Maik Fröhlich
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Maik Fröhlich has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
C. Regula
Plasma Technology and Surfaces – PLATO, Fraunhofer Institute for Manufacturing Technology and Advanced Materials (IFAM), Bremen, Germany
1 shared publication- Christof Schröfl
Technische Universität Dresden
1 shared publication H. Kersten
Institute of Experimental and Applied Physics, Kiel University, Kiel, Germany
1 shared publication- Holger Kersten
Institute of Experimental and Applied Physics, University of Kiel , Leibnizstraße 19, 24098 Kiel
1 shared publication J. Ihde
Plasma Technology and Surfaces – PLATO, Fraunhofer Institute for Manufacturing Technology and Advanced Materials (IFAM), Bremen, Germany
1 shared publication- Kai Schneider
TU Dresden Institut für Baustoffe 01062 Dresden
1 shared publication
Latest Publications
- 22 May 2017
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 26 (6) , 065013
Calorimetric probe measurements for a high voltage pulsed substrate (PBII) in a HiPIMS process
The combination of high-power impulse magentron sputtering (HiPIMS) and plasma based ion implantation (PBII) gives a versatile system which allows successive and simultaneous coating, doping or cleaning of a substrate surface in a single process. The delay between HiPIMS and PBII pulse is a critical parameter for the synchronization of the pulses as it defines at what time during the HiPIMS period the high voltage is applied to the substrate. To investigate the effect of this parameter on the energy flux towards the PBII substrate, VI-probe and calorimetric probe measurements were performed illustrating the effect of the delay for different PBII pulse durations and PBII voltages. The calorimetric measurements were performed utilizing a grid setup which allowed us to derive conclusions even when using a detector that is not at the PBII voltage. A maximum of electrical power and energy flux was observed for delay times significantly longer than the duration of the HiPIMS pulse. The investigation of different PBII pulse durations and PBII voltages confirmed that these parameters affect the absolute values of the energy flux and electrical power but do not significantly affect the transport of the ions as the PBII potential is shielded by a sheath.
- 22 May 2017
- Published by IOP Publishing in Plasma Sources Science and Technology
- Vol. 26 (6) , 065013
Calorimetric probe measurements for a high voltage pulsed substrate (PBII) in a HiPIMS process
The combination of high-power impulse magentron sputtering (HiPIMS) and plasma based ion implantation (PBII) gives a versatile system which allows successive and simultaneous coating, doping or cleaning of a substrate surface in a single process. The delay between HiPIMS and PBII pulse is a critical parameter for the synchronization of the pulses as it defines at what time during the HiPIMS period the high voltage is applied to the substrate. To investigate the effect of this parameter on the energy flux towards the PBII substrate, VI-probe and calorimetric probe measurements were performed illustrating the effect of the delay for different PBII pulse durations and PBII voltages. The calorimetric measurements were performed utilizing a grid setup which allowed us to derive conclusions even when using a detector that is not at the PBII voltage. A maximum of electrical power and energy flux was observed for delay times significantly longer than the duration of the HiPIMS pulse. The investigation of different PBII pulse durations and PBII voltages confirmed that these parameters affect the absolute values of the energy flux and electrical power but do not significantly affect the transport of the ions as the PBII potential is shielded by a sheath.
- Open Access
Mineral-Based Coating of Plasma-Treated Carbon Fibre Rovings for Carbon Concrete Composites with Enhanced Mechanical Performance
Surfaces of carbon fibre roving were modified by means of a low temperature plasma treatment to improve their bonding with mineral fines; the latter serving as an inorganic fibre coating for the improved mechanical performance of carbon reinforcement in concrete matrices. Variation of the plasma conditions, such as gas composition and treatment time, was accomplished to establish polar groups on the carbon fibres prior to contact with the suspension of mineral particles in water. Subsequently, the rovings were implemented in a fine concrete matrix and their pull-out performance was assessed. Every plasma treatment resulted in increased pull-out forces in comparison to the reference samples without plasma treatment, indicating a better bonding between the mineral coating material and the carbon fibres. Significant differences were found, depending on gas composition and treatment time. Microscopic investigations showed that the samples with the highest pull-out force exhibited carbon fibre surfaces with the largest areas of hydration products grown on them. Additionally, the coating material ingresses into the multifilament roving in these specimens, leading to better force transfer between individual carbon filaments and between the entire roving and surrounding matrix, thus explaining the superior mechanical performance of the specimens containing appropriately plasma-treated carbon roving.
Open AccessMineral-Based Coating of Plasma-Treated Carbon Fibre Rovings for Carbon Concrete Composites with Enhanced Mechanical Performance
Surfaces of carbon fibre roving were modified by means of a low temperature plasma treatment to improve their bonding with mineral fines; the latter serving as an inorganic fibre coating for the improved mechanical performance of carbon reinforcement in concrete matrices. Variation of the plasma conditions, such as gas composition and treatment time, was accomplished to establish polar groups on the carbon fibres prior to contact with the suspension of mineral particles in water. Subsequently, the rovings were implemented in a fine concrete matrix and their pull-out performance was assessed. Every plasma treatment resulted in increased pull-out forces in comparison to the reference samples without plasma treatment, indicating a better bonding between the mineral coating material and the carbon fibres. Significant differences were found, depending on gas composition and treatment time. Microscopic investigations showed that the samples with the highest pull-out force exhibited carbon fibre surfaces with the largest areas of hydration products grown on them. Additionally, the coating material ingresses into the multifilament roving in these specimens, leading to better force transfer between individual carbon filaments and between the entire roving and surrounding matrix, thus explaining the superior mechanical performance of the specimens containing appropriately plasma-treated carbon roving.
- 11 February 2014
- Published by Wiley in Contributions to Plasma Physics
- Vol. 54 (2) , 155-161
Determination of the Energy Flux of a Commercial Atmospheric‐Pressure Plasma Jet for Different Process Gases and Distances Between Nozzle Outlet and Substrate Surface
The energy flux of an atmospheric‐pressure plasma jet for surface treatment has been investigated by a calorimetric probe. Generally, the investigations exhibit that the main contributions of the total energy influx from the plasma to the substrate surface originate from the neutrals regarding high gas temperature coupled with a high gas flow. The use of nitrogen as process gas shows a higher energy flux compared to oxygen and air presumably caused by increased gas temperature as well as by higher molecule formation and recombination energy of N2. Moreover, the lateral expansion of the plasma beam could be roughly determined by a spatially resolved analysis of the energy influx. A top part mounted on the nozzle, commonly used for the injection of additional precursor gases, showed a significant effect on the flow behavior and collision entailed relaxation of the excited plasma species leading to a restraining of the plasma jet.
- 11 February 2014
- Published by Wiley in Contributions to Plasma Physics
- Vol. 54 (2) , 155-161
Determination of the Energy Flux of a Commercial Atmospheric‐Pressure Plasma Jet for Different Process Gases and Distances Between Nozzle Outlet and Substrate Surface
The energy flux of an atmospheric‐pressure plasma jet for surface treatment has been investigated by a calorimetric probe. Generally, the investigations exhibit that the main contributions of the total energy influx from the plasma to the substrate surface originate from the neutrals regarding high gas temperature coupled with a high gas flow. The use of nitrogen as process gas shows a higher energy flux compared to oxygen and air presumably caused by increased gas temperature as well as by higher molecule formation and recombination energy of N2. Moreover, the lateral expansion of the plasma beam could be roughly determined by a spatially resolved analysis of the energy influx. A top part mounted on the nozzle, commonly used for the injection of additional precursor gases, showed a significant effect on the flow behavior and collision entailed relaxation of the excited plasma species leading to a restraining of the plasma jet.