Nils Bartels
Research Subjects
Nils Bartels has a total of 36 co-authors. Here are the top co-authors by number of shared publications:
Wolfgang Riede
8 shared publications- Thomas Dekorsy
German Aerospace Center, Institute of Technical Physics, Stuttgart, Germany
4 shared publications Daniel Hampf
DiGOS Potsdam GmbH
2 shared publications- Denise Keil
Institute of Technical Physics, German Aerospace Center, Stuttgart, Germany
2 shared publications - Maciej Sznajder
German Aerospace Center Institute of Space Systems Robert-Hooke-Str. 7 28359 Bremen Germany
2 shared publications Moritz Vogel
German Aerosp Ctr DLR, Inst Tech Phys, Stuttgart, Germany
2 shared publications
Latest Publications
- Open Access
- 23 October 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (31) , 9332-9346
Retroreflectors for space traffic management
Satellite laser ranging (SLR) is a mature technology for precise orbit determination of satellites equipped with retroreflectors. While SLR has a long history in space geodesy, precise orbits of satellites are also very important to calculate collision probabilities of satellites. Hence, an increasing number of satellites are getting equipped with retroreflectors for this purpose. This work presents a retroreflector design specifically dedicated to space traffic management (STM). To support widespread adoption, the focus is on modularity, compactness, standardized interfaces, and integration of additional STM-relevant functions. This highly modular design also allows the accommodation of additional polarization optics for polarimetric SLR in order to identify specific satellites in space. We address key steps toward in-orbit demonstration, including prototype manufacturing, characterization, and space qualification. Furthermore, we analyze the effects of manufacturing errors and thermal effects on the polarization properties of the retroreflector designs.
- 23 October 2025
- Published by Optica Publishing Group in Applied Optics
- Vol. 64 (31) , 9332-9346
Open AccessRetroreflectors for space traffic management
Satellite laser ranging (SLR) is a mature technology for precise orbit determination of satellites equipped with retroreflectors. While SLR has a long history in space geodesy, precise orbits of satellites are also very important to calculate collision probabilities of satellites. Hence, an increasing number of satellites are getting equipped with retroreflectors for this purpose. This work presents a retroreflector design specifically dedicated to space traffic management (STM). To support widespread adoption, the focus is on modularity, compactness, standardized interfaces, and integration of additional STM-relevant functions. This highly modular design also allows the accommodation of additional polarization optics for polarimetric SLR in order to identify specific satellites in space. We address key steps toward in-orbit demonstration, including prototype manufacturing, characterization, and space qualification. Furthermore, we analyze the effects of manufacturing errors and thermal effects on the polarization properties of the retroreflector designs.
- 13 August 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (24) , 6336-6344
Algorithm for detecting airborne objects with a thermal infrared camera to ensure a safe operation of laser-optical ground stations
Laser-optical ground stations play an important role for satellite laser communication and satellite laser ranging (SLR). The safe operation of lasers in public airspace, which usually requires approval by legal entities, requires reliable, redundant, and independent systems for airborne object detection to avoid a potentially hazardous laser exposition. In this work, we propose an algorithm based on classical image filtering and thresholding to detect aircraft in images taken with a thermal infrared camera. The algorithm is optimized and evaluated with an image dataset acquired by the infrared camera mounted to SLR station miniSLR located in Stuttgart, Germany. Despite its simplicity and efficiency (7 ms for an image with 640×512 pixels on a standard consumer PCU), we find that the proposed algorithm has a high accuracy, yielding a 99.8% correct classification of images. Although laser safety systems require several independent aircraft detection methods, the proposed algorithm might be a valuable contribution for companies and institutes with the need to operate lasers in public airspace.
- 13 August 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (24) , 6336-6344
Algorithm for detecting airborne objects with a thermal infrared camera to ensure a safe operation of laser-optical ground stations
Laser-optical ground stations play an important role for satellite laser communication and satellite laser ranging (SLR). The safe operation of lasers in public airspace, which usually requires approval by legal entities, requires reliable, redundant, and independent systems for airborne object detection to avoid a potentially hazardous laser exposition. In this work, we propose an algorithm based on classical image filtering and thresholding to detect aircraft in images taken with a thermal infrared camera. The algorithm is optimized and evaluated with an image dataset acquired by the infrared camera mounted to SLR station miniSLR located in Stuttgart, Germany. Despite its simplicity and efficiency (7 ms for an image with 640×512 pixels on a standard consumer PCU), we find that the proposed algorithm has a high accuracy, yielding a 99.8% correct classification of images. Although laser safety systems require several independent aircraft detection methods, the proposed algorithm might be a valuable contribution for companies and institutes with the need to operate lasers in public airspace.
- Open Access
- 17 June 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (18) , 4964-4973
Method for improving the positional accuracy in passive optical detection of space objects
The number of space objects, i.e., active satellites as well as space debris, is growing at an exponential rate. The management of congested space requires networks of sensors to detect and precisely measure the positions of objects in space. We describe a method that improves the positional accuracy of passive optical detection of space objects. The method is based on a laboratory sensor calibration, which is suitable for all types of cameras (CCD and CMOS cameras) and can easily be implemented for existing staring or tracking stations or even used with space-based passive optical sensors. The successful implementation of the method is demonstrated in a test campaign by measuring tracklets of several Earth-orbiting satellites with a ground-based staring system known as APPARILLO. In addition to its use in space object detection, we encourage that the presented method might also inspire other fields of research and technology, where images need to be acquired with precise timing.
- 17 June 2024
- Published by Optica Publishing Group in Applied Optics
- Vol. 63 (18) , 4964-4973
Open AccessMethod for improving the positional accuracy in passive optical detection of space objects
The number of space objects, i.e., active satellites as well as space debris, is growing at an exponential rate. The management of congested space requires networks of sensors to detect and precisely measure the positions of objects in space. We describe a method that improves the positional accuracy of passive optical detection of space objects. The method is based on a laboratory sensor calibration, which is suitable for all types of cameras (CCD and CMOS cameras) and can easily be implemented for existing staring or tracking stations or even used with space-based passive optical sensors. The successful implementation of the method is demonstrated in a test campaign by measuring tracklets of several Earth-orbiting satellites with a ground-based staring system known as APPARILLO. In addition to its use in space object detection, we encourage that the presented method might also inspire other fields of research and technology, where images need to be acquired with precise timing.
- Open Access
- 29 November 2023
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 13 (12) , 3653-3666
Effects of high-power laser radiation on polymers for 3D printing micro-optics
3D printing has become a widely used technique for manufacturing micro-optical components for sensing, measurements, biomedical and quantum technologies. Hence, knowing the maximum usable power or damage thresholds of 3D-printed micro-optics becomes crucial. Here we present a first study of the damage threshold values of the IP-S photoresist under high-power cw-, fs-, and ns-pulsed laser radiation with wavelengths in the NIR range. We also study the differences between visual evaluation using bright-field microscopy, DIC-microscopy, and beam-profile damage detection. Finally, we present several application-inspired use cases of 3D printed fiber micro-optics, reaching 10.5 W output power of cw-radiation at 915 nm and 4.5 W and 550 fs pulsed operation at 1040 nm.
- 29 November 2023
- Published by Optica Publishing Group in Optical Materials Express
- Vol. 13 (12) , 3653-3666
Open AccessEffects of high-power laser radiation on polymers for 3D printing micro-optics
3D printing has become a widely used technique for manufacturing micro-optical components for sensing, measurements, biomedical and quantum technologies. Hence, knowing the maximum usable power or damage thresholds of 3D-printed micro-optics becomes crucial. Here we present a first study of the damage threshold values of the IP-S photoresist under high-power cw-, fs-, and ns-pulsed laser radiation with wavelengths in the NIR range. We also study the differences between visual evaluation using bright-field microscopy, DIC-microscopy, and beam-profile damage detection. Finally, we present several application-inspired use cases of 3D printed fiber micro-optics, reaching 10.5 W output power of cw-radiation at 915 nm and 4.5 W and 550 fs pulsed operation at 1040 nm.
- Open Access
- 16 November 2023
- Published by Springer Nature in The Journal of the Astronautical Sciences
- Vol. 70 (6) , 1-21
Spacecraft Materials’ Reflectivity and Surface Morphology: Aging Caused by Proton Irradiation
The radiation environment in Low Earth Orbit (LEO) is dominated by protons captured by Earth’s magnetic field in the Inner Van-Allen belt. Defunct satellites and other space debris objects can be resident in this environment for several decades and even centuries. So far, there is little knowledge about the impact of long-duration proton exposure to the surface morphology and reflectivity in LEO environment. We report on a laboratory test campaign exposing typical spacecraft materials with protons of 100 keV and 2.5 keV kinetic energy and a fluence corresponding to an in-orbit duration of 100 years and 120 years, respectively, in an 800 km sun-synchronous orbit. Although we find microscopic changes in surface morphology, reflectivity changes of all tested materials were smaller than 15%. This result brings positive news for on-going efforts to use optical methods, e.g. lightcurve measurements or active polarimetry, for characterizing space objects, since it suggests that data can - to a good approximation - be analyzed without accounting for proton induced aging effects that might affect the materials’ optical properties over time.
- 16 November 2023
- Published by Springer Nature in The Journal of the Astronautical Sciences
- Vol. 70 (6) , 1-21
Open AccessSpacecraft Materials’ Reflectivity and Surface Morphology: Aging Caused by Proton Irradiation
The radiation environment in Low Earth Orbit (LEO) is dominated by protons captured by Earth’s magnetic field in the Inner Van-Allen belt. Defunct satellites and other space debris objects can be resident in this environment for several decades and even centuries. So far, there is little knowledge about the impact of long-duration proton exposure to the surface morphology and reflectivity in LEO environment. We report on a laboratory test campaign exposing typical spacecraft materials with protons of 100 keV and 2.5 keV kinetic energy and a fluence corresponding to an in-orbit duration of 100 years and 120 years, respectively, in an 800 km sun-synchronous orbit. Although we find microscopic changes in surface morphology, reflectivity changes of all tested materials were smaller than 15%. This result brings positive news for on-going efforts to use optical methods, e.g. lightcurve measurements or active polarimetry, for characterizing space objects, since it suggests that data can - to a good approximation - be analyzed without accounting for proton induced aging effects that might affect the materials’ optical properties over time.
- 7 September 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (26) , 7091-7103
Laser-induced molecular contamination de-risking activity for the Laser Interferometer Space Antenna
The Laser Interferometer Space Antenna (LISA) will be the first space-based gravitational wave observatory. LISA uses continuous-wave, infrared laser beams propagating among three widely separated spacecrafts to measure their distances with picometer accuracy via time-delay interferometry. These measurements put very high demands on the laser wavefront and are thus very sensitive to any deposits on laser optics that could be induced by laser-induced molecular contamination (LIMC). In this work, we describe the results of an extensive experimental test campaign assessing LIMC related risks for LISA. We find that the LIMC concern for LISA, even considering the high demands on the laser wavefront, may be greatly reduced compared to that observed at shorter wavelengths or with pulsed laser radiation. This result is very promising for LISA as well as for other space missions using continuous-wave, infrared laser radiation, e.g., in free space laser communication or quantum key distribution.
- 7 September 2023
- Published by Optica Publishing Group in Applied Optics
- Vol. 62 (26) , 7091-7103
Laser-induced molecular contamination de-risking activity for the Laser Interferometer Space Antenna
The Laser Interferometer Space Antenna (LISA) will be the first space-based gravitational wave observatory. LISA uses continuous-wave, infrared laser beams propagating among three widely separated spacecrafts to measure their distances with picometer accuracy via time-delay interferometry. These measurements put very high demands on the laser wavefront and are thus very sensitive to any deposits on laser optics that could be induced by laser-induced molecular contamination (LIMC). In this work, we describe the results of an extensive experimental test campaign assessing LIMC related risks for LISA. We find that the LIMC concern for LISA, even considering the high demands on the laser wavefront, may be greatly reduced compared to that observed at shorter wavelengths or with pulsed laser radiation. This result is very promising for LISA as well as for other space missions using continuous-wave, infrared laser radiation, e.g., in free space laser communication or quantum key distribution.
- Open Access
- 26 May 2022
- Published by Springer Nature in Communications Engineering
- Vol. 1 (1) , 1-10
Space object identification via polarimetric satellite laser ranging
Low Earth orbits are becoming congested. The rapid identification and precise orbit determination of space objects is mandatory for space management. Satellite laser ranging (SLR) enables precise orbit determination by measuring the two-way photon travel time of laser pulses from a ground station to satellites equipped with retroreflectors. Here we propose polarization-modulated SLR, where specially designed retroreflectors positioned on a satellite switch the polarization state of received polarized photons and reflect them back to a ground station for analysis. Satellite identifiers can be coded into arrays of reflectors with different polarizing properties, while the orbit determining capability of conventional SLR is maintained. We design, build and test polarized light-switching retroreflector assemblies and investigate the feasibility of accurate signal measurement from SLR ground stations. The approach is passive, straightforward to integrate and requires no electricity. Polarization-modulated SLR could contribute to increasing demands of space object monitoring, for example of mega-constellations or during cluster launches.
- 26 May 2022
- Published by Springer Nature in Communications Engineering
- Vol. 1 (1) , 1-10
Open AccessSpace object identification via polarimetric satellite laser ranging
Low Earth orbits are becoming congested. The rapid identification and precise orbit determination of space objects is mandatory for space management. Satellite laser ranging (SLR) enables precise orbit determination by measuring the two-way photon travel time of laser pulses from a ground station to satellites equipped with retroreflectors. Here we propose polarization-modulated SLR, where specially designed retroreflectors positioned on a satellite switch the polarization state of received polarized photons and reflect them back to a ground station for analysis. Satellite identifiers can be coded into arrays of reflectors with different polarizing properties, while the orbit determining capability of conventional SLR is maintained. We design, build and test polarized light-switching retroreflector assemblies and investigate the feasibility of accurate signal measurement from SLR ground stations. The approach is passive, straightforward to integrate and requires no electricity. Polarization-modulated SLR could contribute to increasing demands of space object monitoring, for example of mega-constellations or during cluster launches.
- Open Access
- 17 August 2021
- Published by Springer Nature in The Journal of the Astronautical Sciences
- Vol. 68 (4) , 1170-1185
Surface Modification of Space Exposed Materials Induced by Low Energetic Proton Irradiation
The aim of this paper is to verify if commonly occurring space debris materials change their reflectivity and morphology after being exposed to low energy protons. Therefore, a set of six different materials frequently used in spacecraft engineering was irradiated with low energy (100 keV) protons to simulate the aging of their surfaces due to space radiation in low Earth orbit (LEO). A microscopic and spectroscopic analysis of the irradiated samples reveals that the tested materials containing organic polymers (Polytetrafluoroethylene (PTFE) and carbon fiber reinforced plastic (CFRP)) show changes in surface morphology. Metallic surfaces did not show surface modifications but we found changes in the reflectivity of coated polyimide sheets, like used in Multi Layer Insulation blankets, during and after proton irradiation. Our results show that space materials exhibit significant changes after irradiation equivalent to the dose accumulated after 100 years in LEO. This knowledge is highly relevant for the interpretation of optical data related to the observation of space debris as well as to studies about laser-matter interaction for laser-based debris removal.
- 17 August 2021
- Published by Springer Nature in The Journal of the Astronautical Sciences
- Vol. 68 (4) , 1170-1185
Open AccessSurface Modification of Space Exposed Materials Induced by Low Energetic Proton Irradiation
The aim of this paper is to verify if commonly occurring space debris materials change their reflectivity and morphology after being exposed to low energy protons. Therefore, a set of six different materials frequently used in spacecraft engineering was irradiated with low energy (100 keV) protons to simulate the aging of their surfaces due to space radiation in low Earth orbit (LEO). A microscopic and spectroscopic analysis of the irradiated samples reveals that the tested materials containing organic polymers (Polytetrafluoroethylene (PTFE) and carbon fiber reinforced plastic (CFRP)) show changes in surface morphology. Metallic surfaces did not show surface modifications but we found changes in the reflectivity of coated polyimide sheets, like used in Multi Layer Insulation blankets, during and after proton irradiation. Our results show that space materials exhibit significant changes after irradiation equivalent to the dose accumulated after 100 years in LEO. This knowledge is highly relevant for the interpretation of optical data related to the observation of space debris as well as to studies about laser-matter interaction for laser-based debris removal.
- Open Access
- 21 June 2019
- Published by Springer Nature in CEAS Space Journal
- Vol. 11 (4) , 391-403
Design and qualification of a recessed satellite cornercube retroreflector for ground-based attitude verification via satellite laser ranging
- 21 June 2019
- Published by Springer Nature in CEAS Space Journal
- Vol. 11 (4) , 391-403
Open AccessDesign and qualification of a recessed satellite cornercube retroreflector for ground-based attitude verification via satellite laser ranging