MKMargarita Kostyanaya

Margarita Kostyanaya

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Margarita Kostyanaya has a total of 17 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Perstraction of Heat-Stable Salts from Aqueous Alkanolamine Solutions

    by M. I. Kostyanaya, A. A. Yushkin, D. S. Bakhtin, S. A. Legkov, S. D. Bazhenov

    Amine absorption processes designed to remove acid gases from gas streams generally face a major challenge of solvent degradation. This degradation leads to the formation of heat-stable salts (HSS), corrosive agents that irreversibly bind free alkanolamine. The present study proposes, for the first time, a method for HSS perstraction using a liquid–liquid membrane contactor that allows HSS to transfer through porous membranes from the solvent into a hydrophobic extractant represented by a methyltrioctylammonium solution in 1-octanol. The perstraction provides selective extraction of HSS anions without direct mixing of liquid phases or the formation of stable emulsions of the solvent and the extractant. For this purpose, a number of industrial and laboratory porous membrane samples fabricated from polyvinylidene fluoride, polypropylene, and polysulfone were investigated. Their chemical and morphological stability, surface properties, and transport properties were tested under prolonged (>600 h) contact with a model solvent (an aqueous monoethanolamine solution) and with the components of the selective extractant. The feasibility of HSS perstraction was demonstrated using the formic acid (as an HSS model) extraction from the model solvent. The most promising results were obtained for a system with a polyvinylidene fluoride membrane: up to 50% of formic acid was extracted over 18 h.


  • Open Access

    Interphase Surface Stability in Liquid-Liquid Membrane Contactors Based on Track-Etched Membranes

    by Stepan Bazhenov, Olga Kristavchuk, Margarita Kostyanaya, Anton Belogorlov, Ruslan Ashimov, Pavel Apel

    A promising solution for the implementation of extraction processes is liquid–liquid membrane contactors. The transfer of the target component from one immiscible liquid to another is carried out inside membrane pores. For the first time, highly asymmetric track-etched membranes made of polyethylene terephthalate (PET) of the same thickness but with different pore diameters (12.5–19 nm on one side and hundreds of nanometers on the other side) were studied in the liquid–liquid membrane contactor. For analysis of the liquid–liquid interface stability, two systems widely diverging in the interfacial tension value were used: water–pentanol and water–hexadecane. The interface stability was investigated depending on the following process parameters: the porous structure, the location of the asymmetric membrane in the contactor, the velocities of liquids, and the pressure drop between them. It was shown that the stability of the interface increases with decreasing pore size. Furthermore, it is preferable to supply the aqueous phase from the side of the asymmetric membrane with the larger pore size. The asymmetry of the porous structure of the membrane makes it possible to increase the range of pressure drop values between the phases by at least two times (from 5 to 10 kPa), which does not lead to mutual dispersion of the liquids. The liquid–liquid contactor based on the asymmetric track-etched membranes allows for the extraction of impurities from the organic phase into the aqueous phase by using a 1% solution of acetone in hexadecane as an example.


  • Membrane Absorption of Ethylene from a Mixture with Ethane Using MDK-3 Composite Membranes

    by M. I. Kostyanaya, S. D. Bazhenov, V. P. Vasilevsky, S. A. Legkov, A. V. Nikitin, I. V. Sedov, A. V. Volkov

    Separation of olefin/paraffin mixtures is an important problem. The use of a gas—liquid membrane contactor is an attractive alternative to traditional power-consuming cryogenic distillation methods. The paper deals with the separation of ethylene from its mixture with ethane (component ratio 19/81 vol %, respectively) using an aqueous silver nitrate solution as a selective ethylene absorbent in a flat-sheet lab-scale membrane module equipped with an MDK-3 commercial composite membrane with the selective layer based on silicone rubber. The effect of the absorbent and gas mixture feed linear velocities on the residual ethylene content of the mixture is considered. The thin selective layer of the membrane is shown to preserve high performance during long-term experimental run ensuring high mass-exchange characteristics and preventing the absorbent penetration into the porous structure of the membrane support.


  • Open Access

    Surface Modified Polysulfone Hollow Fiber Membranes for Ethane/Ethylene Separation Using Gas-Liquid Membrane Contactors with Ionic Liquid-Based Absorbent

    by Margarita Kostyanaya, Stepan Bazhenov, Ilya Borisov, Tatiana Plisko, Vladimir Vasilevsky

    Olefin/paraffin separation is an important technological process. A promising alternative to conventional energy-consuming methods is employment of gas-liquid membrane contactors. In the present work, the membranes used were polysulfone (PSf) asymmetrical porous hollow fibers fabricated via the NIPS (non-solvent induced phase separation) technique in the free spinning mode. The surface of the fine-pored selective layer from the lumen side of the fibers was modified by layer-by-layer deposition of perfluorinated acrylic copolymer Protect Guard® in order to hydrophobized the surface and to avoid penetration of the liquid absorbent in the porous structure of the membranes. The absorbents studied were silver salts (AgNO3 and AgBF4) solutions in five ionic liquids (ILs) based on imidazolium and phosphonium cations. The membranes were analyzed through gas permeance measurement, SEM and dispersive X-ray (EDXS). Contact angle values of both unmodified and modified membranes were determined for water, ethylene glycol, ILs and silver salts solutions in ILs. It was shown that the preferable properties for employment in membrane contactor refer to the PSf hollow fiber membranes modified by two layers of Protect Guard®, and to the absorbent based on 1 M AgNO3 solution in 1-ethyl-3-methylimidazolium dicyanamide. Using the membrane contactor designed, ethylene/ethane mixture (80/20) separation was carried out. The fluxes of both components as well as their overall mass transport coefficients (MTC) were calculated. It was shown that the membrane absorption system developed provides absorption of approx. 37% of the initial ethylene volume in the mixture. The overall MTC value for ethylene was 4.7 GPU (gas permeance unit).