Omar Kassem
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Omar Kassem has a total of 6 co-authors. Here are the top co-authors by number of shared publications:
- Jean-Paul Viricelle
Mines Saint-Étienne, Univ Lyon, CNRS, UMR 5307 LGF, Centre SPIN, F-42023 Saint-Etienne, France
3 shared publications - Mathilde Rieu
Mines Saint-Étienne, Univ Lyon, CNRS, UMR 5307 LGF, Centre SPIN, F-42023 Saint-Etienne, France
3 shared publications - Mohamed Saadaoui
Ecole Nationale Supérieure des Mines de Saint Etienne, CMP-EMSE, F-13048 Gardanne, France
3 shared publications - Christophe Pijolat
Ecole Nationale Supérieure des Mines, SPIN-EMSE, CNRS: UMR5307, LGF, F-42023 Saint-Etienne, France
1 shared publication - Mohamad Hijazi
École Nationale Supérieure des Mines, SPIN-EMSE, CNRS:UMR5307, LGF, F-42023 Saint-Étienne, France
1 shared publication - Valérie Stambouli
LMGP, Université Grenoble-Alpes, Grenoble INP-MINATEC, CS 50257, 38016 Grenoble Cedex 1, France
1 shared publication
Latest Publications
- Open Access
- 7 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 2
Functionalized SnO2 Sensors on Flexible Substrate for Ammonia Detection at Low Temperature
Ammonia detection at ambient with low-cost sensors is a challenge for various applications like breath analysis and agriculture. Such a challenge can be reached with functionalized SnO2 based gas sensors using silanization by 3-aminopropyltriethoxysilane (APTES) as an intermediate step before grafting with functional end group providing selectivity for the target gas. Moreover, operation at room temperature gives the opportunity to develop a sensor on a plastic substrate entirely manufactured by inkjet technology, by developing suitable inks, in particular to obtain SnO2 sensing element.
- 7 December 2020
- Published by MDPI AG in Proceedings
- Vol. 56 (1) , 2
Open AccessFunctionalized SnO2 Sensors on Flexible Substrate for Ammonia Detection at Low Temperature
Ammonia detection at ambient with low-cost sensors is a challenge for various applications like breath analysis and agriculture. Such a challenge can be reached with functionalized SnO2 based gas sensors using silanization by 3-aminopropyltriethoxysilane (APTES) as an intermediate step before grafting with functional end group providing selectivity for the target gas. Moreover, operation at room temperature gives the opportunity to develop a sensor on a plastic substrate entirely manufactured by inkjet technology, by developing suitable inks, in particular to obtain SnO2 sensing element.
- Open Access
- 26 November 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 907
Fabrication of SnO2 Flexible Sensor by Inkjet Printing Technology
In this work, a flexible tin oxide (SnO2) gas sensor was successfully fabricated by inkjet printing technology. This thin film deposition technique requires the formulation of stable suspensions with specific fluidic properties. Aqueous Sol-gel method was applied to synthesize a stable sol based on tin oxide, then transformed into ink with the appropriate viscosity and surface tension to be printed using a drop-on-demand piezoelectric inkjet printer. Thermal analyses of synthetized sol show that a crystallized structure of SnO2 could be obtained at 350 °C, which is lower than crystallization temperatures of SnO2 previously reported in the literature, and entirely consistent with our plastic substrate. The printed thin-film was then sintered at 350 °C on polyimide foil (Upilex-50S) and characterized as sensor.
- 26 November 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (13) , 907
Open AccessFabrication of SnO2 Flexible Sensor by Inkjet Printing Technology
In this work, a flexible tin oxide (SnO2) gas sensor was successfully fabricated by inkjet printing technology. This thin film deposition technique requires the formulation of stable suspensions with specific fluidic properties. Aqueous Sol-gel method was applied to synthesize a stable sol based on tin oxide, then transformed into ink with the appropriate viscosity and surface tension to be printed using a drop-on-demand piezoelectric inkjet printer. Thermal analyses of synthetized sol show that a crystallized structure of SnO2 could be obtained at 350 °C, which is lower than crystallization temperatures of SnO2 previously reported in the literature, and entirely consistent with our plastic substrate. The printed thin-film was then sintered at 350 °C on polyimide foil (Upilex-50S) and characterized as sensor.
- Open Access
- 8 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 622
Synthesis and Inkjet Printing of SnO2 Ink on a Flexible Substrate for Gas Sensor Application
Sol based SnO2 precursor was synthetized by aqueous sol-gel route, then transformed into a stable ink with appropriate viscosity and surface tension to be inkjet printed and sintered at relatively moderate temperature. Plastic foil with thickness of 50 μm was selected as substrate for its high thermal resistance and stability (Upilex-50S). Prepared sol and formulated ink were both characterized by analytical techniques; electrical measurements were performed on the printed sensing film to characterize the response to CO gas in different concentrations, at working temperature of 300 °C.
- 8 August 2017
- Published by MDPI AG in Proceedings
- Vol. 1 (4) , 622
Open AccessSynthesis and Inkjet Printing of SnO2 Ink on a Flexible Substrate for Gas Sensor Application
Sol based SnO2 precursor was synthetized by aqueous sol-gel route, then transformed into a stable ink with appropriate viscosity and surface tension to be inkjet printed and sintered at relatively moderate temperature. Plastic foil with thickness of 50 μm was selected as substrate for its high thermal resistance and stability (Upilex-50S). Prepared sol and formulated ink were both characterized by analytical techniques; electrical measurements were performed on the printed sensing film to characterize the response to CO gas in different concentrations, at working temperature of 300 °C.