescence and the capillary pore structure of mortars were investigated from a multi-scale analysis. The composition and microstructure of efflorescent phases were revealed by optical microscope (O.M.), in-situ Raman spectroscopy, and Scanning Electron Microscopy (SEM). Results indicate that the addition of mineral additives can efficiently inhibit the efflorescence of reference, especially with silica fume. Similar to the ettringite-rich system, the efflorescence substances of all modifies are composed of ettringite and CaCO3, indicating that the addition of mineral admixture does not lead to chemical reactions, lower capillary absorption coefficient of mineral additives modified specimen, the denser pore structure and the lower efflorescence degree.
- Open Access
Properties of Calcium Sulfoaluminate Cement Mortar Modified by Hydroxyethyl Methyl Celluloses with Different Degrees of Substitution
This paper studies the influence of hydroxyethyl methyl cellulose (HEMC) on the properties of calcium sulfoaluminate (CSA) cement mortar. In order to explore the applicability of different HEMCs in CSA cement mortars, HEMCs with higher and lower molar substitution (MS)/degree of substitution (DS) and polyacrylamide (PAAm) modification were used. At the same time, two kinds of CSA cements with different contents of ye’elimite were selected. Properties of cement mortar in fresh and hardened states were investigated, including the fluidity, consistency and water-retention rate of fresh mortar and the compressive strength, flexural strength, tensile bond strength and dry shrinkage rate of hardened mortar. The porosity and pore size distribution were also analyzed by mercury intrusion porosimetry (MIP). Results show that HEMCs improve the fresh state properties and tensile bond strength of both types of CSA cement mortars. However, the compressive strength of CSA cement mortars is greatly decreased by the addition of HEMCs, and the flexural strength is decreased slightly. The MIP measurement shows that HEMCs increase the amount of micron-level pores and the porosity. The HEMCs with different MS/DS have different effects on the improvement of tensile bond strength in different CSA cement mortars. PAAm modification can improve the tensile bond strength of HEMC-modified CSA cement mortar.
Open AccessProperties of Calcium Sulfoaluminate Cement Mortar Modified by Hydroxyethyl Methyl Celluloses with Different Degrees of Substitution
This paper studies the influence of hydroxyethyl methyl cellulose (HEMC) on the properties of calcium sulfoaluminate (CSA) cement mortar. In order to explore the applicability of different HEMCs in CSA cement mortars, HEMCs with higher and lower molar substitution (MS)/degree of substitution (DS) and polyacrylamide (PAAm) modification were used. At the same time, two kinds of CSA cements with different contents of ye’elimite were selected. Properties of cement mortar in fresh and hardened states were investigated, including the fluidity, consistency and water-retention rate of fresh mortar and the compressive strength, flexural strength, tensile bond strength and dry shrinkage rate of hardened mortar. The porosity and pore size distribution were also analyzed by mercury intrusion porosimetry (MIP). Results show that HEMCs improve the fresh state properties and tensile bond strength of both types of CSA cement mortars. However, the compressive strength of CSA cement mortars is greatly decreased by the addition of HEMCs, and the flexural strength is decreased slightly. The MIP measurement shows that HEMCs increase the amount of micron-level pores and the porosity. The HEMCs with different MS/DS have different effects on the improvement of tensile bond strength in different CSA cement mortars. PAAm modification can improve the tensile bond strength of HEMC-modified CSA cement mortar.
- Open Access
Effect of Mineral Composition and w/c Ratios to the Growth of AFt during Cement Hydration by In-Situ Powder X-ray Diffraction Analysis
AFt is one of the major products at the early stage of cement hydration. It is an important product that influences the performance of the fresh and hardened cement pastes such as the setting time. However, there is a lack of detailed investigation on the growth of AFt in the cement pastes with a long-time scale. In this work, we reported a detailed analysis by using in-situ powder X-ray diffraction (XRD) on the growth of AFt in the cement pastes during hydration. Samples of the hydrated ordinary Portland cement (OPC) and another locally produced Portland cement with very high tricalcium silicate (C3S) content with different water–cement (w/c) ratios were investigated continually till they were hydrated for about 270 days by powder XRD. The work shows that during Portland cement hydration, the AFt reaches its maximum content with very high speed within about 24 h, which is influenced by the content of C3S in the raw cement samples and the w/c ratios of the cement pastes. Once the maximum content of AFt was reached, it decreases very fast within the following couple of days, and then decreases slowly and finally reaches a stable level at the late stage of hydration. The results also present that a lower w/c ratio is beneficial to the formation of AFt and the conversion of AFt to AFm as well. While higher w/c ratios are favorable for the AFt to remain stable in the hardened cement pastes.
Open AccessEffect of Mineral Composition and w/c Ratios to the Growth of AFt during Cement Hydration by In-Situ Powder X-ray Diffraction Analysis
AFt is one of the major products at the early stage of cement hydration. It is an important product that influences the performance of the fresh and hardened cement pastes such as the setting time. However, there is a lack of detailed investigation on the growth of AFt in the cement pastes with a long-time scale. In this work, we reported a detailed analysis by using in-situ powder X-ray diffraction (XRD) on the growth of AFt in the cement pastes during hydration. Samples of the hydrated ordinary Portland cement (OPC) and another locally produced Portland cement with very high tricalcium silicate (C3S) content with different water–cement (w/c) ratios were investigated continually till they were hydrated for about 270 days by powder XRD. The work shows that during Portland cement hydration, the AFt reaches its maximum content with very high speed within about 24 h, which is influenced by the content of C3S in the raw cement samples and the w/c ratios of the cement pastes. Once the maximum content of AFt was reached, it decreases very fast within the following couple of days, and then decreases slowly and finally reaches a stable level at the late stage of hydration. The results also present that a lower w/c ratio is beneficial to the formation of AFt and the conversion of AFt to AFm as well. While higher w/c ratios are favorable for the AFt to remain stable in the hardened cement pastes.
- Open Access
Water Retention Mechanism of HPMC in Cement Mortar
In this paper, the effect of HPMC (hydroxypropyl methyl cellulose ether) on the cement mortar water retention (WR) and composition was studied. The relationship between the plastic viscosity and water retention of cement mortar was revealed. The results showed that HPMC formed a colloidal film with a 3D network structure in water, which changed the ability of water to migrate. The HPMC colloid adsorbed on the surface of cement and sand particles and played a bridging role due to the influence of the spatial network structure of the thin film. Fine particles formed a grid-like distribution, and the hydration products formed a unique fibrous tree-like structure. A positive correlation was observed between the plastic viscosity and the water holding capacity of cement mortar. Finally, the mechanism responsible for the improved water retention of cement mortar by HPMC was analyzed using the changing water migration capacity, migration channels, and mortar cohesion.
Open AccessWater Retention Mechanism of HPMC in Cement Mortar
In this paper, the effect of HPMC (hydroxypropyl methyl cellulose ether) on the cement mortar water retention (WR) and composition was studied. The relationship between the plastic viscosity and water retention of cement mortar was revealed. The results showed that HPMC formed a colloidal film with a 3D network structure in water, which changed the ability of water to migrate. The HPMC colloid adsorbed on the surface of cement and sand particles and played a bridging role due to the influence of the spatial network structure of the thin film. Fine particles formed a grid-like distribution, and the hydration products formed a unique fibrous tree-like structure. A positive correlation was observed between the plastic viscosity and the water holding capacity of cement mortar. Finally, the mechanism responsible for the improved water retention of cement mortar by HPMC was analyzed using the changing water migration capacity, migration channels, and mortar cohesion.
- Open Access
Three-Dimensional Characterization of Hardened Paste of Hydrated Tricalcium Silicate by Serial Block-Face Scanning Electron Microscopy
With the application of a three-dimensional (3D) characterization technique, serial block-face scanning electron microscopy (SBFSEM), the 3D microstructure of a hydrated cement monomineral, tricalcium silicate (C3S), was measured with nanoscale resolution. The 3D morphologies of anhydrous particles, hydrated products, and capillary pores were visualized. Closed and open pores were discovered inside an anhydrous particle. The size and distribution of both the anhydrous C3S particles and their capillary pores were analyzed quantitatively and the porosity was determined to be 9%. The distribution of pores was found to be in a good agreement with the inner and outer product model of Hu et. al., with an inner shell distance of 860 nm. Considering the spatial resolution of the instrument and the volume of sample measured, most pores in this experiment could be characterized as capillary pores.
Open AccessThree-Dimensional Characterization of Hardened Paste of Hydrated Tricalcium Silicate by Serial Block-Face Scanning Electron Microscopy
With the application of a three-dimensional (3D) characterization technique, serial block-face scanning electron microscopy (SBFSEM), the 3D microstructure of a hydrated cement monomineral, tricalcium silicate (C3S), was measured with nanoscale resolution. The 3D morphologies of anhydrous particles, hydrated products, and capillary pores were visualized. Closed and open pores were discovered inside an anhydrous particle. The size and distribution of both the anhydrous C3S particles and their capillary pores were analyzed quantitatively and the porosity was determined to be 9%. The distribution of pores was found to be in a good agreement with the inner and outer product model of Hu et. al., with an inner shell distance of 860 nm. Considering the spatial resolution of the instrument and the volume of sample measured, most pores in this experiment could be characterized as capillary pores.
- Open Access
Investigation of Three-Dimensional Microstructure of Tricalcium Silicate (C3S) by Electron Microscopy
A serial block-face scanning electron microscopy (SBFSEM) system, composed of a scanning electron microscope (SEM) and an ultra-microtome installed within the SEM vacuum chamber, has been used to characterize the three-dimensional (3D) microstructure of tricalcium silicate (C3S) grains embedded in epoxy resin. A selection of C3S grains were segmented and rendered with 3D-image processing software, which allowed the C3S grains to be clearly visualized and enabled statistically quantitative analysis. The results show that about 5% of the C3S grains have volumes larger than 1 μm3 and the average volume of the grains is 25 μm3. Pores can also be clearly seen in the biggest C3S grain, the volume of which is 3.6 × 104 μm3, and the mean volume and total volume of all the pores within this grain are 4.8 μm3 and 3.0 × 103 μm3, respectively. The reported work provides a new approach for the characterization of the 3D spatial structure of raw C3S materials, and the resulting 3D structure of the raw C3S is important for further systematic research on the relationships between the spatial microstructure and the hydration kinetics of C3S and other cement minerals.
Open AccessInvestigation of Three-Dimensional Microstructure of Tricalcium Silicate (C3S) by Electron Microscopy
A serial block-face scanning electron microscopy (SBFSEM) system, composed of a scanning electron microscope (SEM) and an ultra-microtome installed within the SEM vacuum chamber, has been used to characterize the three-dimensional (3D) microstructure of tricalcium silicate (C3S) grains embedded in epoxy resin. A selection of C3S grains were segmented and rendered with 3D-image processing software, which allowed the C3S grains to be clearly visualized and enabled statistically quantitative analysis. The results show that about 5% of the C3S grains have volumes larger than 1 μm3 and the average volume of the grains is 25 μm3. Pores can also be clearly seen in the biggest C3S grain, the volume of which is 3.6 × 104 μm3, and the mean volume and total volume of all the pores within this grain are 4.8 μm3 and 3.0 × 103 μm3, respectively. The reported work provides a new approach for the characterization of the 3D spatial structure of raw C3S materials, and the resulting 3D structure of the raw C3S is important for further systematic research on the relationships between the spatial microstructure and the hydration kinetics of C3S and other cement minerals.
- 14 December 2017
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 32 (6) , 1352-1360
Effect of fly ash on drying shrinkage of thermal insulation mortar with glazed hollow beads
- 14 December 2017
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 32 (6) , 1352-1360
Effect of fly ash on drying shrinkage of thermal insulation mortar with glazed hollow beads
- Open Access
- 29 July 2016
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 67, 07034
Accuracy of Image Analysis in Quantitative Study of Cement Paste
- 29 July 2016
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 67, 07034
Open AccessAccuracy of Image Analysis in Quantitative Study of Cement Paste
- 5 August 2014
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 29 (4) , 751-756
Effect of calcium aluminate cement variety on the hydration of portland cement in blended system
- 5 August 2014
- Published by Springer Nature in Journal of Wuhan University of Technology-Mater. Sci. Ed.
- Vol. 29 (4) , 751-756
Effect of calcium aluminate cement variety on the hydration of portland cement in blended system