Bo Yang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Bo Yang has a total of 40 co-authors. Here are the top co-authors by number of shared publications:
- Tao Yu
College of Chemistry and Chemical Engineering, Xi’an Shiyou University, Xi’an 710065, China
7 shared publications - Jinling Li
State Key Laboratory of Petroleum Pollution Control, College of Chemistry and Chemical Engineering, Xi’an Shiyou University, Xi’an 710065, China
5 shared publications - Chengtun Qu
Shaanxi Key Laboratory of Environmental Pollution Control Technology and Reservoir Protection of Oilfield, School of Chemistry and Chemical Engineering, Xi’an Shiyou University, Xi’an, China
4 shared publications - Chengtun Qu
State Key Laboratory of Petroleum Pollution Control, College of Chemistry and Chemical Engineering, Xi’an Shiyou University, Xi’an 710065, China
3 shared publications - Feng Qi
Department of Mechanical and Aerospace Engineering, University of Missouri-Columbia, Columbia, MO 65211, USA
2 shared publications - Jinghui Chen
Key Laboratory of Waste Minimisation Technology and Reservoir Protection of Oil and Gas Fields in Shaanxi Province, Xi’an Shiyou University, Xi’an 710065, China
2 shared publications
Latest Publications
- 16 September 2026
- Published by Springer Nature in Journal of Soils and Sediments
- Vol. 26 (10) , 360
Heavy metals in park surface dust and soil: pollution characteristics, ecological risk, and human health risks across 40 Chinese cities
- 16 September 2026
- Published by Springer Nature in Journal of Soils and Sediments
- Vol. 26 (10) , 360
Heavy metals in park surface dust and soil: pollution characteristics, ecological risk, and human health risks across 40 Chinese cities
- Open Access
- 25 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (19) , 14186
Research on Characteristics of Economic Development and Environmental Pollution in Typical Energy Regions
The data on economic development quality and environmental pollution intensity from 2001 to 2021 was selected by taking Shanxi province, a typical energy region of the country, as the research object was analyzed in the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi province over the past two decades by using linear regression, numerical fitting, and Pearson correlation coefficient, and was explored on their mutual relationship. The results show that Shanxi province has made long-term progress in economic development since 2001, with GDP increasing nearly 10 times and maintaining an average annual growth of about 7%. The main pollutants in the last 20 show a trend of steady change, first ascending and then descending, with the turning point occurring in the 12th Five-Year Plan period (2011–2015), which shows that the environmental policies and investments made by China and Shanxi governments in the last 10 years of the new era have taken effect. The results of the numerical fitting curve suggest that the per capita GDP shows a classical inverted “U” curve relationship with wastewater and SO2 emissions, respectively. The turning point occurs at around 20,000 yuan per capita GDP, while the relationship between chemical oxygen demand and ammonia nitrogen emissions is monotonically decreasing. The relationship with solid waste generation is monotonically increasing without the turning point. The results of the correlation analysis further supported the conclusion of the fitted curve.
- 25 September 2023
- Published by MDPI AG in Sustainability
- Vol. 15 (19) , 14186
Open AccessResearch on Characteristics of Economic Development and Environmental Pollution in Typical Energy Regions
The data on economic development quality and environmental pollution intensity from 2001 to 2021 was selected by taking Shanxi province, a typical energy region of the country, as the research object was analyzed in the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi province over the past two decades by using linear regression, numerical fitting, and Pearson correlation coefficient, and was explored on their mutual relationship. The results show that Shanxi province has made long-term progress in economic development since 2001, with GDP increasing nearly 10 times and maintaining an average annual growth of about 7%. The main pollutants in the last 20 show a trend of steady change, first ascending and then descending, with the turning point occurring in the 12th Five-Year Plan period (2011–2015), which shows that the environmental policies and investments made by China and Shanxi governments in the last 10 years of the new era have taken effect. The results of the numerical fitting curve suggest that the per capita GDP shows a classical inverted “U” curve relationship with wastewater and SO2 emissions, respectively. The turning point occurs at around 20,000 yuan per capita GDP, while the relationship between chemical oxygen demand and ammonia nitrogen emissions is monotonically decreasing. The relationship with solid waste generation is monotonically increasing without the turning point. The results of the correlation analysis further supported the conclusion of the fitted curve.
- Open Access
- 25 June 2023
- Published by MDPI AG in Preprints.org
Research on the Evolution Characteristics of Economic Development Quality and Environmental Pollution Intensity in Typical Energy Regions in the Last 20 Years
Taking Shanxi Province, a typical energy region in China, as the research object, data on economic development quality and environmental pollution intensity from 2001 to 2021 were selected. Linear regression, numerical simulation, and Pearson correlation coefficient were used to analyze the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi Province in the past 20 years, and to explore the relationship between economic development and environmental pollution. The results indicate that since 2001, Shanxi Province has made long-term progress in economic development, with GDP increasing by nearly 10 times and an average annual growth rate of around 7%. In the past 20 years, the main pollutants have shown a trend of increasing first and then decreasing steadily, with a turning point occurring during the "12th Five Year Plan" period. This shows that the environmental policies and investments of the Chinese and Shanxi provincial governments in the past 10 years have been effective in the new era. The numerical simulation curve results show that the per capita GDP exhibits a classic inverted "U" curve relationship with wastewater and SO2 emissions, with a turning point occurring at around 20000 yuan per capita GDP; However, there is a monotonic decreasing trend with Chemical oxygen demand and ammonia nitrogen emissions, and a monotonic increasing trend with solid waste generation. There is no turning point yet. The correlation analysis results further support the fitting curve conclusion.
- 25 June 2023
- Published by MDPI AG in Preprints.org
Open AccessResearch on the Evolution Characteristics of Economic Development Quality and Environmental Pollution Intensity in Typical Energy Regions in the Last 20 Years
Taking Shanxi Province, a typical energy region in China, as the research object, data on economic development quality and environmental pollution intensity from 2001 to 2021 were selected. Linear regression, numerical simulation, and Pearson correlation coefficient were used to analyze the evolution characteristics of economic development quality and environmental pollution intensity in Shanxi Province in the past 20 years, and to explore the relationship between economic development and environmental pollution. The results indicate that since 2001, Shanxi Province has made long-term progress in economic development, with GDP increasing by nearly 10 times and an average annual growth rate of around 7%. In the past 20 years, the main pollutants have shown a trend of increasing first and then decreasing steadily, with a turning point occurring during the "12th Five Year Plan" period. This shows that the environmental policies and investments of the Chinese and Shanxi provincial governments in the past 10 years have been effective in the new era. The numerical simulation curve results show that the per capita GDP exhibits a classic inverted "U" curve relationship with wastewater and SO2 emissions, with a turning point occurring at around 20000 yuan per capita GDP; However, there is a monotonic decreasing trend with Chemical oxygen demand and ammonia nitrogen emissions, and a monotonic increasing trend with solid waste generation. There is no turning point yet. The correlation analysis results further support the fitting curve conclusion.
- Open Access
- 21 June 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (13) , 7574
Recent Progress in Sludge Co-Pyrolysis Technology
With the development of society and industry, the treatment and disposal of sludge have become a challenge for environmental protection. Co-pyrolysis is considered a sustainable technology to optimize the pyrolysis process and improve the quality and performance of pyrolysis products. Researchers have investigated the sludge co-pyrolysis process of sludge with other wastes, such as biomass, coal, and domestic waste, in laboratories. Co-pyrolysis technology has reduced pyrolysis energy consumption and improved the range and quality of pyrolysis product applications. In this paper, the various types of sludge and the factors influencing co-pyrolysis technology have been classified and summarized. Simultaneously, some reported studies have been conducted to investigate the co-pyrolysis characteristics of sludge with other wastes, such as biomass, coal, and domestic waste. In addition, the research on and development of sludge co-pyrolysis are expected to provide theoretical support for the development of sludge co-pyrolysis technology. However, the technological maturity of sludge pyrolysis and co-pyrolysis is far and needs further study to achieve industrial applications.
- 21 June 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (13) , 7574
Open AccessRecent Progress in Sludge Co-Pyrolysis Technology
With the development of society and industry, the treatment and disposal of sludge have become a challenge for environmental protection. Co-pyrolysis is considered a sustainable technology to optimize the pyrolysis process and improve the quality and performance of pyrolysis products. Researchers have investigated the sludge co-pyrolysis process of sludge with other wastes, such as biomass, coal, and domestic waste, in laboratories. Co-pyrolysis technology has reduced pyrolysis energy consumption and improved the range and quality of pyrolysis product applications. In this paper, the various types of sludge and the factors influencing co-pyrolysis technology have been classified and summarized. Simultaneously, some reported studies have been conducted to investigate the co-pyrolysis characteristics of sludge with other wastes, such as biomass, coal, and domestic waste. In addition, the research on and development of sludge co-pyrolysis are expected to provide theoretical support for the development of sludge co-pyrolysis technology. However, the technological maturity of sludge pyrolysis and co-pyrolysis is far and needs further study to achieve industrial applications.
- Open Access
- 7 May 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (9) , 4725
Removal of Methylene Blue by Metal Oxides Supported by Oily Sludge Pyrolysis Residues
As a typical pollutant, methylene blue poses a serious threat to the environment and human health. Oily sludge pyrolysis residue loaded with metal oxides could be used to prepare composite materials, which is not only an effective way to treat oily sludge, but also a possible method to treat methylene blue pollutants. In this paper, composite materials (AC-CuO, AC-ZnO, and AC-TiO2) were prepared by oily sludge pyrolysis residue-loaded CuO, ZnO, and TiO2 directly, and characterized by XRD, SEM, EDS, BET, FT-IR, and XPS, and it was shown that the metal oxides were successfully supported on the pyrolysis residue. Then, the composite materials were applied to the removal of methylene blue solution. The removal effect of composite materials on methylene blue with respect to the impregnation time, impregnation ratio and dosage, and the contact time and number of regenerations were investigated, and the removal parameters were optimized by response surface methodology. The removal process for methylene blue was described by applying Lagergren, McKay, Langmuir isotherm, Freundlish isotherm and intraparticle diffusion models. According to the response surface methodology and the main factors affecting the removal effect of methylene blue, the results indicate that the removal effect of 5 mg/L methylene blue could reach 95.28%, 94.95%, and 96.96%, respectively, and the corresponding removal capacities were 4.76, 4.75, and 4.85 mg/g. In addition, kinetic studies showed that the removal process of methylene blue was mainly constituted by chemical adsorption. The intraparticle diffusion showed that the removal of methylene blue may be controlled by both liquid film diffusion and intraparticle diffusion. The isotherms showed that the adsorption sites of composites for methylene blue were uniformly distributed and had the same affinity. Furthermore, regeneration experiments showed that the composite materials were stable and had relatively reusability.
- 7 May 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (9) , 4725
Open AccessRemoval of Methylene Blue by Metal Oxides Supported by Oily Sludge Pyrolysis Residues
As a typical pollutant, methylene blue poses a serious threat to the environment and human health. Oily sludge pyrolysis residue loaded with metal oxides could be used to prepare composite materials, which is not only an effective way to treat oily sludge, but also a possible method to treat methylene blue pollutants. In this paper, composite materials (AC-CuO, AC-ZnO, and AC-TiO2) were prepared by oily sludge pyrolysis residue-loaded CuO, ZnO, and TiO2 directly, and characterized by XRD, SEM, EDS, BET, FT-IR, and XPS, and it was shown that the metal oxides were successfully supported on the pyrolysis residue. Then, the composite materials were applied to the removal of methylene blue solution. The removal effect of composite materials on methylene blue with respect to the impregnation time, impregnation ratio and dosage, and the contact time and number of regenerations were investigated, and the removal parameters were optimized by response surface methodology. The removal process for methylene blue was described by applying Lagergren, McKay, Langmuir isotherm, Freundlish isotherm and intraparticle diffusion models. According to the response surface methodology and the main factors affecting the removal effect of methylene blue, the results indicate that the removal effect of 5 mg/L methylene blue could reach 95.28%, 94.95%, and 96.96%, respectively, and the corresponding removal capacities were 4.76, 4.75, and 4.85 mg/g. In addition, kinetic studies showed that the removal process of methylene blue was mainly constituted by chemical adsorption. The intraparticle diffusion showed that the removal of methylene blue may be controlled by both liquid film diffusion and intraparticle diffusion. The isotherms showed that the adsorption sites of composites for methylene blue were uniformly distributed and had the same affinity. Furthermore, regeneration experiments showed that the composite materials were stable and had relatively reusability.
- Open Access
- 1 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3609
Effects of Different Heat Treatment Methods on Organic Pollutants and Heavy Metal Content in Oil Sludge Waste and Ecotoxicological Evaluation
The discharge of large amounts of oily sludge heat treatment residues constitutes a severe threat to the environment. However, little is known about the toxicity of these heat-treated residues. Current research has mainly focused on the toxic effects of single heavy metals or single hydrocarbons on plants, whereas the phytotoxic effects of hydrocarbon–metal mixtures have remained largely unexplored. In this study, pot experiments were conducted to evaluate the effects of different proportions of heat treatment residues (pyrolysis, heat-washing, and high-temperature oxidation residues) from three kinds of oily sludge on the physiological and biochemical parameters of mung bean plants. Higher proportions of residues decreased the germination rates and enzyme activity of mung beans compared to uncontaminated soil. When pyrolysis residue, hot-washing residue, and high-temperature thermal oxidation residue are used in green planting soil, their content must be lower than 30%, 90%, and 70%, respectively. Additionally, our findings indicated that the accumulation level of pollutants in oily sludge heat treatment residues was not high. However, the three kinds of residues exhibited different degrees of plant toxicity. The pyrolysis residue still exhibited strong ecotoxicity, even at low concentrations. In contrast, the toxicity of the hot-washing residue was much lower than that of the pyrolysis residue and the high-temperature thermal oxidation residue. Our findings indicated that mung bean is highly tolerant of contaminated soil and is therefore well suited for phytoremediation applications.
- 1 April 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (7) , 3609
Open AccessEffects of Different Heat Treatment Methods on Organic Pollutants and Heavy Metal Content in Oil Sludge Waste and Ecotoxicological Evaluation
The discharge of large amounts of oily sludge heat treatment residues constitutes a severe threat to the environment. However, little is known about the toxicity of these heat-treated residues. Current research has mainly focused on the toxic effects of single heavy metals or single hydrocarbons on plants, whereas the phytotoxic effects of hydrocarbon–metal mixtures have remained largely unexplored. In this study, pot experiments were conducted to evaluate the effects of different proportions of heat treatment residues (pyrolysis, heat-washing, and high-temperature oxidation residues) from three kinds of oily sludge on the physiological and biochemical parameters of mung bean plants. Higher proportions of residues decreased the germination rates and enzyme activity of mung beans compared to uncontaminated soil. When pyrolysis residue, hot-washing residue, and high-temperature thermal oxidation residue are used in green planting soil, their content must be lower than 30%, 90%, and 70%, respectively. Additionally, our findings indicated that the accumulation level of pollutants in oily sludge heat treatment residues was not high. However, the three kinds of residues exhibited different degrees of plant toxicity. The pyrolysis residue still exhibited strong ecotoxicity, even at low concentrations. In contrast, the toxicity of the hot-washing residue was much lower than that of the pyrolysis residue and the high-temperature thermal oxidation residue. Our findings indicated that mung bean is highly tolerant of contaminated soil and is therefore well suited for phytoremediation applications.
- Open Access
- 24 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2354
Construction and Degradation Performance Study of Polycyclic Aromatic Hydrocarbons (PAHs) Degrading Bacterium Consortium
PAHs are widely distributed in the environment and pose a serious threat to ecological security and human health. The P&A (Pseudomonas aeruginosa and Alcaligenes faecalis) bacterium consortium obtained in this study comes from oily sludge and is reused for the degradation of PAHs mixture in oily sludge. Few articles pay attention to the PAHs mixture in oily sludge and reuse the bacterium consortium for its degradation. The PAHs solution degradation efficient of P&A bacterial consortium under different environmental conditions, bioaugmentations, and exogenous stimulations were studied by ultraviolet visible spectrophotometer and gas chromatography–mass spectrometry. The result shows that, after 8 days of degradation under 35 °C, pH 7, with 5% (volume percent) of the inoculation amount, the degradation rate of NAP, PHE, and PYR solution could higher than 90%, 80%, and 70%, respectively. The additional crude oil could further improve the NAP, PHE, and PYR degradation efficiency. The minimum inhibitory concentration of Cu2+, Zn2+, and Pb2+ to bacterium were 2.002, 17.388, and 9.435 mM, respectively. The addition of surfactants had negative or limited positive effect on the PAHs degradation rate. Furthermore, the average degradation rates of NAP, PHE, and PYR, in oily sludge of local petroleum polluted area by P&A bacterial consortium, could all reach above 80%. Based on gas chromatography–mass spectrometry test results before and after incubation, P&A bacterial consortium also provides more opportunities for other organic compounds’ degradation.
- 24 February 2022
- Published by MDPI AG in Applied Sciences
- Vol. 12 (5) , 2354
Open AccessConstruction and Degradation Performance Study of Polycyclic Aromatic Hydrocarbons (PAHs) Degrading Bacterium Consortium
PAHs are widely distributed in the environment and pose a serious threat to ecological security and human health. The P&A (Pseudomonas aeruginosa and Alcaligenes faecalis) bacterium consortium obtained in this study comes from oily sludge and is reused for the degradation of PAHs mixture in oily sludge. Few articles pay attention to the PAHs mixture in oily sludge and reuse the bacterium consortium for its degradation. The PAHs solution degradation efficient of P&A bacterial consortium under different environmental conditions, bioaugmentations, and exogenous stimulations were studied by ultraviolet visible spectrophotometer and gas chromatography–mass spectrometry. The result shows that, after 8 days of degradation under 35 °C, pH 7, with 5% (volume percent) of the inoculation amount, the degradation rate of NAP, PHE, and PYR solution could higher than 90%, 80%, and 70%, respectively. The additional crude oil could further improve the NAP, PHE, and PYR degradation efficiency. The minimum inhibitory concentration of Cu2+, Zn2+, and Pb2+ to bacterium were 2.002, 17.388, and 9.435 mM, respectively. The addition of surfactants had negative or limited positive effect on the PAHs degradation rate. Furthermore, the average degradation rates of NAP, PHE, and PYR, in oily sludge of local petroleum polluted area by P&A bacterial consortium, could all reach above 80%. Based on gas chromatography–mass spectrometry test results before and after incubation, P&A bacterial consortium also provides more opportunities for other organic compounds’ degradation.
- Open Access
Corrosion Mechanism of L360 Pipeline Steel Coated with S8 in CO2-Cl− System at Different pH Values
The corrosion behavior of L360 pipeline steel coated with or without elemental sulfur (S8) in CO2–Cl− medium at different pH was studied. An autoclave was used to simulate the working conditions for forming the corrosion scale, and an electrochemical workstation with a three-electrode cell was used to analyze the electrochemical characterization of the corrosion scale. A wire beam electrode was used to determine the potential and current distribution, and scanning electron microscopy and X-ray diffraction were used to characterize the morphology and composition of the corrosion scale. The results showed that the deposition of S8 on the surface of the electrodes caused serious localized corrosion, especially under acidic conditions. The morphology and localized corrosion intensity index further proved that the deposition of S8 significantly promoted corrosion, especially pitting corrosion. Finally, a novel corrosion mechanism of L360 pipeline steel coated with S8 in a CO2-Cl− environment under acidic conditions was proposed, and we then modeled the theoretical mechanisms that explained the experimental results.
Open AccessCorrosion Mechanism of L360 Pipeline Steel Coated with S8 in CO2-Cl− System at Different pH Values
The corrosion behavior of L360 pipeline steel coated with or without elemental sulfur (S8) in CO2–Cl− medium at different pH was studied. An autoclave was used to simulate the working conditions for forming the corrosion scale, and an electrochemical workstation with a three-electrode cell was used to analyze the electrochemical characterization of the corrosion scale. A wire beam electrode was used to determine the potential and current distribution, and scanning electron microscopy and X-ray diffraction were used to characterize the morphology and composition of the corrosion scale. The results showed that the deposition of S8 on the surface of the electrodes caused serious localized corrosion, especially under acidic conditions. The morphology and localized corrosion intensity index further proved that the deposition of S8 significantly promoted corrosion, especially pitting corrosion. Finally, a novel corrosion mechanism of L360 pipeline steel coated with S8 in a CO2-Cl− environment under acidic conditions was proposed, and we then modeled the theoretical mechanisms that explained the experimental results.
- Open Access
Co-Deposition Mechanisms of Calcium Sulfate and Calcium Carbonate Scale in Produced Water
Co-precipitation of mineral-based salts during scaling remains poorly understood and thermodynamically undefined within the water industry. This study focuses on investigating calcium carbonate and calcium sulfate mixed precipitation in scaling. Scaling is often observed in the produced water supply as a result of treatment processes. Co-precipitation results were compared with experimental results of a single salt crystallization. Several parameters were carefully monitored, including the electrical conductivity, pH value, crystal morphology and crystal form. The existence of the calcium carbonate scale in the mixed system encourages the loose calcium sulfate scale to become more tightly packed. The mixed scale was firmly adhered to the beaker, and the adhesion of the co-deposition product was located between the pure calcium sulfate scale and the pure calcium carbonate scale. The crystalline form of calcium sulfate was gypsum in both pure material deposition and mixed deposition, while the calcium carbonate scale was stable in calcite form in the pure material deposition. In the co-deposition, apart from calcite form, some calcium carbonate scale crystals had metastable vaterite form. This indicated that the presence of SO42− ions reduced the energy barrier of the calcium carbonate scale and hindered its transformation from a vaterite form to a calcite one, and the increase in HCO3− content inhibited the formation of calcium sulfate scale.
Open AccessCo-Deposition Mechanisms of Calcium Sulfate and Calcium Carbonate Scale in Produced Water
Co-precipitation of mineral-based salts during scaling remains poorly understood and thermodynamically undefined within the water industry. This study focuses on investigating calcium carbonate and calcium sulfate mixed precipitation in scaling. Scaling is often observed in the produced water supply as a result of treatment processes. Co-precipitation results were compared with experimental results of a single salt crystallization. Several parameters were carefully monitored, including the electrical conductivity, pH value, crystal morphology and crystal form. The existence of the calcium carbonate scale in the mixed system encourages the loose calcium sulfate scale to become more tightly packed. The mixed scale was firmly adhered to the beaker, and the adhesion of the co-deposition product was located between the pure calcium sulfate scale and the pure calcium carbonate scale. The crystalline form of calcium sulfate was gypsum in both pure material deposition and mixed deposition, while the calcium carbonate scale was stable in calcite form in the pure material deposition. In the co-deposition, apart from calcite form, some calcium carbonate scale crystals had metastable vaterite form. This indicated that the presence of SO42− ions reduced the energy barrier of the calcium carbonate scale and hindered its transformation from a vaterite form to a calcite one, and the increase in HCO3− content inhibited the formation of calcium sulfate scale.