Jérôme Luc
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Jérôme Luc has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Alexandre Lefrançois
CEA, DAM, GRAMAT, BP 80200, 46500 Gramat, France
3 shared publications - Antoine Osmont
CEA, DAM, GRAMAT, BP 80200, 46500 Gramat, France
2 shared publications - Sylvain Magne
Université Paris-Saclay, CEA, List
2 shared publications - Vincent Chuzeville
CEA, DAM, GRAMAT, BP 80200, 46500 Gramat, France
2 shared publications - Yohan Barbarin
CEA, DAM, GRAMAT, BP 80200, 46500 Gramat, France
2 shared publications - André Ferrand
Institut Clément Ader (ICA), Université de Toulouse, Modeling of Systems and Mechanical Microsystems (MS2M), 31400 Toulouse, France
1 shared publication
Latest Publications
- Open Access
Fiber Bragg Grating Dynamic Sensing Through a Dispersive Spectrometer
In the field of shock physics and energetic materials, Fiber Bragg Gratings (FBGs) are used to measure shock velocity, detonation velocity and shock pressure levels. They are also used to measure strain in structures loaded with explosive effects. FBG sensors are known to be light, small, immune electromagnetic environments and have fast response compared to electrical sensors. To use one or more gratings along a fiber, a high-resolution spectrometer with a high sampling rate has been developed. This dynamic spectrometer employs time-multiplexing by wavelength-to-time conversion using dispersion. It provides a complete view of the spectra evolution at a rate of 100 MHz. Thus, complex phenomena can be observed. In this paper, the interrogation technique is presented in more detail, and experimental results are discussed. The experiments presented are a low-pressure shock velocity measurement in epoxy, a deflagration-to-detonation transition in a porous energetic material, a Shock-to-Detonation Transition in a dense energetic material, a tentative-to-measure pressure level in epoxy from an FBG made in a sapphire fiber and multi-point strain measurements up to eight FBGs. The advantages and limits are discussed for each type of experiment.
Open AccessFiber Bragg Grating Dynamic Sensing Through a Dispersive Spectrometer
In the field of shock physics and energetic materials, Fiber Bragg Gratings (FBGs) are used to measure shock velocity, detonation velocity and shock pressure levels. They are also used to measure strain in structures loaded with explosive effects. FBG sensors are known to be light, small, immune electromagnetic environments and have fast response compared to electrical sensors. To use one or more gratings along a fiber, a high-resolution spectrometer with a high sampling rate has been developed. This dynamic spectrometer employs time-multiplexing by wavelength-to-time conversion using dispersion. It provides a complete view of the spectra evolution at a rate of 100 MHz. Thus, complex phenomena can be observed. In this paper, the interrogation technique is presented in more detail, and experimental results are discussed. The experiments presented are a low-pressure shock velocity measurement in epoxy, a deflagration-to-detonation transition in a porous energetic material, a Shock-to-Detonation Transition in a dense energetic material, a tentative-to-measure pressure level in epoxy from an FBG made in a sapphire fiber and multi-point strain measurements up to eight FBGs. The advantages and limits are discussed for each type of experiment.
- Open Access
Development of a Shock and Detonation Velocity Measurement System Using Chirped Fiber Bragg Gratings
Dynamic measurements of shock and detonation velocities are performed using long chirped fiber Bragg gratings (CFBGs). Such thin probes, with a diameter of typically 125 µm or even 80 µm can be directly inserted into high-explosive (HE) samples or simply glued laterally. During the detonation, the width of the optical spectrum is continuously reduced by the propagation of the wave-front, which physically shortens the CFBG. The light power reflected back shows a ramp-down type signal, from which the wave-front position is obtained as a function of time, thus yielding a detonation velocity profile. A calibration procedure was developed, with the support of optical simulations, to cancel out the optical spectrum distortions from the different optical components and to determine the wavelength-position transfer function of the CFBG. The fitted slopes of the X–T diagram give steady detonation velocity values which are in very good agreement with the classical measurements obtained from discrete electrical shorting pins (ESP). The main parameters influencing the uncertainties on the steady detonation velocity value measured by CFBG are discussed. To conclude, different HE experimental configurations tested at CEA (Commissariat à l’Energie Atomique et aux Energies Alternatives) are presented: bare cylindrical sticks, wedges for shock-to-detonation transitions (SDT), spheres, a cast-cured stick around a CFBG, and a detonation wave-front profile configuration.
Open AccessDevelopment of a Shock and Detonation Velocity Measurement System Using Chirped Fiber Bragg Gratings
Dynamic measurements of shock and detonation velocities are performed using long chirped fiber Bragg gratings (CFBGs). Such thin probes, with a diameter of typically 125 µm or even 80 µm can be directly inserted into high-explosive (HE) samples or simply glued laterally. During the detonation, the width of the optical spectrum is continuously reduced by the propagation of the wave-front, which physically shortens the CFBG. The light power reflected back shows a ramp-down type signal, from which the wave-front position is obtained as a function of time, thus yielding a detonation velocity profile. A calibration procedure was developed, with the support of optical simulations, to cancel out the optical spectrum distortions from the different optical components and to determine the wavelength-position transfer function of the CFBG. The fitted slopes of the X–T diagram give steady detonation velocity values which are in very good agreement with the classical measurements obtained from discrete electrical shorting pins (ESP). The main parameters influencing the uncertainties on the steady detonation velocity value measured by CFBG are discussed. To conclude, different HE experimental configurations tested at CEA (Commissariat à l’Energie Atomique et aux Energies Alternatives) are presented: bare cylindrical sticks, wedges for shock-to-detonation transitions (SDT), spheres, a cast-cured stick around a CFBG, and a detonation wave-front profile configuration.
- Open Access
- 18 December 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 727
Dynamic Mechanical Simulation of Miniature Silicon Membrane during Air Blast for Pressure Measurement
The development of new ultra-fast sensors for pressure air blast monitoring requires taking into account the very short rise time of pressure occurring during explosion. Simulations show here that the dynamic mechanical behavior of membrane-based sensors depends significantly on this rise time when the fundamental mechanical resonant frequency of the membrane is higher than 10 MHz.
- 18 December 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 727
Open AccessDynamic Mechanical Simulation of Miniature Silicon Membrane during Air Blast for Pressure Measurement
The development of new ultra-fast sensors for pressure air blast monitoring requires taking into account the very short rise time of pressure occurring during explosion. Simulations show here that the dynamic mechanical behavior of membrane-based sensors depends significantly on this rise time when the fundamental mechanical resonant frequency of the membrane is higher than 10 MHz.