Andreia Cristina Fonseca Alves
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Andreia Cristina Fonseca Alves has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Romario Victor Pacheco Antero
Universidade de Brasília
3 shared publications Satu Anneli Ojala
3 shared publicationsSergio Botelho de Oliveira
3 shared publications- Artur Jesus Motheo
São Carlos Institute of Chemistry, University of São Paulo (USP), São Carlos CEP 13566-590, SP, Brazil
2 shared publications - Flavio Colmati
Instituto de Química, Universidade Federal de Goiás, Goiânia, Brazil
2 shared publications - Guilhermina Ferreira Teixeira
Instituto de Química Universidade Federal de Goiás Goiânia Brazil
2 shared publications
Latest Publications
- Open Access
- 17 August 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (4) , 73
Electrochemical Degradation of Diuron by Anodic Oxidation on a Commercial Ru0.3Ti0.7O2 Anode in a Sulfate Medium
This work presents the electrochemical degradation of the herbicide Diuron by anodic oxidation on a Ti/Ru0.3Ti0.7O2 metal mixed oxide anode using sulfate as the electrolyte. The study includes the influence of Diuron concentration and current density on anodic oxidation. The results evidence a first-order degradation, with the highest capacity achieved at 40 mA cm−2 and at an initial Diuron concentration of 38 mg L−1. Nevertheless, in terms of efficiency and energy demand, the operation at 10 mA cm−2 is favored due to the more efficient and less energy-consuming condition. To discern the optimum design and operation conditions, this work presents the results of a preliminary technical–economic analysis, demonstrating that, to minimize the total costs of the system, it is recommended to seek the most efficient conditions, i.e., the conditions demanding the lowest applied charges with the highest Diuron degradation. At the same time, attention must be given to the required cell voltage to not increase excessively the operating costs.
- 17 August 2023
- Published by MDPI AG in Chemengineering
- Vol. 7 (4) , 73
Open AccessElectrochemical Degradation of Diuron by Anodic Oxidation on a Commercial Ru0.3Ti0.7O2 Anode in a Sulfate Medium
This work presents the electrochemical degradation of the herbicide Diuron by anodic oxidation on a Ti/Ru0.3Ti0.7O2 metal mixed oxide anode using sulfate as the electrolyte. The study includes the influence of Diuron concentration and current density on anodic oxidation. The results evidence a first-order degradation, with the highest capacity achieved at 40 mA cm−2 and at an initial Diuron concentration of 38 mg L−1. Nevertheless, in terms of efficiency and energy demand, the operation at 10 mA cm−2 is favored due to the more efficient and less energy-consuming condition. To discern the optimum design and operation conditions, this work presents the results of a preliminary technical–economic analysis, demonstrating that, to minimize the total costs of the system, it is recommended to seek the most efficient conditions, i.e., the conditions demanding the lowest applied charges with the highest Diuron degradation. At the same time, attention must be given to the required cell voltage to not increase excessively the operating costs.
- Open Access
- 25 July 2023
- Published by MDPI AG in Preprints.org
Electrochemical Degradation of Diuron by anodic oxidation on DSA in sulfate medium
This work presents the electrochemical degradation of the herbicide Diuron by anodic oxidation on a Ti/Ru0.3Ti0.7O2 dimensionally stable anode (DSA) using sulfate as electrolyte. The study includes the influence of the Diuron concentration and the current density on the anodic oxidation. The results evidence a first-order degradation, with the highest degradation capacity achieved at 40 mA cm2 and an initial Diuron concentration of 38 mg L1. Nevertheless, in terms of efficiency and energy demand, the operation at 10 mA cm2 is favored due to the more efficient and less energy-consuming condition. To discern the optimum design and operation conditions, this work presents the results of a preliminary technical-economical analysis, demonstrating that, to minimize the total costs of the system, it is recommended to seek the most efficient conditions, i.e., the conditions demanding the lowest applied charges with the highest Diuron degradation. At the same time, attention must be given to the required cell voltage to not increase excessively the operating costs.
- 25 July 2023
- Published by MDPI AG in Preprints.org
Open AccessElectrochemical Degradation of Diuron by anodic oxidation on DSA in sulfate medium
This work presents the electrochemical degradation of the herbicide Diuron by anodic oxidation on a Ti/Ru0.3Ti0.7O2 dimensionally stable anode (DSA) using sulfate as electrolyte. The study includes the influence of the Diuron concentration and the current density on the anodic oxidation. The results evidence a first-order degradation, with the highest degradation capacity achieved at 40 mA cm2 and an initial Diuron concentration of 38 mg L1. Nevertheless, in terms of efficiency and energy demand, the operation at 10 mA cm2 is favored due to the more efficient and less energy-consuming condition. To discern the optimum design and operation conditions, this work presents the results of a preliminary technical-economical analysis, demonstrating that, to minimize the total costs of the system, it is recommended to seek the most efficient conditions, i.e., the conditions demanding the lowest applied charges with the highest Diuron degradation. At the same time, attention must be given to the required cell voltage to not increase excessively the operating costs.
- 25 June 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (24) , 24850-24862
Activated carbon produced from waste coffee grounds for an effective removal of bisphenol-A in aqueous medium
Bisphenol-A is widely used chemical in industry and unfortunately often detected in natural waters. Considered as an emerging pollutant, bisphenol-A represents an environmental problem due to its endocrine-disrupting behavior. The production of activated carbon from alternative precursors has shown to be attractive in the removal of emerging pollutants from the water. Activated carbon was produced from waste coffee by physical and chemical activation and applied in the removal of bisphenol-A. The samples were characterized by elemental analysis, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and analysis of textural properties. Bisphenol-A adsorption experiments showed that the chemically activated carbon was more efficient due to its high specific surface area (1039 m2/g) compared to the physically activated carbon (4.0 m2/g). The bisphenol-A adsorption data followed the pseudo-second-order model and Langmuir isotherm, which indicated a maximum adsorption capacity of 123.22 mg/g for chemically activated carbon. The results demonstrated a potential use of the coffee grounds as a sustainable raw material for the production of chemically activated carbon that could be used in water treatment.
- 25 June 2019
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 26 (24) , 24850-24862
Activated carbon produced from waste coffee grounds for an effective removal of bisphenol-A in aqueous medium
Bisphenol-A is widely used chemical in industry and unfortunately often detected in natural waters. Considered as an emerging pollutant, bisphenol-A represents an environmental problem due to its endocrine-disrupting behavior. The production of activated carbon from alternative precursors has shown to be attractive in the removal of emerging pollutants from the water. Activated carbon was produced from waste coffee by physical and chemical activation and applied in the removal of bisphenol-A. The samples were characterized by elemental analysis, scanning electron microscopy, X-ray diffraction, Fourier transform infrared spectroscopy, and analysis of textural properties. Bisphenol-A adsorption experiments showed that the chemically activated carbon was more efficient due to its high specific surface area (1039 m2/g) compared to the physically activated carbon (4.0 m2/g). The bisphenol-A adsorption data followed the pseudo-second-order model and Langmuir isotherm, which indicated a maximum adsorption capacity of 123.22 mg/g for chemically activated carbon. The results demonstrated a potential use of the coffee grounds as a sustainable raw material for the production of chemically activated carbon that could be used in water treatment.
- 17 April 2019
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 206 (11) , 1498-1514
A new approach to obtain mesoporous-activated carbon via hydrothermal carbonization of Brazilian Cerrado biomass combined with physical activation for bisphenol-A removal
The worrying hydric crisis and the increasing water contamination by emerging pollutants around the world stimulate the development of activated carbons (AC) for the removal of endocrine disruptors, including bisphenol-A (BPA). For this reason, a new approach for the synthesis of AC from hydrochar produced through hydrothermal carbonization (HTC) of Brazilian Cerrado biomass (Magonia pubescens–Sapindaceae) and physical activation using water vapor is highlighted. Compared to the traditional method of physical activation after pyrolysis, HTC was found to be better option to develop the specific surface area, porosity, and yield of the ACs, which presented mesoporous structure and carbon content higher than 80%. The BPA adsorption was evaluated by varying the contact time, BPA concentration, and pH. The Langmuir, Freundlich, and Redlich–Peterson isotherms were used to model the adsorption behavior. In the preliminary test to verify the adsorption efficiency, the AC obtained from hydrochar treated at 180 °C presented better results compared to commercial AC. The BPA adsorption data of the best treated hydrochar correlated well with the pseudo first-order model and the Langmuir isotherm (Qmax = 21.26 mg g−1). The results of the studies indicated the combination of HTC and physical activation with steam to be an efficient way to prepare an ecologically sound adsorbent for removal of Bisphenol-A from water with lower temperature and without chemical reagents. The ACs obtained can also be potential materials for other applications, such as in the field of catalysis and environmental remediation.
- 17 April 2019
- Published by Taylor & Francis in Chemical Engineering Communications
- Vol. 206 (11) , 1498-1514
A new approach to obtain mesoporous-activated carbon via hydrothermal carbonization of Brazilian Cerrado biomass combined with physical activation for bisphenol-A removal
The worrying hydric crisis and the increasing water contamination by emerging pollutants around the world stimulate the development of activated carbons (AC) for the removal of endocrine disruptors, including bisphenol-A (BPA). For this reason, a new approach for the synthesis of AC from hydrochar produced through hydrothermal carbonization (HTC) of Brazilian Cerrado biomass (Magonia pubescens–Sapindaceae) and physical activation using water vapor is highlighted. Compared to the traditional method of physical activation after pyrolysis, HTC was found to be better option to develop the specific surface area, porosity, and yield of the ACs, which presented mesoporous structure and carbon content higher than 80%. The BPA adsorption was evaluated by varying the contact time, BPA concentration, and pH. The Langmuir, Freundlich, and Redlich–Peterson isotherms were used to model the adsorption behavior. In the preliminary test to verify the adsorption efficiency, the AC obtained from hydrochar treated at 180 °C presented better results compared to commercial AC. The BPA adsorption data of the best treated hydrochar correlated well with the pseudo first-order model and the Langmuir isotherm (Qmax = 21.26 mg g−1). The results of the studies indicated the combination of HTC and physical activation with steam to be an efficient way to prepare an ecologically sound adsorbent for removal of Bisphenol-A from water with lower temperature and without chemical reagents. The ACs obtained can also be potential materials for other applications, such as in the field of catalysis and environmental remediation.