Yanbing Ni
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Yanbing Ni has a total of 16 co-authors. Here are the top co-authors by number of shared publications:
- Haitao Liu
Ministry of Education, Tianjin University
3 shared publications - Tian Huang
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin, China
3 shared publications - Juliang Xiao
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin, China
2 shared publications - Shaofei Meng
Key Laboratory of Mechanism Theory and Equipment Design of Ministry of Education, Tianjin University, Tianjin, China
2 shared publications - Biao Zhang
Tianjin University
1 shared publication - Hu Shi
Xi’an Jiaotong University
1 shared publication
Latest Publications
- 2 May 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (11-12) , 5353-5369
An inversion method for identifying the convection heat transfer coefficients of friction stir welding using a surrogate model
- 2 May 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 126 (11-12) , 5353-5369
An inversion method for identifying the convection heat transfer coefficients of friction stir welding using a surrogate model
- 25 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (5-6) , 3747-3758
A method for process parameter optimization of simultaneous double-sided friction stir welding using a heat transfer model
- 25 June 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 121 (5-6) , 3747-3758
A method for process parameter optimization of simultaneous double-sided friction stir welding using a heat transfer model
- 30 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (3) , 959-968
Modified Robust Dynamic Control for a Diamond Parallel Robot
In this paper, a modified robust dynamic control (MRDC) method is proposed for a 2-DOF Diamond parallel robot to realize high-precision and high-speed cooperating motion. Diamond robot is a double-input and double-output system with both coupled dynamics and uncertain dynamics. Based on the dynamic equation in joint coordinates, a MRDC that can drive the two active arms of Diamond robot to stay in two decoupled terminal sliding modes with continuous control signals is designed. The control law of MRDC is specially constructed to be insensitive to the noise in speed signal, which can help to improve error convergence speed without causing undesirable system chattering. With suitable control parameters, the proposed MRDC can assure the stability of Diamond robot even in the presence of disturbance, parameter variation, etc., which is verified in sense of Lyapunov. MRDC is then successfully implemented on a Diamond robot prototype controlled by a commercial PMAC motion control card. Experimental results show that proposed MRDC can achieve both good trajectory tracking performance and good robustness against disturbance. Compared with the robust dynamic control and PD control, MRDC can avoid undesirable system chattering and assure better trajectory tracking accuracy respectively.
- 30 April 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE/ASME Transactions on Mechatronics
- Vol. 24 (3) , 959-968
Modified Robust Dynamic Control for a Diamond Parallel Robot
In this paper, a modified robust dynamic control (MRDC) method is proposed for a 2-DOF Diamond parallel robot to realize high-precision and high-speed cooperating motion. Diamond robot is a double-input and double-output system with both coupled dynamics and uncertain dynamics. Based on the dynamic equation in joint coordinates, a MRDC that can drive the two active arms of Diamond robot to stay in two decoupled terminal sliding modes with continuous control signals is designed. The control law of MRDC is specially constructed to be insensitive to the noise in speed signal, which can help to improve error convergence speed without causing undesirable system chattering. With suitable control parameters, the proposed MRDC can assure the stability of Diamond robot even in the presence of disturbance, parameter variation, etc., which is verified in sense of Lyapunov. MRDC is then successfully implemented on a Diamond robot prototype controlled by a commercial PMAC motion control card. Experimental results show that proposed MRDC can achieve both good trajectory tracking performance and good robustness against disturbance. Compared with the robust dynamic control and PD control, MRDC can avoid undesirable system chattering and assure better trajectory tracking accuracy respectively.
- 19 July 2015
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 28 (4) , 830-840
Dimensional synthesis of a 3-DOF parallel manipulator with full circle rotation
Parallel robots are widely used in the academic and industrial fields. In spite of the numerous achievements in the design and dimensional synthesis of the low-mobility parallel robots, few research efforts are directed towards the asymmetric 3-DOF parallel robots whose end-effector can realize 2 translational and 1 rotational(2T1R) motion. In order to develop a manipulator with the capability of full circle rotation to enlarge the workspace, a new 2T1R parallel mechanism is proposed. The modeling approach and kinematic analysis of this proposed mechanism are investigated. Using the method of vector analysis, the inverse kinematic equations are established. This is followed by a vigorous proof that this mechanism attains an annular workspace through its circular rotation and 2 dimensional translations. Taking the first order perturbation of the kinematic equations, the error Jacobian matrix which represents the mapping relationship between the error sources of geometric parameters and the end-effector position errors is derived. With consideration of the constraint conditions of pressure angles and feasible workspace, the dimensional synthesis is conducted with a goal to minimize the global comprehensive performance index. The dimension parameters making the mechanism to have optimal error mapping and kinematic performance are obtained through the optimization algorithm. All these research achievements lay the foundation for the prototype building of such kind of parallel robots.
- 19 July 2015
- Published by Elsevier in Chinese Journal of Mechanical Engineering
- Vol. 28 (4) , 830-840
Dimensional synthesis of a 3-DOF parallel manipulator with full circle rotation
Parallel robots are widely used in the academic and industrial fields. In spite of the numerous achievements in the design and dimensional synthesis of the low-mobility parallel robots, few research efforts are directed towards the asymmetric 3-DOF parallel robots whose end-effector can realize 2 translational and 1 rotational(2T1R) motion. In order to develop a manipulator with the capability of full circle rotation to enlarge the workspace, a new 2T1R parallel mechanism is proposed. The modeling approach and kinematic analysis of this proposed mechanism are investigated. Using the method of vector analysis, the inverse kinematic equations are established. This is followed by a vigorous proof that this mechanism attains an annular workspace through its circular rotation and 2 dimensional translations. Taking the first order perturbation of the kinematic equations, the error Jacobian matrix which represents the mapping relationship between the error sources of geometric parameters and the end-effector position errors is derived. With consideration of the constraint conditions of pressure angles and feasible workspace, the dimensional synthesis is conducted with a goal to minimize the global comprehensive performance index. The dimension parameters making the mechanism to have optimal error mapping and kinematic performance are obtained through the optimization algorithm. All these research achievements lay the foundation for the prototype building of such kind of parallel robots.
- 13 December 2013
- Published by Springer Nature in Transactions of Tianjin University
- Vol. 19 (6) , 440-447
Error analysis of assembly linkage of transport jig for large aircraft parts
- 13 December 2013
- Published by Springer Nature in Transactions of Tianjin University
- Vol. 19 (6) , 440-447
Error analysis of assembly linkage of transport jig for large aircraft parts