Marek Buran
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marek Buran has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Pavol Kovac
Institute of Electrical Engineering, Slovak Academy of Sciences, Dubravska cesta 9, 841 04 Bratislava, Slovakia
7 shared publications - Lubomir Kopera
Slovak Academy of Sciences
6 shared publications - Fedor Gömöry
Institute of Electrical Engineering, Slovak Academy of Sciences, Bratislava, Slovakia
3 shared publications - Ján Kováč
Institute of Electrical Engineering, Slovak Academy of Sciences - Institute of Electrical Engineering, Bratislava, SLOVAKIA
3 shared publications T Melišek
Institute of Electrical Engineering of SAS, 841 04 Bratislava, Slovakia
3 shared publicationsD Berek
Institute of Electrical Engineering, Slovak Academy of Sciences, Dubravska cesta 9, 841 04 Bratislava, Slovakia
2 shared publications
Latest Publications
- Open Access
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. PP (10518223) , 1-9
Thermal Parameter Estimation for HVDC MgB2 Concentric Superconducting Cables
This paper presents a methodology for the estimation of thermal conductances in HVDC MgB2 concentric superconducting cables, with both analytical formulas and finiteelement method (FEM) simulations. A three-conductor thermal network representing the former, the MgB2 layer, and the shield has been developed to quantify the inter-layer heat exchange and assess the impact of temperature-dependent material properties. FEM results for the SCARLET ±25 kV / 20 kA case study show that a variation of thermal conductance with temperature, and that non-reciprocal effects between heating and cooling phases are negligible, allowing a three-conductance simple network to be employed. Consequently, linear analytical models have been proposed to accurately calculate the thermal conductance coefficients with minimal computational cost, enabling fast and reliable parameter identification for circuit-level electrothermal simulations of large-scale superconducting transmission systems.
- 6 April 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Applied Superconductivity
- Vol. PP (10518223) , 1-9
Open AccessThermal Parameter Estimation for HVDC MgB2 Concentric Superconducting Cables
This paper presents a methodology for the estimation of thermal conductances in HVDC MgB2 concentric superconducting cables, with both analytical formulas and finiteelement method (FEM) simulations. A three-conductor thermal network representing the former, the MgB2 layer, and the shield has been developed to quantify the inter-layer heat exchange and assess the impact of temperature-dependent material properties. FEM results for the SCARLET ±25 kV / 20 kA case study show that a variation of thermal conductance with temperature, and that non-reciprocal effects between heating and cooling phases are negligible, allowing a three-conductance simple network to be employed. Consequently, linear analytical models have been proposed to accurately calculate the thermal conductance coefficients with minimal computational cost, enabling fast and reliable parameter identification for circuit-level electrothermal simulations of large-scale superconducting transmission systems.
- Open Access
- 26 January 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2)
Multi-pulse current technique used for Ic and thermal stability assessment of HTS superconductors
Multi-pulse current (MPC) technique has been developed for advanced characterization of critical currents and electro-thermal stability of composite superconductors especially under conditions, where the critical current magnitude is large and electrothermal stability is relatively low. Short current pulses of 30 ms duration enable the measurement of high critical currents in composite superconductors without undesirable heating. The resulting E–I characteristics were compared with those obtained using the conventional DC method under various cooling conditions. Transport characterization of a 4-mm-wide REBCO tape with a filamentary structure was performed over a wide temperature range down to 20 K under applied magnetic fields up to 10 T and transport currents up to 350 A. Longer current pulses (of up to 1 s) enable the analysis of the electro-thermal stability of the same sample in liquid nitrogen (LN2) at 77 K and in subcooled water (H2O) ice at temperatures below 77 K. Investigations of the electrothermal stability confirmed enhanced heat extraction capabilities of H2O ice compare to conventional LN2 bath cooling. The tape exhibits advanced stability performances at lower temperature despite was exposed to magnetic field up to 1 T, at temperature of 62.5 K the energy required to initiate a quench was approximately 8 times higher compared to experiment performed at 75 K, assuming the same Ic value.
- 26 January 2026
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 39 (2)
Open AccessMulti-pulse current technique used for Ic and thermal stability assessment of HTS superconductors
Multi-pulse current (MPC) technique has been developed for advanced characterization of critical currents and electro-thermal stability of composite superconductors especially under conditions, where the critical current magnitude is large and electrothermal stability is relatively low. Short current pulses of 30 ms duration enable the measurement of high critical currents in composite superconductors without undesirable heating. The resulting E–I characteristics were compared with those obtained using the conventional DC method under various cooling conditions. Transport characterization of a 4-mm-wide REBCO tape with a filamentary structure was performed over a wide temperature range down to 20 K under applied magnetic fields up to 10 T and transport currents up to 350 A. Longer current pulses (of up to 1 s) enable the analysis of the electro-thermal stability of the same sample in liquid nitrogen (LN2) at 77 K and in subcooled water (H2O) ice at temperatures below 77 K. Investigations of the electrothermal stability confirmed enhanced heat extraction capabilities of H2O ice compare to conventional LN2 bath cooling. The tape exhibits advanced stability performances at lower temperature despite was exposed to magnetic field up to 1 T, at temperature of 62.5 K the energy required to initiate a quench was approximately 8 times higher compared to experiment performed at 75 K, assuming the same Ic value.
- 25 September 2024
- Published by Elsevier in Cryogenics
- Vol. 143
Numerical modelling and measurement of the E-I characteristics of MgB2 wire in sub-cooled water ice
- 25 September 2024
- Published by Elsevier in Cryogenics
- Vol. 143
Numerical modelling and measurement of the E-I characteristics of MgB2 wire in sub-cooled water ice
- 1 September 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (10) , 105013
E–I characteristics and critical currents of small Bi-2223/Ag coil thermally stabilized by solid and liquid nitrogen compared to water ice
A small-sized coil of helically wound Bi-2223/Ag tape was measured in liquid/solid nitrogen (LN2/SN2), and also in water (H2O) ice at external fields of 0–8 T and in a temperature range of 10–77 K. This work is especially focused on the coil stability for current amplitudes above the critical current criterion of 1 µV cm−1. While the E–I characteristics measured under the critical current criterion did not show any substantial variances at these different cooling conditions, significant differences were observed above the critical current magnitude, mainly upon cooling by solid nitrogen and water ice. The results confirm improved thermal stability for the coil measured in sub-cooled water ice compared to solid nitrogen. Consequently, cooling by water ice could be interesting for future applications of high-temperature superconducting coils.
- 1 September 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (10) , 105013
E–I characteristics and critical currents of small Bi-2223/Ag coil thermally stabilized by solid and liquid nitrogen compared to water ice
A small-sized coil of helically wound Bi-2223/Ag tape was measured in liquid/solid nitrogen (LN2/SN2), and also in water (H2O) ice at external fields of 0–8 T and in a temperature range of 10–77 K. This work is especially focused on the coil stability for current amplitudes above the critical current criterion of 1 µV cm−1. While the E–I characteristics measured under the critical current criterion did not show any substantial variances at these different cooling conditions, significant differences were observed above the critical current magnitude, mainly upon cooling by solid nitrogen and water ice. The results confirm improved thermal stability for the coil measured in sub-cooled water ice compared to solid nitrogen. Consequently, cooling by water ice could be interesting for future applications of high-temperature superconducting coils.
- 3 March 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (4) , 045014
Influence of filament number and size on the basic properties of in situ made MgB2 wires
Monel-sheathed MgB2 wires with 6, 18 and 54 filaments of diameter 0.83 mm manufactured by Sam Dong Co., Ltd, have been subjected to twisting, drawing and rolling and measurements at low temperatures. R(T), I–V characteristics, critical currents and stress/strain tolerances of these wires were analyzed. Low reduction of critical current (⩽10%) by twisting between 50 mm and 12.5 mm was observed, especially for the wire with 54 filaments, which also showed the best strain tolerance to tension, ∼0.43% at 4.2 K. The engineering current density of the 18-filament wire was decreased by 56% by drawing from 0.83 mm to 0.4 mm, but improved by ∼24% by rolling from 0.83 mm to 0.64 mm. A small uninsulated coil was made from wire flattened from 0.83 mm to 0.64 mm by the wind and react process, resulting in a very high winding packing factor of 0.91 and also a high winding current density of 104 A cm−2 at B ⩽ 5.6 T. The presented properties are interesting for possible applications of these MgB2 wires in DC windings.
- 3 March 2023
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 36 (4) , 045014
Influence of filament number and size on the basic properties of in situ made MgB2 wires
Monel-sheathed MgB2 wires with 6, 18 and 54 filaments of diameter 0.83 mm manufactured by Sam Dong Co., Ltd, have been subjected to twisting, drawing and rolling and measurements at low temperatures. R(T), I–V characteristics, critical currents and stress/strain tolerances of these wires were analyzed. Low reduction of critical current (⩽10%) by twisting between 50 mm and 12.5 mm was observed, especially for the wire with 54 filaments, which also showed the best strain tolerance to tension, ∼0.43% at 4.2 K. The engineering current density of the 18-filament wire was decreased by 56% by drawing from 0.83 mm to 0.4 mm, but improved by ∼24% by rolling from 0.83 mm to 0.64 mm. A small uninsulated coil was made from wire flattened from 0.83 mm to 0.64 mm by the wind and react process, resulting in a very high winding packing factor of 0.91 and also a high winding current density of 104 A cm−2 at B ⩽ 5.6 T. The presented properties are interesting for possible applications of these MgB2 wires in DC windings.
- 24 August 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (10) , 105004
Transport measurement of MgB2 wire under the sub-cooled water ice compared to other cooling conditions
The standard DC transport measurements of MgB2 composite conductors were done in vacuum, low-pressure helium gas, sub-cooled solid nitrogen and water ice. The effect of these coolants on electro-thermal behaviour was studied at self-field and temperature range from 32 K to 36.5 K. The obtained results show that even small volume of Helium gas enhances the sample thermal stability during the I–V measurement in comparison to those obtained in vacuum. The cooling by solid nitrogen improves the sample stability in contrast to helium gas. The measurements performed inn water ice exhibits an excellent and stable behavior of superconducting wire carrying high transport current below and above the quench as well. Consequently, water ice shows simple, safe, and promising He-free mode of cooling for future superconducting systems.
- 24 August 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (10) , 105004
Transport measurement of MgB2 wire under the sub-cooled water ice compared to other cooling conditions
The standard DC transport measurements of MgB2 composite conductors were done in vacuum, low-pressure helium gas, sub-cooled solid nitrogen and water ice. The effect of these coolants on electro-thermal behaviour was studied at self-field and temperature range from 32 K to 36.5 K. The obtained results show that even small volume of Helium gas enhances the sample thermal stability during the I–V measurement in comparison to those obtained in vacuum. The cooling by solid nitrogen improves the sample stability in contrast to helium gas. The measurements performed inn water ice exhibits an excellent and stable behavior of superconducting wire carrying high transport current below and above the quench as well. Consequently, water ice shows simple, safe, and promising He-free mode of cooling for future superconducting systems.
- 28 July 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (9) , 095007
Behaviour of Al2O3-oxide insulated and non-insulated superconducting MgB2 coils cooled by water ice
Wind-and-react coils made using non-insulated and/or Al2O3 oxide-insulated internal magnesium diffusion-processed MgB2 wires were energized at low temperatures with the help of sub-cooled water ice. The results demonstrate thermally stable winding behaviour and current densities (>104 A cm−2 for T < 30.5–33 K) of oxide-insulated and metal-insulated MgB2 coils. The expansion caused by the water-to-ice transformation does not degrade the windings or the Al2O3 insulation. The thermometers and Hall probe are also undamaged over the full temperature range of 27–297 K. Consequently, water ice provides a cheap and safe prospective cooling mode for various superconducting windings and future He-free systems.
- 28 July 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (9) , 095007
Behaviour of Al2O3-oxide insulated and non-insulated superconducting MgB2 coils cooled by water ice
Wind-and-react coils made using non-insulated and/or Al2O3 oxide-insulated internal magnesium diffusion-processed MgB2 wires were energized at low temperatures with the help of sub-cooled water ice. The results demonstrate thermally stable winding behaviour and current densities (>104 A cm−2 for T < 30.5–33 K) of oxide-insulated and metal-insulated MgB2 coils. The expansion caused by the water-to-ice transformation does not degrade the windings or the Al2O3 insulation. The thermometers and Hall probe are also undamaged over the full temperature range of 27–297 K. Consequently, water ice provides a cheap and safe prospective cooling mode for various superconducting windings and future He-free systems.
- Open Access
- 17 March 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (5) , 055001
Water ice-cooled MgB2 coil made by wind and react process
A wind and react (W&R) coil of inner diameter 53 mm has been made from multi-core MgB2/Nb/CuNi wire manufactured by the internal magnesium diffusion (IMD) process. The W&R coil is wound from non-insulated rectangular wire of 1 mm2 with only 5 µm thick stainless steel foil used for interlayer insulation. The transport current performance of the coil and short wire samples was measured in a liquid He bath at external magnetic fields of 4.5–8.5 T and also in self-field conditions in sub-cooled water ice at temperatures between 33 K and 38 K. The presented MgB2 coil exhibits stable behavior at water ice cooling, and its high space factor allows a high current density of winding in comparison to the data from the already published MgB2 coils. The presented results demonstrate that MgB2 windings can be used safely in He-free conditions inside sub-cooled water ice, and this technique can be further optimized and used for future MgB2 coils.
- 17 March 2022
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 35 (5) , 055001
Open AccessWater ice-cooled MgB2 coil made by wind and react process
A wind and react (W&R) coil of inner diameter 53 mm has been made from multi-core MgB2/Nb/CuNi wire manufactured by the internal magnesium diffusion (IMD) process. The W&R coil is wound from non-insulated rectangular wire of 1 mm2 with only 5 µm thick stainless steel foil used for interlayer insulation. The transport current performance of the coil and short wire samples was measured in a liquid He bath at external magnetic fields of 4.5–8.5 T and also in self-field conditions in sub-cooled water ice at temperatures between 33 K and 38 K. The presented MgB2 coil exhibits stable behavior at water ice cooling, and its high space factor allows a high current density of winding in comparison to the data from the already published MgB2 coils. The presented results demonstrate that MgB2 windings can be used safely in He-free conditions inside sub-cooled water ice, and this technique can be further optimized and used for future MgB2 coils.
- 3 June 2021
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 34 (7) , 075010
Low‐purity Cu and Al sheathed multi‐core MgB 2 wires made by IMD process
Up to now, the highest current densities of MgB 2 superconducting wires have been obtained by the internal magnesium diffusion (IMD) method. MgB 2 superconductors are especially suitable for DC or AC windings generating low or medium magnetic fields, where thermal stability and low AC losses are important issues. Mechanical, thermal and electrical parameters of the wires are strongly influenced by metallic materials used for the outer sheath. While highly electrical conductive sheath material is beneficial for thermally stable behaviour, it has a great effect on the generation of high eddy current losses. To minimize the contribution of eddy current losses, multi-core MgB 2 wires with low purity Cu and Al sheaths were prepared by the IMD process and characterized in detail. Results of low temperature measurements are analysed and discussed in the present work.
- 3 June 2021
- Published by IOP Publishing in Superconductor Science and Technology
- Vol. 34 (7) , 075010
Low‐purity Cu and Al sheathed multi‐core MgB 2 wires made by IMD process
Up to now, the highest current densities of MgB 2 superconducting wires have been obtained by the internal magnesium diffusion (IMD) method. MgB 2 superconductors are especially suitable for DC or AC windings generating low or medium magnetic fields, where thermal stability and low AC losses are important issues. Mechanical, thermal and electrical parameters of the wires are strongly influenced by metallic materials used for the outer sheath. While highly electrical conductive sheath material is beneficial for thermally stable behaviour, it has a great effect on the generation of high eddy current losses. To minimize the contribution of eddy current losses, multi-core MgB 2 wires with low purity Cu and Al sheaths were prepared by the IMD process and characterized in detail. Results of low temperature measurements are analysed and discussed in the present work.
- Open Access
Composite Heat Sink Material for Superconducting Tape in Fault Current Limiter Applications
We enhanced the performance of superconducting tapes during quenching by coating the tapes with various composites, with regards to the application of such coated systems in superconducting fault current limiters. In composition of the coating, we varied the type of epoxy matrix, the content of ceramic filler particles and the use of reinforcement in order to optimize the thermal and the mechanical stability of the coated tapes. By this way modified superconducting tapes were able to reduce the maximum temperature 170 °C of not modified superconducting tape to 55 °C during the quench with electric field up to 130 V m−1.
Open AccessComposite Heat Sink Material for Superconducting Tape in Fault Current Limiter Applications
We enhanced the performance of superconducting tapes during quenching by coating the tapes with various composites, with regards to the application of such coated systems in superconducting fault current limiters. In composition of the coating, we varied the type of epoxy matrix, the content of ceramic filler particles and the use of reinforcement in order to optimize the thermal and the mechanical stability of the coated tapes. By this way modified superconducting tapes were able to reduce the maximum temperature 170 °C of not modified superconducting tape to 55 °C during the quench with electric field up to 130 V m−1.