Chae-Hyoung Kim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Chae-Hyoung Kim has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
Jin-Han Kim
2 shared publicationsJungho Lee
2 shared publicationsKwang-Jin Lee
2 shared publicationsNamkyung Cho
2 shared publications- Seongphil Woo
Korea Aerospace Research Institute, Daejeon 34133, Republic of Korea
2 shared publications Younseok So
2 shared publications
Latest Publications
- Open Access
- 31 May 2026
- Published by The Korean Society of Propulsion Engineers in Journal of Propulsion and Energy
- Vol. 6 (1) , 68-86
Numerical Study of Supersonic Retro-Propulsion Flow Characteristics based on Low-Altitude Descending Flight Mach Numbers
- 31 May 2026
- Published by The Korean Society of Propulsion Engineers in Journal of Propulsion and Energy
- Vol. 6 (1) , 68-86
Open AccessNumerical Study of Supersonic Retro-Propulsion Flow Characteristics based on Low-Altitude Descending Flight Mach Numbers
- Open Access
Numerical Analysis of Ejector Flow Performance for High-Altitude Simulation
In this study we perform a computational numerical analysis to examine the flow characteristics of a system composed of a rocket engine, supersonic diffuser, and ejector system. When the nozzle expansion ratio of a rocket engine increases, it is necessary to maintain high-vacuum conditions during ground hot testing, which requires a supersonic diffuser and ejector system. The integrated model, consisting of multiple systems and a single-ejector system model, exhibits a difference in the initial volume to be evacuated. Although some differences are observed during the initial vacuum transition process, both models maintain the same final vacuum pressure (4 kPa). During the initial vacuum process, if the injection pressure of the ejector decreases below the design pressure, vacuum degradation occurs because of momentum deficiency, followed by pressure perturbations as the vacuum process resumes. Once the rocket engine ignites and flow is supplied to the suction region, two flow regions exist around the ejector nozzle exit. As these flows mix and move downstream, flow separation occurs in the expansion region. When the injection pressure of the ejector falls below the design pressure, the flow separation region moves forward, and this shift helps maintain the designed vacuum suction conditions.
Open AccessNumerical Analysis of Ejector Flow Performance for High-Altitude Simulation
In this study we perform a computational numerical analysis to examine the flow characteristics of a system composed of a rocket engine, supersonic diffuser, and ejector system. When the nozzle expansion ratio of a rocket engine increases, it is necessary to maintain high-vacuum conditions during ground hot testing, which requires a supersonic diffuser and ejector system. The integrated model, consisting of multiple systems and a single-ejector system model, exhibits a difference in the initial volume to be evacuated. Although some differences are observed during the initial vacuum transition process, both models maintain the same final vacuum pressure (4 kPa). During the initial vacuum process, if the injection pressure of the ejector decreases below the design pressure, vacuum degradation occurs because of momentum deficiency, followed by pressure perturbations as the vacuum process resumes. Once the rocket engine ignites and flow is supplied to the suction region, two flow regions exist around the ejector nozzle exit. As these flows mix and move downstream, flow separation occurs in the expansion region. When the injection pressure of the ejector falls below the design pressure, the flow separation region moves forward, and this shift helps maintain the designed vacuum suction conditions.
- Open Access
- 1 August 2019
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 23 (4)
Development Status of Technology Demonstration Model for Staged Combustion Cycle Engine
- 1 August 2019
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 23 (4)
Open AccessDevelopment Status of Technology Demonstration Model for Staged Combustion Cycle Engine
- Open Access
Forced Combustion Characteristics Related to Different Injection Locations in Unheated Supersonic Flow
This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen-air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen-air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.
Open AccessForced Combustion Characteristics Related to Different Injection Locations in Unheated Supersonic Flow
This work focuses on forced combustion with regards to the relationship between vent mixer models and several injection locations in unheated supersonic flow. A plasma jet torch was used to ignite the hydrogen-air mixture in a laboratory-scaled combustor duct. The flow field of the combustion was visualized with pressure and gas-sampling measurements. The vent mixers indicate good dispersion characteristics of the mixture for both parallel and normal 1 injections. However, forced combustion is dominantly governed by the injection rate toward the plasma jet (hot source) because the combustible region is restricted under the cold main flow. For this reason, the parallel injection, which provides the hydrogen-air mixture directly toward the plasma jet, shows good combustion performance. The normal 1 injection interacted with the vent mixers and shows slightly good combustion performance. Lastly, the normal 2 injection is little affected by the vent mixers and has poor combustion performance.
- Open Access
- 1 June 2018
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 22 (3)
Development Trend of Korean Staged Combustion Cycle Rocket Engine
- 1 June 2018
- Published by The Korean Society of Propulsion Engineers in Journal of the Korean Society of Propulsion Engineers
- Vol. 22 (3)
Open AccessDevelopment Trend of Korean Staged Combustion Cycle Rocket Engine