ZZZhiming Zhang

Zhiming Zhang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Zhiming Zhang has a total of 15 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Preparation and Performance Characterization of Exploding Foil Initiator Based on ODPA-ODA Polyimide Flyer

    by Zhiqing Wu, Fan Lei, Zhiqiang Zhan, Jiangshan Luo, Gao Niu, Zhaoguo Li, Tao Yi, Shufan Chen, Bo Yang, Qiubo Fu, et al.

    The exploding foil initiator (EFI) system has been extensively used in ignition and detonation sequences and proved to be of high safety and reliability. Polyimide is considered the ideal flyer material for EFI due to its excellent performance, including thermal stability, outstanding mechanical properties, high radiation resistance, and excellent dielectric properties. In this study, we prepared the EFI based on a polyimide (ODPA-ODA) flyer, which is spin-coated and solidified on patterned copper film in situ. The electric explosion test shows that the prepared EFI has good working performance, and the 4000 V working voltage drove the flyer to reach a maximum velocity of 5096 m/s. The polyimide morphology and chemical structure after the electric explosion was observed by microscope, SEM, XPS, and FTIR, which showed that the polyimide flyer underwent thermal deformation and complex chemical reactions during an electric explosion. A large number of polyimide bonds broke to form new carbonyl compounds, and the opening of aromatic rings was accompanied by the formation of aliphatic hydrocarbon chains. The morphology and chemical structure analysis after the electric explosion test will lay a foundation for us to further understand the working principle and evolution process of polyimide (ODPA-ODA) flyer.


  • Open Access

    The Hybrid Fabrication Process of Metal/Silicon Composite Structure for MEMS S&A Device

    by Tengjiang Hu, Kuang Fang, Zhiming Zhang, Xiaohua Jiang, Yulong Zhao

    The micro-electromechanical system (MEMS) safety-and-arming (S&A) device has the features of integration and miniaturization, which is one of the important directions of weapon development. Confined by the fabrication process, the silicon-based devices are too fragile, and the metal-based devices are low precision. In order to solve the contradiction between high precision and high structure strength, a metal/silicon composite structure is proposed in this paper, and a hybrid fabrication process is introduced. This new method mainly consists of metal sputtering, electroplating, and (inductively–coupled-plasma) ICP etching. As the resolution of the thick dry film is limited, the process of a femtosecond laser is applied to refine the structure, and the Ni plate (a block of 1 mm × 3 mm × 0.3 mm with a cavity of ϕ 0.85 mm × 0.3 mm in the center) is fabricated on the silicon-on-insulator (SOI) wafer successfully. After the double sides are etched by ICP, the SOI wafer is immersed in a buffered-oxide-etch (BOE) etchant to remove the buried layer. The cover plate acts as the encapsulation and is bonded with the SOI wafer by the epoxy glue. Then, the temporary support beam of the device is broken by the probe, and the suspended composite structure can be fully released. The hybrid process is the integration of the silicon-based process and the metal-based process, which can combine the advantages of both high precision and a high structure strength. The process proposed here is suitable for the application of weapon miniaturization.


  • Open Access

    Research on an On-Chip MEMS Based Safety and Arming Device with a Mechanical Encryption System

    by Kuang Fang, Tengjiang Hu, Xueting Zhang, Zhiming Zhang, Xiaohua Jiang, Yulong Zhao

    The design and characterization of microelectromechanical systems (MEMS) based on-chip SAD (Safety and Arming Device) are proposed. An encryption system has been integrated into the device to enhance its reliability during the electromagnetic interference. The conversion between safe status and arm status is reversible due to the bidirectional actuation design of the slider and pawl on the SOI (Silicon on Insulator) chip, being driven by the chevron electrothermal actuators. The width of each tooth on the slider, which contains coding information, is different from that of its adjacent neighbor. Additionally, the different teeth width, respectively 32 μm, 82 μm, requiring different decoding displacement of 100 μm and 150 μm, corresponds to the different decoding voltage of 13.5 V and 14.8 V. The travel range of interrupter in the SAD will only be limited by the chip dimension and be able to cover the motion of ±1 mm in the present research, due to the capability of motion retention. Finally, the SAD is integrated with a copper azide exploding chip to measure the average velocity of the titanium flyer for the application feasibility validation.