Giorgio De Simoni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Giorgio De Simoni has a total of 97 co-authors. Here are the top co-authors by number of shared publications:
- Francesco Giazotto
NEST, Istituto Nanoscienze-CNR and Scuola Normale Superiore
37 shared publications - Claudio Puglia
INFN Sezione di Pisa
11 shared publications - Alessandro Paghi
Dipartimento di Ingegneria dell’Informazione, Università di Pisa, Pisa, Italy
7 shared publications - Alessandro Braggio
NEST, Istituto Nanoscienze-CNR and Scuola Normale Superiore , I-56127 Pisa
6 shared publications - Sebastiano Battisti
Istituto Nanoscienze-CNR NEST Scuola Normale Superiore 56127 Pisa Italy
6 shared publications Claudio Puglia
NEST, Istituto Nanoscienze-CNR and Scuola Normale Superiore, Piazza San Silvestro 12, I-56127 Pisa, Italy
5 shared publications
Latest Publications
- 18 August 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (2) , 024047
Highly linear flux-to-voltage transducer based on superconducting quantum interference proximity transistors
Superconducting quantum interference devices (SQUIDs) are state-of-the-art in ultrasensitive magnetometry; however, conventional SQUIDs are fundamentally limited by the inherently nonlinear, periodic nature of their transfer function. Although flux-locked loop configurations can mitigate this issue, they introduce electronic complexity and bandwidth constraints that hinder scalability in quantum circuits. In this work, we present an experimental demonstration of the bi-SQUIPT, a flux transducer that modulates the density of states in a proximitized superconducting weak link. The device employs a dual-loop architecture with differential readout, which enables cancellation of nonlinearities typical of individual elements, achieving a voltage swing of approximately $120\text{ }\mathrm{\ensuremath{\mu}}\mathrm{V}$. Measurements yield a spurious-free dynamic range of up to 60 dB, consistent with theoretical predictions and comparable to that of SQUID arrays, while maintaining femtowatt power dissipation. The results further highlight a remarkable operational stability up to 600 mK, positioning the bi-SQUIPT as an enabling technology for high-density cryogenic quantum electronics.- 18 August 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 26 (2) , 024047
Highly linear flux-to-voltage transducer based on superconducting quantum interference proximity transistors
Superconducting quantum interference devices (SQUIDs) are state-of-the-art in ultrasensitive magnetometry; however, conventional SQUIDs are fundamentally limited by the inherently nonlinear, periodic nature of their transfer function. Although flux-locked loop configurations can mitigate this issue, they introduce electronic complexity and bandwidth constraints that hinder scalability in quantum circuits. In this work, we present an experimental demonstration of the bi-SQUIPT, a flux transducer that modulates the density of states in a proximitized superconducting weak link. The device employs a dual-loop architecture with differential readout, which enables cancellation of nonlinearities typical of individual elements, achieving a voltage swing of approximately $120\text{ }\mathrm{\ensuremath{\mu}}\mathrm{V}$. Measurements yield a spurious-free dynamic range of up to 60 dB, consistent with theoretical predictions and comparable to that of SQUID arrays, while maintaining femtowatt power dissipation. The results further highlight a remarkable operational stability up to 600 mK, positioning the bi-SQUIPT as an enabling technology for high-density cryogenic quantum electronics.- Open Access
- 7 May 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (5)
Highly linear proximity-based double-loop SQUID operating above 4 K
We demonstrate a highly linear superconducting quantum interference device (SQUID) interferometer based on a double-loop (Bi-SQUID) architecture incorporating three superconductor-normal metal-superconductor ( S - N - S ) junctions. Fabricated using niobium-gold technology, the device exhibits robust operation at liquid helium temperatures, with a superconducting transition temperature of 8.5 K. The dc flux-to-voltage transfer function demonstrates sharp, symmetric, and highly linear behavior at temperatures up to 5 K. Bi-SQUIDs featuring our single-element S - N - S design represent an interesting and original approach to this field, as they exhibit a numerically estimated spurious-free dynamic range linearity exceeding 60 dB, achieved in a single element, simplifying the requirements in terms of arrays containing hundreds of junctions. These results highlight the potential of proximity-based Bi-SQUIDs for compact and highly linear cryogenic interferometric devices, motivating future investigations of their dynamic and noise performance for applied implementations such as quantum sensing, magnetometry, and biomedical diagnostics.
- 7 May 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (5)
Open AccessHighly linear proximity-based double-loop SQUID operating above 4 K
We demonstrate a highly linear superconducting quantum interference device (SQUID) interferometer based on a double-loop (Bi-SQUID) architecture incorporating three superconductor-normal metal-superconductor ( S - N - S ) junctions. Fabricated using niobium-gold technology, the device exhibits robust operation at liquid helium temperatures, with a superconducting transition temperature of 8.5 K. The dc flux-to-voltage transfer function demonstrates sharp, symmetric, and highly linear behavior at temperatures up to 5 K. Bi-SQUIDs featuring our single-element S - N - S design represent an interesting and original approach to this field, as they exhibit a numerically estimated spurious-free dynamic range linearity exceeding 60 dB, achieved in a single element, simplifying the requirements in terms of arrays containing hundreds of junctions. These results highlight the potential of proximity-based Bi-SQUIDs for compact and highly linear cryogenic interferometric devices, motivating future investigations of their dynamic and noise performance for applied implementations such as quantum sensing, magnetometry, and biomedical diagnostics.
- 27 March 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (3)
Thermally modulated SINIS transconductance amplifier
- 27 March 2026
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 25 (3)
Thermally modulated SINIS transconductance amplifier
- 1 December 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (6)
Streamline-controlled rectification of supercurrent in thin-film asymmetric weak links
- 1 December 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (6)
Streamline-controlled rectification of supercurrent in thin-film asymmetric weak links
- Open Access
Highly-Linear Proximity-Based Bi-SQUID Operating above 4 K
We demonstrate a highly linear superconducting quantum interference device (SQUID) amplifier based on a double-loop (Bi-SQUID) architecture incorporating three superconductor-normal metal-superconductor (S-N-S) junctions. Fabricated using niobium-gold technology, the device exhibits robust operation at liquid helium temperatures, with a superconducting transition temperature of 8.5 K. The flux-to-voltage transfer function demonstrates sharp, symmetric, and highly linear behavior at temperatures up to 5 K. Bi-SQUIDs featuring our single-element S-N-S design represent an interesting and original approach to this field, as they demonstrate a numerically estimated spurious-free dynamic range (SFDR) linearity exceeding 60 dB, achieved in a single element, simplifying the requirements in terms of arrays containing hundreds of junctions. These results highlight the potential of proximity-based Bi-SQUIDs for compact, low-noise, and highly linear cryogenic amplifiers in quantum sensing, magnetometry, and biomedical diagnostics.
Open AccessHighly-Linear Proximity-Based Bi-SQUID Operating above 4 K
We demonstrate a highly linear superconducting quantum interference device (SQUID) amplifier based on a double-loop (Bi-SQUID) architecture incorporating three superconductor-normal metal-superconductor (S-N-S) junctions. Fabricated using niobium-gold technology, the device exhibits robust operation at liquid helium temperatures, with a superconducting transition temperature of 8.5 K. The flux-to-voltage transfer function demonstrates sharp, symmetric, and highly linear behavior at temperatures up to 5 K. Bi-SQUIDs featuring our single-element S-N-S design represent an interesting and original approach to this field, as they demonstrate a numerically estimated spurious-free dynamic range (SFDR) linearity exceeding 60 dB, achieved in a single element, simplifying the requirements in terms of arrays containing hundreds of junctions. These results highlight the potential of proximity-based Bi-SQUIDs for compact, low-noise, and highly linear cryogenic amplifiers in quantum sensing, magnetometry, and biomedical diagnostics.
- Open Access
- 26 September 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
Supercurrent time division multiplexing with solid-state integrated hybrid superconducting electronics
Time-division multiplexing of cryogenic signals is a promising approach to reduce space requirements, shorten cooldown times, and increase the number of quantum devices measured per cooldown. We demonstrate time-division multiplexing of non-dissipative supercurrents using voltage-controlled hybrid superconducting demultiplexers. These chips integrate superconducting Josephson Field Effect Transistors including Al superconducting electrodes, proximitized semiconducting InAs channels, and hafnium oxide gate insulators. Each transistor fully suppresses the switching current and increases the resistance 20 times under a gate voltage of −4.5 V. A demultiplexer with one input and eight outputs showed a non-dissipative input range of ±2 μA, operating up to 100 MHz in signal frequency, and 100 kHz in switching frequency at 50 mK. It achieved near-zero insertion loss in the superconducting state and an \(\frac{{ON}}{{OFF}}\) ratio of 17.5 dB. By optimizing the signal layout, the operation was extended up to 4 GHz using a demultiplexer with two outputs.- 26 September 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-12
Open AccessSupercurrent time division multiplexing with solid-state integrated hybrid superconducting electronics
Time-division multiplexing of cryogenic signals is a promising approach to reduce space requirements, shorten cooldown times, and increase the number of quantum devices measured per cooldown. We demonstrate time-division multiplexing of non-dissipative supercurrents using voltage-controlled hybrid superconducting demultiplexers. These chips integrate superconducting Josephson Field Effect Transistors including Al superconducting electrodes, proximitized semiconducting InAs channels, and hafnium oxide gate insulators. Each transistor fully suppresses the switching current and increases the resistance 20 times under a gate voltage of −4.5 V. A demultiplexer with one input and eight outputs showed a non-dissipative input range of ±2 μA, operating up to 100 MHz in signal frequency, and 100 kHz in switching frequency at 50 mK. It achieved near-zero insertion loss in the superconducting state and an \(\frac{{ON}}{{OFF}}\) ratio of 17.5 dB. By optimizing the signal layout, the operation was extended up to 4 GHz using a demultiplexer with two outputs. - Open Access
- 30 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (26)
Photonic negative differential thermal conductance enabled by NIS junctions
Due to their sensitivity to temperature variations, normal metal–insulator–superconductor (NIS) junctions are utilized in various thermal devices. This study illustrates that two NISIN reservoirs can achieve a measurable negative differential thermal conductance (NDTC). This phenomenon is enabled by photon-mediated heat exchange, which is profoundly affected by the temperature-dependent impedance matching between the reservoirs. Under suitable configurations, the heat current is suppressed for increasingly large temperature gradients, resulting in NDTC. We also propose experimental configurations that allow for the unambiguous discrimination of this effect. We employ superconducting aluminum in conjunction with either silver or epitaxial InAs to facilitate the experimental observation of NDTC at low temperatures over significant sub-Kelvin ranges. This advances the development of devices that exploit NDTC to enhance the regulation of heat and temperature in cryogenic environments, such as thermal switches, transistors, and amplifiers.
- 30 June 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (26)
Open AccessPhotonic negative differential thermal conductance enabled by NIS junctions
Due to their sensitivity to temperature variations, normal metal–insulator–superconductor (NIS) junctions are utilized in various thermal devices. This study illustrates that two NISIN reservoirs can achieve a measurable negative differential thermal conductance (NDTC). This phenomenon is enabled by photon-mediated heat exchange, which is profoundly affected by the temperature-dependent impedance matching between the reservoirs. Under suitable configurations, the heat current is suppressed for increasingly large temperature gradients, resulting in NDTC. We also propose experimental configurations that allow for the unambiguous discrimination of this effect. We employ superconducting aluminum in conjunction with either silver or epitaxial InAs to facilitate the experimental observation of NDTC at low temperatures over significant sub-Kelvin ranges. This advances the development of devices that exploit NDTC to enhance the regulation of heat and temperature in cryogenic environments, such as thermal switches, transistors, and amplifiers.
- 10 June 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (1)
Photonic heat amplifiers based on a disordered semiconductor
- 10 June 2025
- Published by American Physical Society (APS) in Physical Review Applied
- Vol. 24 (1)
Photonic heat amplifiers based on a disordered semiconductor
- Open Access
- 28 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (4)
Cryogenic behavior of high-permittivity gate dielectrics: The impact of atomic layer deposition temperature and the lithographic patterning method
Dielectrics featuring a high relative permittivity, i.e., high-k dielectrics, have become the standard insulators in gate architectures, enhancing the electrical performance of both room temperature and cryogenic electronics. This study delves into the cryogenic (3 K) performance of high-k dielectrics commonly used as gate insulators. We fabricated Al2O3 and HfO2 layers via atomic layer deposition (ALD) and extrapolated relative permittivity (k) and dielectric strength (EBD) from AC (100 Hz–100 kHz) and DC measurements on metal–insulator–metal capacitors. Our findings reveal a strong dependence of HfO2 cryogenic performance on ALD growth temperature, while the latter shows a negligible impact on Al2O3. We estimated ∼9% and ∼14% reductions in the relative permittivities of HfO2 and Al2O3, respectively, at temperatures from 300 to 3 K. Additionally, we designed and fabricated Al2O3/HfO2 bilayers and checked their properties at cryogenic temperatures. The study also investigates the impact of the patterning method, namely, UV or electron-beam lithography (acceleration voltage of 10, 20, or 30 kV), on the high-k dielectric properties.
- 28 January 2025
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 137 (4)
Open AccessCryogenic behavior of high-permittivity gate dielectrics: The impact of atomic layer deposition temperature and the lithographic patterning method
Dielectrics featuring a high relative permittivity, i.e., high-k dielectrics, have become the standard insulators in gate architectures, enhancing the electrical performance of both room temperature and cryogenic electronics. This study delves into the cryogenic (3 K) performance of high-k dielectrics commonly used as gate insulators. We fabricated Al2O3 and HfO2 layers via atomic layer deposition (ALD) and extrapolated relative permittivity (k) and dielectric strength (EBD) from AC (100 Hz–100 kHz) and DC measurements on metal–insulator–metal capacitors. Our findings reveal a strong dependence of HfO2 cryogenic performance on ALD growth temperature, while the latter shows a negligible impact on Al2O3. We estimated ∼9% and ∼14% reductions in the relative permittivities of HfO2 and Al2O3, respectively, at temperatures from 300 to 3 K. Additionally, we designed and fabricated Al2O3/HfO2 bilayers and checked their properties at cryogenic temperatures. The study also investigates the impact of the patterning method, namely, UV or electron-beam lithography (acceleration voltage of 10, 20, or 30 kV), on the high-k dielectric properties.
- 13 January 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (2)
Publisher's Note: “Extremely weak sub-kelvin electron–phonon coupling in InAs on Insulator” [Appl. Phys. Lett. 125, 202601 (2024)]
- 13 January 2025
- Published by AIP Publishing in Applied Physics Letters
- Vol. 126 (2)
Publisher's Note: “Extremely weak sub-kelvin electron–phonon coupling in InAs on Insulator” [Appl. Phys. Lett. 125, 202601 (2024)]