Eric Baer
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Eric Baer has a total of 48 co-authors. Here are the top co-authors by number of shared publications:
Anne Hiltner
Department of Macromolecular Science and Engineering, Center for Layered Polymeric Systems, Case Western Reserve University, Cleveland, Ohio 44106-7202
7 shared publications- Lei Zhu
Department of Macromolecular Science and Engineering Case Western Reserve University Cleveland Ohio USA
7 shared publications - Lionel Flandin
Univ. Grenoble Alpes, Univ. Savoie Mont Blanc, CNRS, Grenoble INP, LEPMI Grenoble France
4 shared publications Matthew Mackey
Center for Layered Polymeric Systems (CLiPS) and Department of Macromolecular Science and Engineering, Case Western Reserve University, Cleveland, Ohio, USA
4 shared publications- Andrew Olah
Center for Layered Polymeric Systems (CLiPS), Department of Macromolecular Science and Engineering Case Western Reserve University Cleveland Ohio USA
3 shared publications Deepak S. Langhe
Department of Macromolecular Science and Engineering, Center for Layered Polymeric Systems, Case Western Reserve University, Cleveland, Ohio 44106-7202
3 shared publications
Latest Publications
- 27 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (1) , 795-806
Effect of Glass Transition Temperature on Enhanced Dielectric Breakdown Strength and Lifetime of Multilayer Polymer Films
High temperature, high energy density, and low loss dielectric films are promising candidates for miniaturized capacitors in electric vehicles and high-speed trains. However, single-component polymers could not achieve these desired properties simultaneously. Polymer multilayer films (MLFs), which combine a high dielectric constant polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)] in a unique layered structure, have the potential achieve them at the same time. In this work, the effects of PC glass transition temperature (Tg) on the dielectric insulation properties (breakdown strength and lifetime) were investigated at high temperatures of 100-150 °C. Three PC materials had Tg values of 145 (PC1), 165 (PC2), and 185 °C (PC3), respectively. It is observed that MLF-PC3 with the highest Tg of PC exhibited the highest Weibull direct/alternating current (DC/AC) breakdown strength and the longest DC/AC lifetime, whereas MLF-PC1 with the lowest Tg showed the lowest Weibull DC/AC breakdown strength and the shortest DC/AC lifetime. A high-temperature high-volage leakage current study revealed that MLF-PC3 exhibited the lowest bulk conductivity at all temperatures under different electric fields. The knowledge obtained from this study will help us design better MLFs with high performance for next-generation miniaturized capacitors.
- 27 December 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (1) , 795-806
Effect of Glass Transition Temperature on Enhanced Dielectric Breakdown Strength and Lifetime of Multilayer Polymer Films
High temperature, high energy density, and low loss dielectric films are promising candidates for miniaturized capacitors in electric vehicles and high-speed trains. However, single-component polymers could not achieve these desired properties simultaneously. Polymer multilayer films (MLFs), which combine a high dielectric constant polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)] in a unique layered structure, have the potential achieve them at the same time. In this work, the effects of PC glass transition temperature (Tg) on the dielectric insulation properties (breakdown strength and lifetime) were investigated at high temperatures of 100-150 °C. Three PC materials had Tg values of 145 (PC1), 165 (PC2), and 185 °C (PC3), respectively. It is observed that MLF-PC3 with the highest Tg of PC exhibited the highest Weibull direct/alternating current (DC/AC) breakdown strength and the longest DC/AC lifetime, whereas MLF-PC1 with the lowest Tg showed the lowest Weibull DC/AC breakdown strength and the shortest DC/AC lifetime. A high-temperature high-volage leakage current study revealed that MLF-PC3 exhibited the lowest bulk conductivity at all temperatures under different electric fields. The knowledge obtained from this study will help us design better MLFs with high performance for next-generation miniaturized capacitors.
- Open Access
Oriented Tapes of Incompatible Polymers Using a Novel Multiplication Co-Extrusion Process
Continuous tapes of polypropylene (PP) and high-density polyethylene (HDPE) were produced using a novel multiplication co-extrusion process. The structure of the PP/HDPE tapes consists of co-continuous PP and HDPE domains aligned in the extrusion direction, forming a fiber-like composite structure with individual domain thicknesses of 200–500 nm. This unique structure created a significantly large contact interface between the polymer domains. AFM images suggest strong interfacial interactions between incompatible PP and HDPE domains. Orientation at 130 °C was possible due to the enhanced adhesion arising from epitaxial crystallization and the large interfacial area. The modulus, tensile strength, and orientation factor of the oriented composite tapes increased as the draw ratio increased. The existence of two independent shish kabab-like morphologies in the oriented tapes at different draw ratios was indicated by the appearance of two melting peaks for each material. After one-step orientation at 130 °C to a draw ratio of 25, the moduli of the oriented tapes increased to approximately 10 GPa, and the tensile strength increased to approximately 540 MPa. These oriented tapes are stiffer and stronger than commercial tapes and do not fibrillate during the orientation process indicating some interfacial interaction between the domains.
Open AccessOriented Tapes of Incompatible Polymers Using a Novel Multiplication Co-Extrusion Process
Continuous tapes of polypropylene (PP) and high-density polyethylene (HDPE) were produced using a novel multiplication co-extrusion process. The structure of the PP/HDPE tapes consists of co-continuous PP and HDPE domains aligned in the extrusion direction, forming a fiber-like composite structure with individual domain thicknesses of 200–500 nm. This unique structure created a significantly large contact interface between the polymer domains. AFM images suggest strong interfacial interactions between incompatible PP and HDPE domains. Orientation at 130 °C was possible due to the enhanced adhesion arising from epitaxial crystallization and the large interfacial area. The modulus, tensile strength, and orientation factor of the oriented composite tapes increased as the draw ratio increased. The existence of two independent shish kabab-like morphologies in the oriented tapes at different draw ratios was indicated by the appearance of two melting peaks for each material. After one-step orientation at 130 °C to a draw ratio of 25, the moduli of the oriented tapes increased to approximately 10 GPa, and the tensile strength increased to approximately 540 MPa. These oriented tapes are stiffer and stronger than commercial tapes and do not fibrillate during the orientation process indicating some interfacial interaction between the domains.
- 29 July 2022
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 55 (15) , 6562-6572
Multiscale Analysis of Segmental Relaxation in PC/PETg Multilayers: Evidence of Immiscible Nanodroplets
- 29 July 2022
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 55 (15) , 6562-6572
Multiscale Analysis of Segmental Relaxation in PC/PETg Multilayers: Evidence of Immiscible Nanodroplets
- 28 September 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (40) , 44892-44901
Achieving Flat-on Primary Crystals by Nanoconfined Crystallization in High-Temperature Polycarbonate/Poly(vinylidene fluoride) Multilayer Films and Its Effect on Dielectric Insulation
To meet the stringent requirements of next-generation film capacitors for power electronics, multilayer films (MLFs) are fabricated with the advantage of achieving high temperature rating, high energy density, and reasonably low loss simultaneously. In this study, a high permittivity polar polymer, poly(vinylidene fluoride) (PVDF), is multilayered with a linear, low loss dielectric polymer such as high-temperature polycarbonate (HTPC). However, the dielectric loss of these MLFs was still high as compared with current state-of-the-art biaxially oriented polypropylene (BOPP) films. The goal of this work is to decrease the dielectric loss and enhance dielectric insulation by achieving flat-on primary PVDF crystals in MLFs via nanoconfined melt-recrystallization. Based on simultaneous small- and wide-angle X-ray scattering experiments, edge-on lamellar crystals were observed for all as-extruded MLFs, regardless of different PVDF layer thicknesses. However, after melting at 180 °C followed by recrystallization, flat-on primary crystals were successfully achieved when the PVDF layer thickness was below 39 nm. Above 78 nm for the PVDF layer, major edge-on primary crystals with minor flat-on secondary crystals were observed. From leakage current, breakdown, lifetime, and electric displacement-electric field loop studies, MLFs with the flat-on primary crystals exhibited reduced loss and enhanced dielectric insulation as compared to as-extruded MLFs and those with edge-on primary/flat-on secondary crystals. This was attributed to the effective blockage of charge carriers by the flat-on PVDF primary crystals and their reduced ferroelectric switching.
- 28 September 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (40) , 44892-44901
Achieving Flat-on Primary Crystals by Nanoconfined Crystallization in High-Temperature Polycarbonate/Poly(vinylidene fluoride) Multilayer Films and Its Effect on Dielectric Insulation
To meet the stringent requirements of next-generation film capacitors for power electronics, multilayer films (MLFs) are fabricated with the advantage of achieving high temperature rating, high energy density, and reasonably low loss simultaneously. In this study, a high permittivity polar polymer, poly(vinylidene fluoride) (PVDF), is multilayered with a linear, low loss dielectric polymer such as high-temperature polycarbonate (HTPC). However, the dielectric loss of these MLFs was still high as compared with current state-of-the-art biaxially oriented polypropylene (BOPP) films. The goal of this work is to decrease the dielectric loss and enhance dielectric insulation by achieving flat-on primary PVDF crystals in MLFs via nanoconfined melt-recrystallization. Based on simultaneous small- and wide-angle X-ray scattering experiments, edge-on lamellar crystals were observed for all as-extruded MLFs, regardless of different PVDF layer thicknesses. However, after melting at 180 °C followed by recrystallization, flat-on primary crystals were successfully achieved when the PVDF layer thickness was below 39 nm. Above 78 nm for the PVDF layer, major edge-on primary crystals with minor flat-on secondary crystals were observed. From leakage current, breakdown, lifetime, and electric displacement-electric field loop studies, MLFs with the flat-on primary crystals exhibited reduced loss and enhanced dielectric insulation as compared to as-extruded MLFs and those with edge-on primary/flat-on secondary crystals. This was attributed to the effective blockage of charge carriers by the flat-on PVDF primary crystals and their reduced ferroelectric switching.
- 30 December 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 59 (12) , 5227-5237
Alkaline Battery Separators with High Electrolyte Absorption from Forced Assembly Coextruded Composite Tapes
- 30 December 2019
- Published by American Chemical Society (ACS) in Industrial & Engineering Chemistry Research
- Vol. 59 (12) , 5227-5237
Alkaline Battery Separators with High Electrolyte Absorption from Forced Assembly Coextruded Composite Tapes
- Open Access
Antimicrobial LDPE/EVOH Layered Films Containing Carvacrol Fabricated by Multiplication Extrusion
This work describes the fabrication of antimicrobial multilayered polymeric films containing carvacrol (used as a model essential oil) by co-extrusion and multiplication technique. The microlayering process was utilized to produce films, with up to 65 alternating layers, of carvacrol-containing low-density polyethylene (LDPE) and ethylene vinyl alcohol copolymer (EVOH). Carvacrol was melt compounded with LDPE or loaded into halloysite nanotubes (HNTs) in a pre-compounding step prior film production. The detailed nanostructure and composition (in terms of carvacrol content) of the films were characterized and correlated to their barrier properties, carvacrol release rate, and antibacterial and antifungal activity. The resulting films exhibit high carvacrol content despite the harsh processing conditions (temperature of 200 °C and long processing time), regardless of the number of layers or the presence of HNTs. The multilayered films exhibit superior oxygen transmission rates and carvacrol diffusivity values that are more than two orders of magnitude lower in comparison to single-layered carvacrol-containing films (i.e., LDPE/carvacrol and LDPE/(HNTs/carvacrol)) produced by conventional cast extrusion. The (LDPE/carvacrol)/EVOH and (LDPE/[HNTs/carvacrol])/EVOH films demonstrated excellent antimicrobial efficacy against E. coli and Alternaria alternata in in vitro micro-atmosphere assays and against A. alternata and Rhizopus in cherry tomatoes, used as the food model. The results presented here suggest that sensitive essential oils, such as carvacrol, can be incorporated into plastic polymers constructed of tailored multiple layers, without losing their antimicrobial efficacy.
Open AccessAntimicrobial LDPE/EVOH Layered Films Containing Carvacrol Fabricated by Multiplication Extrusion
This work describes the fabrication of antimicrobial multilayered polymeric films containing carvacrol (used as a model essential oil) by co-extrusion and multiplication technique. The microlayering process was utilized to produce films, with up to 65 alternating layers, of carvacrol-containing low-density polyethylene (LDPE) and ethylene vinyl alcohol copolymer (EVOH). Carvacrol was melt compounded with LDPE or loaded into halloysite nanotubes (HNTs) in a pre-compounding step prior film production. The detailed nanostructure and composition (in terms of carvacrol content) of the films were characterized and correlated to their barrier properties, carvacrol release rate, and antibacterial and antifungal activity. The resulting films exhibit high carvacrol content despite the harsh processing conditions (temperature of 200 °C and long processing time), regardless of the number of layers or the presence of HNTs. The multilayered films exhibit superior oxygen transmission rates and carvacrol diffusivity values that are more than two orders of magnitude lower in comparison to single-layered carvacrol-containing films (i.e., LDPE/carvacrol and LDPE/(HNTs/carvacrol)) produced by conventional cast extrusion. The (LDPE/carvacrol)/EVOH and (LDPE/[HNTs/carvacrol])/EVOH films demonstrated excellent antimicrobial efficacy against E. coli and Alternaria alternata in in vitro micro-atmosphere assays and against A. alternata and Rhizopus in cherry tomatoes, used as the food model. The results presented here suggest that sensitive essential oils, such as carvacrol, can be incorporated into plastic polymers constructed of tailored multiple layers, without losing their antimicrobial efficacy.
- 15 September 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (39) , 10417-10426
Enhanced dielectric properties due to space charge-induced interfacial polarization in multilayer polymer films
With the recent advancement of power electronics, polymer film capacitors have become increasingly important. However, the low temperature rating (up to 85 °C) and low energy density (5 J cm−3 at breakdown) of state-of-the-art biaxially oriented polypropylene (BOPP) films have been limiting factors for advanced power electronics. Based on our recent work, multilayer films (MLFs), which consist of a high energy density polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)], have shown potential to achieve high energy density (13–17 J cm−3), enhanced breakdown strength, high temperature tolerance, and low loss simultaneously. In this study, the dielectric properties of PC/PVDF 50/50 32- and 256-layer (32L and 256L) films were investigated. The breakdown strength of the 32L film was as high as 800 MV m−1 at room temperature, as compared to 600 MV m−1 of PVDF and 750 MV m−1 of PC. The temperature rating of the 32L film reached 120 °C, higher than that of BOPP. In addition, it was observed that the 32L film with thicker PC layers exhibited a higher breakdown strength and a lower DC conductivity than the 256L film with thinner PC layers at elevated temperatures. These differences were attributed to the difference in the interfacial polarization of space charges, which was further verified by thermally stimulated depolarization current spectroscopy. From this study, we conclude that interfacial polarization endows MLFs with the desirable dielectric properties for next generation film capacitors.
- 15 September 2017
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry C
- Vol. 5 (39) , 10417-10426
Enhanced dielectric properties due to space charge-induced interfacial polarization in multilayer polymer films
With the recent advancement of power electronics, polymer film capacitors have become increasingly important. However, the low temperature rating (up to 85 °C) and low energy density (5 J cm−3 at breakdown) of state-of-the-art biaxially oriented polypropylene (BOPP) films have been limiting factors for advanced power electronics. Based on our recent work, multilayer films (MLFs), which consist of a high energy density polymer [e.g., poly(vinylidene fluoride) (PVDF)] and a high breakdown/low loss polymer [e.g., polycarbonate (PC)], have shown potential to achieve high energy density (13–17 J cm−3), enhanced breakdown strength, high temperature tolerance, and low loss simultaneously. In this study, the dielectric properties of PC/PVDF 50/50 32- and 256-layer (32L and 256L) films were investigated. The breakdown strength of the 32L film was as high as 800 MV m−1 at room temperature, as compared to 600 MV m−1 of PVDF and 750 MV m−1 of PC. The temperature rating of the 32L film reached 120 °C, higher than that of BOPP. In addition, it was observed that the 32L film with thicker PC layers exhibited a higher breakdown strength and a lower DC conductivity than the 256L film with thinner PC layers at elevated temperatures. These differences were attributed to the difference in the interfacial polarization of space charges, which was further verified by thermally stimulated depolarization current spectroscopy. From this study, we conclude that interfacial polarization endows MLFs with the desirable dielectric properties for next generation film capacitors.
- 15 December 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (14)
Programming of macro/micro scale information on shape memorizing polyvinyl acetate film
The shape memory behavior of polyvinyl acetate (PVAc), both at macroscale and microscale, is presented. PVAc films exhibited excellent efficiency in programming macroscale deformation. Cyclic tensile tests on PVAc films revealed the importance of molecular weight in programming macroscale deformation in film. PVAc film with the highest molecular weight (∼228 kDa) exhibited maximum durability in programming macroscale deformation. This gives an important insight to the discovery of new shape memory polymers since chain entanglements in high molecular weight glassy polymers can impart shape memory behavior. In addition, such shape memory behavior can be exploited to imprint and tune microscale patterns on the film. Microprismatic patterns were embossed and programmed on shape memorizing PVAc films. Two different test methodologies were used to study the programmability of patterns on PVAc films. Pattern programming was significantly affected by the method used. In both cases, recovery time and temperature were two important parameters to determine the efficiency of programming. In addition, optical properties of PVAc films could be switched between reflective and transparent by programming patterns on the surface of the film. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44659.
- 15 December 2016
- Published by Wiley in Journal of Applied Polymer Science
- Vol. 134 (14)
Programming of macro/micro scale information on shape memorizing polyvinyl acetate film
The shape memory behavior of polyvinyl acetate (PVAc), both at macroscale and microscale, is presented. PVAc films exhibited excellent efficiency in programming macroscale deformation. Cyclic tensile tests on PVAc films revealed the importance of molecular weight in programming macroscale deformation in film. PVAc film with the highest molecular weight (∼228 kDa) exhibited maximum durability in programming macroscale deformation. This gives an important insight to the discovery of new shape memory polymers since chain entanglements in high molecular weight glassy polymers can impart shape memory behavior. In addition, such shape memory behavior can be exploited to imprint and tune microscale patterns on the film. Microprismatic patterns were embossed and programmed on shape memorizing PVAc films. Two different test methodologies were used to study the programmability of patterns on PVAc films. Pattern programming was significantly affected by the method used. In both cases, recovery time and temperature were two important parameters to determine the efficiency of programming. In addition, optical properties of PVAc films could be switched between reflective and transparent by programming patterns on the surface of the film. © 2016 Wiley Periodicals, Inc. J. Appl. Polym. Sci. 2017, 134, 44659.
- 24 September 2015
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (1) , 188-203
Processing-structure–property relationships of novel fibrous filters produced by a melt-process
- 24 September 2015
- Published by Springer Nature in Journal of Materials Science
- Vol. 51 (1) , 188-203
Processing-structure–property relationships of novel fibrous filters produced by a melt-process
- 22 April 2013
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 51 (12) , 978-991
Interphase/interface modification on the dielectric properties of polycarbonate/poly(vinylidene fluoride‐co‐hexafluoropropylene) multilayer films for high‐energy density capacitors
Unique three‐component multilayer films with ATBTATBTA configuration were fabricated using forced assembly multilayer coextrusion for novel dielectric systems. The dielectric breakdown strength, displacement–electric field hysteresis, and dielectric spectroscopy of 65‐layer polycarbonate (PC)/tie/poly(vinylidene fluoride‐co‐hexafluoropropylene) (P(VDF‐HFP)) were investigated with various tie materials. Three different tie materials, poly(methyl methacrylate) (PMMA), styrene‐co‐acrylonitrile copolymer with 30% acrylonitrile content (SAN30), and poly(ethylene terephthalate‐co‐1,4‐cycohexanedimethylene terephthalate) (PETG) were chosen owing to their various degrees of interaction with either P(VDF‐HFP) or PC. The 65‐layer PC/PMMA/P(VDF‐HFP) films exhibited a 25% enhancement in breakdown properties, 50% higher energy density, 40% smaller hysteresis loop areas, and orders of magnitude slower ion migration relative to the 33‐layer PC/P(VDF‐HFP) control. These property improvements are mainly attributed to the localized interactions at PMMA/P(VDF‐HFP) and PMMA/PC interfaces, forming interphase regions. The modified PMMA/P(VDF‐HFP) interphase region can effectively hinder the migration of impurity ions in P(VDF‐HFP), reducing their mobility within the layer. Additionally, a small fraction of PMMA can lead to slightly increased dielectric constant of the composite films owing to strong interaction between PMMA and P(VDF‐HFP). The other two systems with PETG and SAN30 as tie layers exhibited marginal improvements in dielectric properties owing to their weaker interactions with the P(VDF‐HFP) layers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 978–991
- 22 April 2013
- Published by Wiley in Journal of Polymer Science Part B: Polymer Physics
- Vol. 51 (12) , 978-991
Interphase/interface modification on the dielectric properties of polycarbonate/poly(vinylidene fluoride‐co‐hexafluoropropylene) multilayer films for high‐energy density capacitors
Unique three‐component multilayer films with ATBTATBTA configuration were fabricated using forced assembly multilayer coextrusion for novel dielectric systems. The dielectric breakdown strength, displacement–electric field hysteresis, and dielectric spectroscopy of 65‐layer polycarbonate (PC)/tie/poly(vinylidene fluoride‐co‐hexafluoropropylene) (P(VDF‐HFP)) were investigated with various tie materials. Three different tie materials, poly(methyl methacrylate) (PMMA), styrene‐co‐acrylonitrile copolymer with 30% acrylonitrile content (SAN30), and poly(ethylene terephthalate‐co‐1,4‐cycohexanedimethylene terephthalate) (PETG) were chosen owing to their various degrees of interaction with either P(VDF‐HFP) or PC. The 65‐layer PC/PMMA/P(VDF‐HFP) films exhibited a 25% enhancement in breakdown properties, 50% higher energy density, 40% smaller hysteresis loop areas, and orders of magnitude slower ion migration relative to the 33‐layer PC/P(VDF‐HFP) control. These property improvements are mainly attributed to the localized interactions at PMMA/P(VDF‐HFP) and PMMA/PC interfaces, forming interphase regions. The modified PMMA/P(VDF‐HFP) interphase region can effectively hinder the migration of impurity ions in P(VDF‐HFP), reducing their mobility within the layer. Additionally, a small fraction of PMMA can lead to slightly increased dielectric constant of the composite films owing to strong interaction between PMMA and P(VDF‐HFP). The other two systems with PETG and SAN30 as tie layers exhibited marginal improvements in dielectric properties owing to their weaker interactions with the P(VDF‐HFP) layers. © 2013 Wiley Periodicals, Inc. J. Polym. Sci., Part B: Polym. Phys. 2013, 51, 978–991