Alexander E. Kalmykov
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Alexander E. Kalmykov has a total of 38 co-authors. Here are the top co-authors by number of shared publications:
L. M. Sorokin
Ioffe Institute, St. Petersburg, Russia
8 shared publications- Sergey A. Kukushkin
Institute for Problems in Mechanical Engineering of the Russian Academy of Sciences, St. Petersburg, Russia
3 shared publications V. I. Sokolov
Russian Academy of Sciences
3 shared publicationsA. V. Myasoedov
Ioffe Institute, St. Petersburg, Russia
2 shared publications- Alexander V. Myasoedov
Ioffe Institute
2 shared publications - Andrey V. Osipov
Institute for Problems in Mechanical Engineering of the Russian Academy of Science, 61 Boljshoy prospekt V.O., St. Petersburg 199178, Russian Federation
2 shared publications
Latest Publications
- 1 April 2024
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 58 (4) , 323-326
Dislocation Structure of AlN/SiC Templates Grown by Sublimation
The dislocation structure of an AlN layer grown on a SiC substrate by sublimation was studied using transmission electron microscopy. The peculiarity of the growth method was the evaporation of the substrate during the growth of the layer to prevent its cracking. The purpose of the study was to identify the sources of threading dislocations in the AlN layer. Dislocation superjogs, which are sources of dislocations, were found in the layer. A connection between the formation of superjogs and the procedure of substrate evaporation is assumed.
- 1 April 2024
- Published by Pleiades Publishing Ltd in Semiconductors
- Vol. 58 (4) , 323-326
Dislocation Structure of AlN/SiC Templates Grown by Sublimation
The dislocation structure of an AlN layer grown on a SiC substrate by sublimation was studied using transmission electron microscopy. The peculiarity of the growth method was the evaporation of the substrate during the growth of the layer to prevent its cracking. The purpose of the study was to identify the sources of threading dislocations in the AlN layer. Dislocation superjogs, which are sources of dislocations, were found in the layer. A connection between the formation of superjogs and the procedure of substrate evaporation is assumed.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S1) , S34-S37
The Effect of AlN Buffer Layer Morphology on the Structural Quality of a Semipolar GaN Layer Grown on a Si(001) Substrate, According to Transmission Electron Microscopy Data
Structural features of the interface between a semipolar gallium nitride layer and buffer layer of aluminum nitride grown on a SiC/Si(001) template misoriented by an angle of 7° were studied by high-resolution transmission electron microscopy. The effect of interface morphology on the structural quality of the gallium nitride layer was revealed: faceted structure of the buffer layer surface reduces the threading dislocations density.
- 1 December 2023
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 49 (S1) , S34-S37
The Effect of AlN Buffer Layer Morphology on the Structural Quality of a Semipolar GaN Layer Grown on a Si(001) Substrate, According to Transmission Electron Microscopy Data
Structural features of the interface between a semipolar gallium nitride layer and buffer layer of aluminum nitride grown on a SiC/Si(001) template misoriented by an angle of 7° were studied by high-resolution transmission electron microscopy. The effect of interface morphology on the structural quality of the gallium nitride layer was revealed: faceted structure of the buffer layer surface reduces the threading dislocations density.
- 1 December 2021
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 47 (12) , 893-896
Structural Characterization of a Short-Period Superlattice Based on the CdF2/CaF2/Si(111) Heterostructure by Transmission Electron Microscopy and X-Ray Diffractometry
A detailed study of the structure of a short-period superlattice based on alternating layers of cadmium and calcium fluorides grown by molecular beam epitaxy on a silicon substrate (111) by transmission electron microscopy and X-ray diffractometry has been performed. It has been established that the superlattice is in a pseudomorphic state and a lateral inhomogeneity with a fragment size of 10–40 nm has been found. The reason for the broadening of the main and satellite peaks of the superlattice on the diffraction curve (111) has been elucidated.
- 1 December 2021
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 47 (12) , 893-896
Structural Characterization of a Short-Period Superlattice Based on the CdF2/CaF2/Si(111) Heterostructure by Transmission Electron Microscopy and X-Ray Diffractometry
A detailed study of the structure of a short-period superlattice based on alternating layers of cadmium and calcium fluorides grown by molecular beam epitaxy on a silicon substrate (111) by transmission electron microscopy and X-ray diffractometry has been performed. It has been established that the superlattice is in a pseudomorphic state and a lateral inhomogeneity with a fragment size of 10–40 nm has been found. The reason for the broadening of the main and satellite peaks of the superlattice on the diffraction curve (111) has been elucidated.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Письма в журнал технической физики
- Vol. 47 (15)
Структурная характеризация короткопериодной сверхрешетки на основе гетероструктуры CdF-=SUB=-2-=/SUB=-/CaF-=SUB=-2-=/SUB=-/Si(111) методами просвечивающей электронной микроскопии и рентгеновской дифрактометрии
A detailed study of the structure of a short-period superlattice based on alternating layers of cadmium and calcium fluorides, grown by molecular beam epitaxy on a Si (111) substrate, by transmission electron microscopy and X-ray diffractometry, has been carried out. It was found that the superlattice is in a pseudomorphic state, and a lateral inhomogeneity with a fragment size of 10 - 40 nm was found. The reason for the broadening of the main and satellite peaks of the SL on the (111) diffraction curve has been clarified.
- 1 January 2021
- Published by Ioffe Institute Russian Academy of Sciences in Письма в журнал технической физики
- Vol. 47 (15)
Структурная характеризация короткопериодной сверхрешетки на основе гетероструктуры CdF-=SUB=-2-=/SUB=-/CaF-=SUB=-2-=/SUB=-/Si(111) методами просвечивающей электронной микроскопии и рентгеновской дифрактометрии
A detailed study of the structure of a short-period superlattice based on alternating layers of cadmium and calcium fluorides, grown by molecular beam epitaxy on a Si (111) substrate, by transmission electron microscopy and X-ray diffractometry, has been carried out. It was found that the superlattice is in a pseudomorphic state, and a lateral inhomogeneity with a fragment size of 10 - 40 nm was found. The reason for the broadening of the main and satellite peaks of the SL on the (111) diffraction curve has been clarified.
- 1 January 2020
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 90 (9) , 1449
Исследование структурных особенностей дентина методами микротомографии и просвечивающей электронной микроскопии
Dentin of human teeth is a natural composite material with a layered hierarchical structure; it is formed by micro- and nanostructures whose complex relations obey the laws not yet fully understood. In order to understand the effect of the dentin structure on its mechanical properties, a study of dentin samples prepared from human molars and subjected to a uniaxial compression was made. Synchrotron X-ray microtomography and transmission electron microscopy were employed to investigate the elements of dentin matrix and the tubules which cross the matrix. Single structural features based on the interaction of the elements, as well as the properties of the dentinal tubules, which can stop crack propagation have been investigated. A model is proposed for calculating the conditions of stopping of a mode II crack by generation of secondary cracks caused by the stresses over the surfaces of the tubules.
- 1 January 2020
- Published by Ioffe Institute Russian Academy of Sciences in Журнал технической физики
- Vol. 90 (9) , 1449
Исследование структурных особенностей дентина методами микротомографии и просвечивающей электронной микроскопии
Dentin of human teeth is a natural composite material with a layered hierarchical structure; it is formed by micro- and nanostructures whose complex relations obey the laws not yet fully understood. In order to understand the effect of the dentin structure on its mechanical properties, a study of dentin samples prepared from human molars and subjected to a uniaxial compression was made. Synchrotron X-ray microtomography and transmission electron microscopy were employed to investigate the elements of dentin matrix and the tubules which cross the matrix. Single structural features based on the interaction of the elements, as well as the properties of the dentinal tubules, which can stop crack propagation have been investigated. A model is proposed for calculating the conditions of stopping of a mode II crack by generation of secondary cracks caused by the stresses over the surfaces of the tubules.
- Open Access
Distribution of Dislocations near the Interface in AlN Crystals Grown on Evaporated SiC Substrates
To exploit unique properties of thin films of group III-nitride semiconductors, the production of native substrates is to be developed. The best choice would be AlN; however, presently available templates on sapphire or SiC substrates are defective. The quality of AlN could be improved by eliminating the substrate during the layer growth. In this paper, we demonstrate freestanding AlN layers fabricated by an SiC substrate evaporation method. Such layers were used to investigate dislocation structures near the former AlN–SiC interface. Specimens were characterized by synchrotron radiation imaging, triple-axis diffractometry and transmission electron microscopy (TEM). We found that the evaporation process under non-optimal conditions affected the dislocation structure. When the growth had been optimized, AlN layers showed a uniform distribution of dislocations. The dislocations tended to constitute low-angle subgrain boundaries, which produced out-of-plane and in-plane tilt angles of about 2–3 arc-min. Similar broadening was observed in both symmetric and asymmetric rocking curves, which proved the presence of edge, screws as well as mixed dislocation content. TEM revealed arrays of edge threading dislocations, but their predominance over the other threading dislocations was not supported by present study. To explain the experimental observations, a theoretical model of the dislocation structure formation is proposed.
Open AccessDistribution of Dislocations near the Interface in AlN Crystals Grown on Evaporated SiC Substrates
To exploit unique properties of thin films of group III-nitride semiconductors, the production of native substrates is to be developed. The best choice would be AlN; however, presently available templates on sapphire or SiC substrates are defective. The quality of AlN could be improved by eliminating the substrate during the layer growth. In this paper, we demonstrate freestanding AlN layers fabricated by an SiC substrate evaporation method. Such layers were used to investigate dislocation structures near the former AlN–SiC interface. Specimens were characterized by synchrotron radiation imaging, triple-axis diffractometry and transmission electron microscopy (TEM). We found that the evaporation process under non-optimal conditions affected the dislocation structure. When the growth had been optimized, AlN layers showed a uniform distribution of dislocations. The dislocations tended to constitute low-angle subgrain boundaries, which produced out-of-plane and in-plane tilt angles of about 2–3 arc-min. Similar broadening was observed in both symmetric and asymmetric rocking curves, which proved the presence of edge, screws as well as mixed dislocation content. TEM revealed arrays of edge threading dislocations, but their predominance over the other threading dislocations was not supported by present study. To explain the experimental observations, a theoretical model of the dislocation structure formation is proposed.
- 15 October 2015
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 30 (11) , 114002
TEM investigation of semipolar GaN layers grown on Si(001) offcut substrates
We present the results of a conventional and high-resolution electron microscopy investigation of thick (up to 15 μm) semipolar GaN layers grown on Si(001) offcut substrates with 3C-SiC and AlN buffer layers. GaN and AlN layers have been grown by chloride vapor phase epitaxy. The silicon carbide buffer layers were produced by a new method of solid-phase synthesis on 4 and 7° offcut Si(001) substrates. It is shown that the use of solid-phase synthesis for the formation of SiC layer allows one to grow a semipolar GaN layer. The asymmetrical defect structure of the semipolar layer is revealed.
- 15 October 2015
- Published by IOP Publishing in Semiconductor Science and Technology
- Vol. 30 (11) , 114002
TEM investigation of semipolar GaN layers grown on Si(001) offcut substrates
We present the results of a conventional and high-resolution electron microscopy investigation of thick (up to 15 μm) semipolar GaN layers grown on Si(001) offcut substrates with 3C-SiC and AlN buffer layers. GaN and AlN layers have been grown by chloride vapor phase epitaxy. The silicon carbide buffer layers were produced by a new method of solid-phase synthesis on 4 and 7° offcut Si(001) substrates. It is shown that the use of solid-phase synthesis for the formation of SiC layer allows one to grow a semipolar GaN layer. The asymmetrical defect structure of the semipolar layer is revealed.
- 1 April 2014
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 40 (4) , 296-299
Electron-microscopic study of Sn-chrisotile asbestos nanocomposite
Transmission electron microscopy was used to study the structural state of tin in Sn-chrisotile asbestos nanocomposite. It is shown that tin in the nanocomposite forms a system of nanowires, which, in turn, consist of crystallites of different lengths. Various orientational relations between the matrix and crystallites are revealed.
- 1 April 2014
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 40 (4) , 296-299
Electron-microscopic study of Sn-chrisotile asbestos nanocomposite
Transmission electron microscopy was used to study the structural state of tin in Sn-chrisotile asbestos nanocomposite. It is shown that tin in the nanocomposite forms a system of nanowires, which, in turn, consist of crystallites of different lengths. Various orientational relations between the matrix and crystallites are revealed.
- Open Access
- 29 November 2013
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 471 (1) , 012033
Transmission electron microscopy study of semi-polar gallium nitride layer grown by hydride-chloride vapour-phase epitaxy on SiC/(001)Si heterostructure
The structure of 10-μm-thick GaN layer grown by chloride vapour-phase epitaxy on 1.5-inch SiC/(001)Si templates has been investigated by transmission electron microscopy (TEM). The silicon carbide buffer layer has been fabricated by a new method of solid-phase synthesis. It was found that the GaN layer consists of oriented grains with size of tenths of a micron. The grains have wurtzite structure, and the {0001} GaN planes are oriented parallel to {111} Si, that is, the deviation of the axis c of GaN crystallite from the normal to the substrate is about 52°. The revealed epitaxial relationship between substrate and most grains is (023)GaN||(001)3C-Si||(001)Si and [20]GaN||[110]3C-SiC||[110]Si. Some inclusions of sphalerite gallium nitride were also found in the epilayer.
- 29 November 2013
- Published by IOP Publishing in Journal of Physics: Conference Series
- Vol. 471 (1) , 012033
Open AccessTransmission electron microscopy study of semi-polar gallium nitride layer grown by hydride-chloride vapour-phase epitaxy on SiC/(001)Si heterostructure
The structure of 10-μm-thick GaN layer grown by chloride vapour-phase epitaxy on 1.5-inch SiC/(001)Si templates has been investigated by transmission electron microscopy (TEM). The silicon carbide buffer layer has been fabricated by a new method of solid-phase synthesis. It was found that the GaN layer consists of oriented grains with size of tenths of a micron. The grains have wurtzite structure, and the {0001} GaN planes are oriented parallel to {111} Si, that is, the deviation of the axis c of GaN crystallite from the normal to the substrate is about 52°. The revealed epitaxial relationship between substrate and most grains is (023)GaN||(001)3C-Si||(001)Si and [20]GaN||[110]3C-SiC||[110]Si. Some inclusions of sphalerite gallium nitride were also found in the epilayer.
- 1 April 2011
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 37 (4) , 326-329
Structural characterization of GaN epilayers on silicon: Effect of buffer layers
Cross-sections of GaN/AlN/3C-SiC/Si(111) system have been studied by electron microscopy techniques. A nanometer thick buffer layer of silicon carbide on Si(111) substrate was formed using an original solid-phase epitaxy method. The subsequent layers of gallium nitride and aluminum nitride were grown by the method hydride-chloride vapor phase epitaxy. The resulting GaN layers display neither threading dislocations nor cracks on any scale. The main fraction of defects in GaN layers have the form of dislocation pileups that are localized at and oriented parallel to the GaN/AlN interface. The dislocation density in the obtained GaN layers is (1–2) × 109 cm−2, which corresponds to a minimum level reported in the available literature. The buffer AlN layer contains nanopores, which reduce the level of stresses at the GaN/AlN interface and thus almost completely inhibit the formation of threading dislocations.
- 1 April 2011
- Published by Pleiades Publishing Ltd in Technical Physics Letters
- Vol. 37 (4) , 326-329
Structural characterization of GaN epilayers on silicon: Effect of buffer layers
Cross-sections of GaN/AlN/3C-SiC/Si(111) system have been studied by electron microscopy techniques. A nanometer thick buffer layer of silicon carbide on Si(111) substrate was formed using an original solid-phase epitaxy method. The subsequent layers of gallium nitride and aluminum nitride were grown by the method hydride-chloride vapor phase epitaxy. The resulting GaN layers display neither threading dislocations nor cracks on any scale. The main fraction of defects in GaN layers have the form of dislocation pileups that are localized at and oriented parallel to the GaN/AlN interface. The dislocation density in the obtained GaN layers is (1–2) × 109 cm−2, which corresponds to a minimum level reported in the available literature. The buffer AlN layer contains nanopores, which reduce the level of stresses at the GaN/AlN interface and thus almost completely inhibit the formation of threading dislocations.