Xiaobin Lu
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Xiaobin Lu has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Meng Li
State Key Laboratory of Water Cycle and Water Security, China Institute of Water Resources and Hydropower Research, Beijing 100038, China
2 shared publications - Xiulin Li
State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, Beijing 100038, China
2 shared publications E. Z. Li
Heilongjiang Shuitou Linhai Reservoir Water Supply Engineering Management Co., Ltd., Mudanjiang, China
1 shared publication- Jutao Hao
Division of Materials, China Institute of Water Resources and Hydropower Research (IWHR), Beijing 100038, China
1 shared publication W. Jin
Heilongjiang Province Water Resources and Hydropower Group Co., Ltd., Harbin, China
1 shared publicationX. L. Li
State Key Laboratory of Simulation and Regulation of Water Cycle in River Basin, Beijing, China
1 shared publication
Latest Publications
- 1 May 2025
- Published by Springer Nature in Strength of Materials
- Vol. 57 (3) , 678-690
Experimental Study on Application of Polyurea Coating for Concrete Dams in Cold Regions
- 1 May 2025
- Published by Springer Nature in Strength of Materials
- Vol. 57 (3) , 678-690
Experimental Study on Application of Polyurea Coating for Concrete Dams in Cold Regions
- Open Access
- 14 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2030
Field Monitoring and Numerical Analysis of the Effect of Air Temperature and Water Load on the Static Behavior of a Tied-Arch Aqueduct
This study presents part of a pilot work for the structural health monitoring of a large tied-arch reinforced concrete aqueduct in eastern China. Based on field-monitored data for over a year, it mainly focuses on the effect of air temperature and water load variations on the static behavior of a typical span of the aqueduct through field monitoring and 3D FE model analysis. It is found that the longitudinal deformation of the composite tied-arch shows a good linear relationship with the air temperature during the non-operation period and also has a good bilinear correlation with the air temperature and water level during operation. However, isolation of the air temperature effect from the second bilinear correlation using the first linear relationship results in a poor correlation between the longitudinal deformation and water level due to the dominance of the temperature effect. Therefore, it is recommended to use the bilinear regression to predict the longitudinal deformation of the tied-arch during operation. The vertical deformation of the tied-arch is insignificantly affected by air temperature, whereas it shows a fair bilinear correlation with the air temperature and water level during operation, which can be used to provide a reasonable estimation of the vertical deformation of the tied-arch. The strain measurements of the tied-arch using vibrating-string gauges are more complicated due to the notable influence of the ambient temperature and solar radiation, but the relatively consistent bilinear regression of the strains versus the air temperature and water level can still give fair predictions for the strains of the bottom tension rods during operation. The 3D FE model can provide a fair estimation for the vertical deformation of the tied-arch under water load, but its predictions for longitudinal deformation and strains are less satisfactory when compared to monitored data excluding temperature effects.
- 14 February 2025
- Published by MDPI AG in Applied Sciences
- Vol. 15 (4) , 2030
Open AccessField Monitoring and Numerical Analysis of the Effect of Air Temperature and Water Load on the Static Behavior of a Tied-Arch Aqueduct
This study presents part of a pilot work for the structural health monitoring of a large tied-arch reinforced concrete aqueduct in eastern China. Based on field-monitored data for over a year, it mainly focuses on the effect of air temperature and water load variations on the static behavior of a typical span of the aqueduct through field monitoring and 3D FE model analysis. It is found that the longitudinal deformation of the composite tied-arch shows a good linear relationship with the air temperature during the non-operation period and also has a good bilinear correlation with the air temperature and water level during operation. However, isolation of the air temperature effect from the second bilinear correlation using the first linear relationship results in a poor correlation between the longitudinal deformation and water level due to the dominance of the temperature effect. Therefore, it is recommended to use the bilinear regression to predict the longitudinal deformation of the tied-arch during operation. The vertical deformation of the tied-arch is insignificantly affected by air temperature, whereas it shows a fair bilinear correlation with the air temperature and water level during operation, which can be used to provide a reasonable estimation of the vertical deformation of the tied-arch. The strain measurements of the tied-arch using vibrating-string gauges are more complicated due to the notable influence of the ambient temperature and solar radiation, but the relatively consistent bilinear regression of the strains versus the air temperature and water level can still give fair predictions for the strains of the bottom tension rods during operation. The 3D FE model can provide a fair estimation for the vertical deformation of the tied-arch under water load, but its predictions for longitudinal deformation and strains are less satisfactory when compared to monitored data excluding temperature effects.
- Open Access
- 29 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (12) , 2428
Numerical Study on Evaluating the Concrete-Bedrock Interface Condition for Hydraulic Tunnel Linings Using the SASW Method
The current methods for evaluating the contact condition between concrete and lining were the ground penetrating radar (GPR) and the coring method. The penetration of radar electromagnetic waves was greatly affected by steel reinforcement and water, which often made the detection results of GPR unsatisfactory. A spectral analysis of the surface wave (SASW) method was used to evaluate the concrete-bedrock interface condition for hydraulic tunnel linings in this paper, since the impact elastic wave is less affected by steel bars and water content. An SASW implementation program based on fast Fourier transformation (FFT) was developed to analyze data from numerical simulations and field tests. Various models were studied to investigate the feasibility of using numerical analysis. For the first time, the study was employed to find out the influences of different receiver spacings and impact duration on the efficiency of detecting the existence of a weak layer underneath the concrete using the SASW method. On this basis, in-situ tests were carried out to verify the applicability in the field and results were verified by coring. In the research, the following results were found: (1) The finite element analysis results of different uniform or layered models showed that the SASW method could accurately identify the interface contact condition between the concrete lining and bedrock, especially the existence of voids; (2) when the receiver spacing was 1.0–1.5 times the thickness of the target object to be inspected, the quality of the collected signal data was the best; (3) under a certain reasonable range, the impact duration had an insignificant effect on the phase spectra and dispersion curves of a concrete-weak layer model; (4) in-situ SASW inspection could accurately tell whether the voids exist at the concrete-bedrock interface; and (5) the data processing program of the SASW method based on the MATLAB platform was accurate, convenient, and worth promoting.
- 29 November 2018
- Published by MDPI AG in Applied Sciences
- Vol. 8 (12) , 2428
Open AccessNumerical Study on Evaluating the Concrete-Bedrock Interface Condition for Hydraulic Tunnel Linings Using the SASW Method
The current methods for evaluating the contact condition between concrete and lining were the ground penetrating radar (GPR) and the coring method. The penetration of radar electromagnetic waves was greatly affected by steel reinforcement and water, which often made the detection results of GPR unsatisfactory. A spectral analysis of the surface wave (SASW) method was used to evaluate the concrete-bedrock interface condition for hydraulic tunnel linings in this paper, since the impact elastic wave is less affected by steel bars and water content. An SASW implementation program based on fast Fourier transformation (FFT) was developed to analyze data from numerical simulations and field tests. Various models were studied to investigate the feasibility of using numerical analysis. For the first time, the study was employed to find out the influences of different receiver spacings and impact duration on the efficiency of detecting the existence of a weak layer underneath the concrete using the SASW method. On this basis, in-situ tests were carried out to verify the applicability in the field and results were verified by coring. In the research, the following results were found: (1) The finite element analysis results of different uniform or layered models showed that the SASW method could accurately identify the interface contact condition between the concrete lining and bedrock, especially the existence of voids; (2) when the receiver spacing was 1.0–1.5 times the thickness of the target object to be inspected, the quality of the collected signal data was the best; (3) under a certain reasonable range, the impact duration had an insignificant effect on the phase spectra and dispersion curves of a concrete-weak layer model; (4) in-situ SASW inspection could accurately tell whether the voids exist at the concrete-bedrock interface; and (5) the data processing program of the SASW method based on the MATLAB platform was accurate, convenient, and worth promoting.