Chenglian He
Chenglian He has a total of 17 co-authors. Here are the top co-authors by number of shared publications:
- Fujun Wang
College of Water Resources & Civil Engineering, China Agricultural University, Beijing 100083, China
3 shared publications - Ruofu Xiao
College of Water Resources and Intelligence Engineering, China Agricultural University, Beijing 100083, China
2 shared publications - Zhifeng Yao
College of Water Resources and Civil Engineering, China Agricultural University, Beijing, China
2 shared publications - Chaoyue Wang
College of Water Resources and Civil Engineering, China Agricultural University, Beijing 100083, China
1 shared publication - Congbing Huang
Jiangsu Aerospace Hydraulic Equipment Co., Ltd., Yangzhou 225699, China
1 shared publication Dan Zi
College of Water Resources and Civil Engineering, China Agricultural University, Beijing 100083, China
1 shared publication
Latest Publications
- 24 January 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (4)
Investigation Into the Phenomenon of Flow Deviation in the S-Shaped Discharge Passage of a Slanted Axial-Flow Pumping System
A remarkable flow deviation phenomenon exists in the S-shaped discharge passage of a slanted axial-flow pumping system. In order to reveal the characteristics and development process of the deviating flow, numerical simulation was performed for a 15 deg slanted axial-flow pumping system, and the deviating flow was measured on an experimental rig. The details of the deviating flow in the S-shaped discharge passage were obtained. A kind of “unwinding” flow structure similar to that of DNA in biology is found in the S-shaped passage. The special structure is characterized by a “single strand” in which original helical streamlines are almost straightened. The bulk speed of the fluids on the “single strand” on the left side of the passage significantly increases while the swirling strength and the kinetic pressure ratio decrease. Large-scale Dean vortices at the passage bottom interact with high transverse energy gradient fluids at the passage top as water flows into the convex part of the S-shaped passage, which leads to the emergence of the “unwinding” structure. Reverse secondary flows further enlarge the scale of the Dean vortices as water flows into the concave part of the S-shaped passage, which results in the growth of the “unwinding” structure. With the development of the asymmetrical flow structure, an irreversible severe flow deviation problem naturally comes into being.
- 24 January 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (4)
Investigation Into the Phenomenon of Flow Deviation in the S-Shaped Discharge Passage of a Slanted Axial-Flow Pumping System
A remarkable flow deviation phenomenon exists in the S-shaped discharge passage of a slanted axial-flow pumping system. In order to reveal the characteristics and development process of the deviating flow, numerical simulation was performed for a 15 deg slanted axial-flow pumping system, and the deviating flow was measured on an experimental rig. The details of the deviating flow in the S-shaped discharge passage were obtained. A kind of “unwinding” flow structure similar to that of DNA in biology is found in the S-shaped passage. The special structure is characterized by a “single strand” in which original helical streamlines are almost straightened. The bulk speed of the fluids on the “single strand” on the left side of the passage significantly increases while the swirling strength and the kinetic pressure ratio decrease. Large-scale Dean vortices at the passage bottom interact with high transverse energy gradient fluids at the passage top as water flows into the convex part of the S-shaped passage, which leads to the emergence of the “unwinding” structure. Reverse secondary flows further enlarge the scale of the Dean vortices as water flows into the concave part of the S-shaped passage, which results in the growth of the “unwinding” structure. With the development of the asymmetrical flow structure, an irreversible severe flow deviation problem naturally comes into being.
- 24 January 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (4)
Experimental Investigation on Pressure Fluctuation Reduction in a Double Suction Centrifugal Pump: Influence of Impeller Stagger and Blade Geometry
The reduction in pressure fluctuation can suppress noise, balance the radial and axial forces, and restrain the vibration level of a centrifugal pump. Impeller stagger and blade geometry influence the pressure fluctuation characteristics of double suction centrifugal pumps. In the present investigation, the pressure fluctuation characteristics of the baseline impeller, the staggered impeller, and the blade geometry modified impeller were investigated experimentally under design and off-design operating conditions. The frequency spectrum was analyzed by fast Fourier transform (FFT) and continuous wavelet transform (CWT) methods. The broadband frequencies are defined quantitatively and analyzed emphatically. The significant linear relationship between the center frequency of the broadband frequencies and the flowrate is discovered for the first time. The center frequency decreases as the flowrate increases. The linearity varies below and above the design flowrate. When the discrete frequencies are in range of the broadband frequencies, a high amplitude of pressure fluctuation occurs. This could explain the large peak-to-peak value of the pressure fluctuation at 1.24Qn, which may be due to the coincidence between broadband frequencies and the components at the frequencies fr and 2fr. Both the staggered impeller and the blade geometry modified impeller can reduce the level of pressure fluctuation; in particular, it is reduced to 35% and 13% compared to that of baseline impeller near the volute tongue region under the design flowrate, respectively. The staggered impeller and the blade geometry can obviously affect the decreasing slopes between the center frequencies and the flowrate.
- 24 January 2020
- Published by ASME International in Journal of Fluids Engineering
- Vol. 142 (4)
Experimental Investigation on Pressure Fluctuation Reduction in a Double Suction Centrifugal Pump: Influence of Impeller Stagger and Blade Geometry
The reduction in pressure fluctuation can suppress noise, balance the radial and axial forces, and restrain the vibration level of a centrifugal pump. Impeller stagger and blade geometry influence the pressure fluctuation characteristics of double suction centrifugal pumps. In the present investigation, the pressure fluctuation characteristics of the baseline impeller, the staggered impeller, and the blade geometry modified impeller were investigated experimentally under design and off-design operating conditions. The frequency spectrum was analyzed by fast Fourier transform (FFT) and continuous wavelet transform (CWT) methods. The broadband frequencies are defined quantitatively and analyzed emphatically. The significant linear relationship between the center frequency of the broadband frequencies and the flowrate is discovered for the first time. The center frequency decreases as the flowrate increases. The linearity varies below and above the design flowrate. When the discrete frequencies are in range of the broadband frequencies, a high amplitude of pressure fluctuation occurs. This could explain the large peak-to-peak value of the pressure fluctuation at 1.24Qn, which may be due to the coincidence between broadband frequencies and the components at the frequencies fr and 2fr. Both the staggered impeller and the blade geometry modified impeller can reduce the level of pressure fluctuation; in particular, it is reduced to 35% and 13% compared to that of baseline impeller near the volute tongue region under the design flowrate, respectively. The staggered impeller and the blade geometry can obviously affect the decreasing slopes between the center frequencies and the flowrate.
- Open Access
Experimental Investigation of Transient Characteristics of a Double Suction Centrifugal Pump System during Starting Period
The starting phase for pumps in water transportation pipelines is crucial and has significant transient characteristics which merit further study in order to evaluate the operational stability of the pumping system. This paper presents the results of a study in which the relative steady operating conditions and starting period of a large double-suction centrifugal pump were monitored in real time, including pressure fluctuations, shaft run-out and vibration at the bearing. The transient characteristics of a double-suction centrifugal pump under different operating conditions have been analyzed using fast Fourier transform (FFT) and continuous wavelet transform (CWT). Results indicate broadband frequency components within the spectrum of pressure fluctuations in the volute casing under all test conditions, and the central frequency of the broadband frequency gradually decreases as flow rate increases and approaches the blade frequency, which is the primary reason for an increase in blade-frequency amplitude. This may produce a vibration frequency that is similar to the natural frequency of a certain part of the double-suction centrifugal pump during the starting period, which causes the resonance phenomenon. The radial force is also large during the starting period, which causes eccentric wear of the seal ring at the impeller inlet.
Open AccessExperimental Investigation of Transient Characteristics of a Double Suction Centrifugal Pump System during Starting Period
The starting phase for pumps in water transportation pipelines is crucial and has significant transient characteristics which merit further study in order to evaluate the operational stability of the pumping system. This paper presents the results of a study in which the relative steady operating conditions and starting period of a large double-suction centrifugal pump were monitored in real time, including pressure fluctuations, shaft run-out and vibration at the bearing. The transient characteristics of a double-suction centrifugal pump under different operating conditions have been analyzed using fast Fourier transform (FFT) and continuous wavelet transform (CWT). Results indicate broadband frequency components within the spectrum of pressure fluctuations in the volute casing under all test conditions, and the central frequency of the broadband frequency gradually decreases as flow rate increases and approaches the blade frequency, which is the primary reason for an increase in blade-frequency amplitude. This may produce a vibration frequency that is similar to the natural frequency of a certain part of the double-suction centrifugal pump during the starting period, which causes the resonance phenomenon. The radial force is also large during the starting period, which causes eccentric wear of the seal ring at the impeller inlet.
- Open Access
Optimization of the Runner for Extremely Low Head Bidirectional Tidal Bulb Turbine
This paper presents a multi-objective optimization procedure for bidirectional bulb turbine runners which is completed using ANSYS Workbench. The optimization procedure is able to check many more geometries with less manual work. In the procedure, the initial blade shape is parameterized, the inlet and outlet angles (β1, β2), as well as the starting and ending wrap angles (θ1, θ2) for the five sections of the blade profile, are selected as design variables, and the optimization target is set to obtain the maximum of the overall efficiency for the ebb and flood turbine modes. For the flow analysis, the ANSYS CFX code, with a SST (Shear Stress Transport) k-ω turbulence model, has been used to evaluate the efficiency of the turbine. An efficient response surface model relating the design parameters and the objective functions is obtained. The optimization strategy was used to optimize a model bulb turbine runner. Model tests were carried out to validate the final designs and the design procedure. For the four-bladed turbine, the efficiency improvement is 5.5% in the ebb operation direction, and 2.9% in the flood operation direction, as well as 4.3% and 4.5% for the three-bladed turbine. Numerical simulations were then performed to analyze the pressure pulsation in the pressure and suction sides of the blade for the prototype turbine with optimal four-bladed and three-bladed runners. The results show that the runner rotational frequency (fn) is the dominant frequency of the pressure pulsations in the blades for ebb and flood turbine modes, and the gravitational effect, rather than rotor-stator interaction (RSI), plays an important role in a low head horizontal axial turbine. The amplitudes of the pressure pulsations on the blade side facing the guide vanes varies little with the water head. However, the amplitudes of the pressure pulsations on the blade side facing the diffusion tube linearly increase with the water head. These results could provide valuable insight for reducing the pressure amplitudes in the bidirectional bulb turbine.
Open AccessOptimization of the Runner for Extremely Low Head Bidirectional Tidal Bulb Turbine
This paper presents a multi-objective optimization procedure for bidirectional bulb turbine runners which is completed using ANSYS Workbench. The optimization procedure is able to check many more geometries with less manual work. In the procedure, the initial blade shape is parameterized, the inlet and outlet angles (β1, β2), as well as the starting and ending wrap angles (θ1, θ2) for the five sections of the blade profile, are selected as design variables, and the optimization target is set to obtain the maximum of the overall efficiency for the ebb and flood turbine modes. For the flow analysis, the ANSYS CFX code, with a SST (Shear Stress Transport) k-ω turbulence model, has been used to evaluate the efficiency of the turbine. An efficient response surface model relating the design parameters and the objective functions is obtained. The optimization strategy was used to optimize a model bulb turbine runner. Model tests were carried out to validate the final designs and the design procedure. For the four-bladed turbine, the efficiency improvement is 5.5% in the ebb operation direction, and 2.9% in the flood operation direction, as well as 4.3% and 4.5% for the three-bladed turbine. Numerical simulations were then performed to analyze the pressure pulsation in the pressure and suction sides of the blade for the prototype turbine with optimal four-bladed and three-bladed runners. The results show that the runner rotational frequency (fn) is the dominant frequency of the pressure pulsations in the blades for ebb and flood turbine modes, and the gravitational effect, rather than rotor-stator interaction (RSI), plays an important role in a low head horizontal axial turbine. The amplitudes of the pressure pulsations on the blade side facing the guide vanes varies little with the water head. However, the amplitudes of the pressure pulsations on the blade side facing the diffusion tube linearly increase with the water head. These results could provide valuable insight for reducing the pressure amplitudes in the bidirectional bulb turbine.