Christy Roshini Paul Inbaraj
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Christy Roshini Paul Inbaraj has a total of 101 co-authors. Here are the top co-authors by number of shared publications:
- Yu-Ming Liao
Department of Physics, National Taiwan University, Taipei 106, Taiwan
11 shared publications - Hung-I Lin
Department of Physics, National Taiwan University, Taipei 106, Taiwan
9 shared publications - Monika Kataria
Department of Physics, National Taiwan University, Taipei 10617, Taiwan
9 shared publications - Yang-Fang Chen
Department of Physics, National Taiwan University 1 , Taipei 10617
9 shared publications - Yit-Tsong Chen
Department of Chemistry National Taiwan University Taipei 10617 Taiwan
9 shared publications - Raman Sankar
Academia Sinica
8 shared publications
Latest Publications
- Open Access
- 28 May 2023
- Published by Wiley in Advanced Electronic Materials
- Vol. 9 (8)
An Anti‐Ambipolar Cryo‐Phototransistor
Novel anti‐ambipolar transistors (AATs) are gate tunable rectifiers with a marked potential for multi‐valued logic circuits. In this work, the optoelectronic applications of AATs in cryogenic conditions are studied, of which the AAT devices consist of vertically stacked p‐SnS and n‐ MoSe2 nanoflakes to form a type‐II staggered band alignment. An electrostatically tunable p‐SnS/n‐MoSe2 cryo‐phototransistor is presented with unique anti‐ambipolar characteristics and cryogenic‐enhanced optoelectronic performance. The cryo‐phototransistor exhibits a sharp and highly symmetric anti‐ambipolar transfer curve at 77 K with the peak‐to‐valley ratio of 103 operating under a low bias voltage of 1 V. The high cooling‐enhanced charge mobilities in the cryo‐phototransistor grant this AAT device remarkable photodetection capabilities. At 77 K, the p‐SnS/n‐MoSe2 cryo‐phototransistor, holding a broad photoresponse in the spectral range of 250−900 nm, demonstrates its high responsivity of 2 × 104 A W−1 and detectivity of 7.5 × 1013 Jones with the excitation at 532 nm. The high‐performance p‐SnS/n‐MoSe2 low‐dimensional phototransistor with low operating voltages at 77−150 K is eligible for optoelectronic applications in cryogenic environments. Furthermore, the cryo‐characteristics of this heterostructure can be further extended to design the mul‐tivalued logic circuits operated in cryogenic conditions.
- 28 May 2023
- Published by Wiley in Advanced Electronic Materials
- Vol. 9 (8)
Open AccessAn Anti‐Ambipolar Cryo‐Phototransistor
Novel anti‐ambipolar transistors (AATs) are gate tunable rectifiers with a marked potential for multi‐valued logic circuits. In this work, the optoelectronic applications of AATs in cryogenic conditions are studied, of which the AAT devices consist of vertically stacked p‐SnS and n‐ MoSe2 nanoflakes to form a type‐II staggered band alignment. An electrostatically tunable p‐SnS/n‐MoSe2 cryo‐phototransistor is presented with unique anti‐ambipolar characteristics and cryogenic‐enhanced optoelectronic performance. The cryo‐phototransistor exhibits a sharp and highly symmetric anti‐ambipolar transfer curve at 77 K with the peak‐to‐valley ratio of 103 operating under a low bias voltage of 1 V. The high cooling‐enhanced charge mobilities in the cryo‐phototransistor grant this AAT device remarkable photodetection capabilities. At 77 K, the p‐SnS/n‐MoSe2 cryo‐phototransistor, holding a broad photoresponse in the spectral range of 250−900 nm, demonstrates its high responsivity of 2 × 104 A W−1 and detectivity of 7.5 × 1013 Jones with the excitation at 532 nm. The high‐performance p‐SnS/n‐MoSe2 low‐dimensional phototransistor with low operating voltages at 77−150 K is eligible for optoelectronic applications in cryogenic environments. Furthermore, the cryo‐characteristics of this heterostructure can be further extended to design the mul‐tivalued logic circuits operated in cryogenic conditions.
- 7 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (15) , 19121-19128
Coupling between Pyroelectricity and Built-In Electric Field Enabled Highly Sensitive Infrared Phototransistor Based on InSe/WSe2/P(VDF-TrFE) Heterostructure
The assorted utilization of infrared detectors induces the demand for more comprehensive and high-performance electronic devices that work at room temperature. The intricacy of the fabrication process with bulk material limits the exploration in this field. However, two-dimensional (2D) materials with a narrow band gap opening aid in infrared (IR) detection relatively, but the photodetection range is narrowed due to the inherent band gap. In this study, we report an unprecedented attempt at the coordinated use of both 2D heterostructure (InSe/WSe2) and the dielectric polymer (poly(vinylidene fluoride-trifluoroethylene), P(VDF-TrFE)) for both visible and IR photodetection in a single device. The remnant polarization due to the ferroelectric effect of the polymer dielectric enhances the photocarrier separation in the visible range, resulting in high photoresponsivity. On the other hand, the pyroelectric effect of the polymer dielectric causes a change in the device current due to the increased temperature induced by the localized heating effect of the IR irradiation, which results in the change of ferroelectric polarization and induces the redistribution of charge carriers. In turn, it changes the built-in electric field, the depletion width, and the band alignment across the p-n heterojunction interface. Consequently, the charge carrier separation and the photosensitivity are therefore enhanced. Through the coupling between pyroelectricity and built-in electric field across the heterojunction, the specific detectivity for the photon energy below the band gap of the constituent 2D materials can reach up to 1011 Jones, which is better than all reported pyroelectric IR detectors. The proposed approach combining the ferroelectric and pyroelectric effects of the dielectric as well as exceptional properties of the 2D heterostructures can spark the design of advanced and not-yet realized optoelectronic devices.
- 7 April 2023
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 15 (15) , 19121-19128
Coupling between Pyroelectricity and Built-In Electric Field Enabled Highly Sensitive Infrared Phototransistor Based on InSe/WSe2/P(VDF-TrFE) Heterostructure
The assorted utilization of infrared detectors induces the demand for more comprehensive and high-performance electronic devices that work at room temperature. The intricacy of the fabrication process with bulk material limits the exploration in this field. However, two-dimensional (2D) materials with a narrow band gap opening aid in infrared (IR) detection relatively, but the photodetection range is narrowed due to the inherent band gap. In this study, we report an unprecedented attempt at the coordinated use of both 2D heterostructure (InSe/WSe2) and the dielectric polymer (poly(vinylidene fluoride-trifluoroethylene), P(VDF-TrFE)) for both visible and IR photodetection in a single device. The remnant polarization due to the ferroelectric effect of the polymer dielectric enhances the photocarrier separation in the visible range, resulting in high photoresponsivity. On the other hand, the pyroelectric effect of the polymer dielectric causes a change in the device current due to the increased temperature induced by the localized heating effect of the IR irradiation, which results in the change of ferroelectric polarization and induces the redistribution of charge carriers. In turn, it changes the built-in electric field, the depletion width, and the band alignment across the p-n heterojunction interface. Consequently, the charge carrier separation and the photosensitivity are therefore enhanced. Through the coupling between pyroelectricity and built-in electric field across the heterojunction, the specific detectivity for the photon energy below the band gap of the constituent 2D materials can reach up to 1011 Jones, which is better than all reported pyroelectric IR detectors. The proposed approach combining the ferroelectric and pyroelectric effects of the dielectric as well as exceptional properties of the 2D heterostructures can spark the design of advanced and not-yet realized optoelectronic devices.
- 27 February 2022
- Published by Wiley in Advanced Optical Materials
- Vol. 10 (8)
Near‐Infrared Electroluminescent Light‐Emitting Transistors Based on CVD‐Synthesized Ambipolar ReSe2 Nanosheets
Near‐infrared light‐emitting technology is ideal for noncontact diagnostic medical imaging and high‐speed data communications. High‐quality ReSe2 nanosheets of anisotropic single‐crystal structure with a bandgap of 1.26 eV (≈984 nm) are synthesized with an atmospheric pressure chemical vapor deposition (APCVD) method. The as‐synthesized ReSe2 nanosheets‐fabricated light‐emitting transistors (LETs) exhibit nearly symmetric ambipolar characteristics in electrical transport. Judicious selection of asymmetric platinum (Pt)/chromium (Cr) electrodes, with their work functions matching respectively the conduction‐ and valence‐band edges of ambipolar ReSe2, generates a low turn‐on voltage ReSe2‐LET with the balanced number density and field‐effect mobility of bipolar carriers (i.e., electrons and holes). Room‐temperature near‐infrared electroluminescence (NIR EL) from the frequency‐modulated ReSe2‐LET has been observed unprecedentedly with the assistance of a lock‐in detection system. The NIR EL intensity is tested by varying the bias voltage applied to the ReSe2‐LET devices with different channel lengths. The wavelength of the NIR EL from ReSe2‐LET is differentiated with optical bandpass filters. Room‐temperature angle‐dependent two lobe‐shaped EL pattern manifests the inherent anisotropic in‐plane excitonic polarization of the ReSe2 crystal. The highly stable NIR EL from ReSe2‐LETs provides prospective 2D material‐based ultrathin scalable data communication electronics for future development.
- 27 February 2022
- Published by Wiley in Advanced Optical Materials
- Vol. 10 (8)
Near‐Infrared Electroluminescent Light‐Emitting Transistors Based on CVD‐Synthesized Ambipolar ReSe2 Nanosheets
Near‐infrared light‐emitting technology is ideal for noncontact diagnostic medical imaging and high‐speed data communications. High‐quality ReSe2 nanosheets of anisotropic single‐crystal structure with a bandgap of 1.26 eV (≈984 nm) are synthesized with an atmospheric pressure chemical vapor deposition (APCVD) method. The as‐synthesized ReSe2 nanosheets‐fabricated light‐emitting transistors (LETs) exhibit nearly symmetric ambipolar characteristics in electrical transport. Judicious selection of asymmetric platinum (Pt)/chromium (Cr) electrodes, with their work functions matching respectively the conduction‐ and valence‐band edges of ambipolar ReSe2, generates a low turn‐on voltage ReSe2‐LET with the balanced number density and field‐effect mobility of bipolar carriers (i.e., electrons and holes). Room‐temperature near‐infrared electroluminescence (NIR EL) from the frequency‐modulated ReSe2‐LET has been observed unprecedentedly with the assistance of a lock‐in detection system. The NIR EL intensity is tested by varying the bias voltage applied to the ReSe2‐LET devices with different channel lengths. The wavelength of the NIR EL from ReSe2‐LET is differentiated with optical bandpass filters. Room‐temperature angle‐dependent two lobe‐shaped EL pattern manifests the inherent anisotropic in‐plane excitonic polarization of the ReSe2 crystal. The highly stable NIR EL from ReSe2‐LETs provides prospective 2D material‐based ultrathin scalable data communication electronics for future development.
- 14 September 2021
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 8 (10) , 2955-2965
Highly Efficient Photodetection in Metal Nanocluster/Graphene Heterojunctions
- 14 September 2021
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 8 (10) , 2955-2965
Highly Efficient Photodetection in Metal Nanocluster/Graphene Heterojunctions
- 9 September 2021
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 8 (10) , 3051-3060
Generation of Silver Metal Nanocluster Random Lasing
- 9 September 2021
- Published by American Chemical Society (ACS) in ACS Photonics
- Vol. 8 (10) , 3051-3060
Generation of Silver Metal Nanocluster Random Lasing
- 10 May 2021
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 15 (5) , 8686-8693
A Bi-Anti-Ambipolar Field Effect Transistor
Multistate logic is recognized as a promising approach to increase the device density of microelectronics, but current approaches are offset by limited performance and large circuit complexity. We here demonstrate a route toward increased integration density that is enabled by a mechanically tunable device concept. Bi-anti-ambipolar transistors (bi-AATs) exhibit two distinct peaks in their transconductance and can be realized by a single 2D-material heterojunction-based solid-state device. Dynamic deformation of the device reveals the co-occurrence of two conduction pathways to be the origin of this previously unobserved behavior. Initially, carrier conduction proceeds through the junction edge, but illumination and application of strain can increase the recombination rate in the junction sufficiently to support an alternative carrier conduction path through the junction area. Optical characterization reveals a tunable emission pattern and increased optoelectronic responsivity that corroborates our model. Strain control permits the optimization of the conduction efficiency through both pathways and can be employed in quaternary inverters for future multilogic applications.
- 10 May 2021
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 15 (5) , 8686-8693
A Bi-Anti-Ambipolar Field Effect Transistor
Multistate logic is recognized as a promising approach to increase the device density of microelectronics, but current approaches are offset by limited performance and large circuit complexity. We here demonstrate a route toward increased integration density that is enabled by a mechanically tunable device concept. Bi-anti-ambipolar transistors (bi-AATs) exhibit two distinct peaks in their transconductance and can be realized by a single 2D-material heterojunction-based solid-state device. Dynamic deformation of the device reveals the co-occurrence of two conduction pathways to be the origin of this previously unobserved behavior. Initially, carrier conduction proceeds through the junction edge, but illumination and application of strain can increase the recombination rate in the junction sufficiently to support an alternative carrier conduction path through the junction area. Optical characterization reveals a tunable emission pattern and increased optoelectronic responsivity that corroborates our model. Strain control permits the optimization of the conduction efficiency through both pathways and can be employed in quaternary inverters for future multilogic applications.
- 13 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (23) , 26213-26221
Modulating Charge Separation with Hexagonal Boron Nitride Mediation in Vertical Van der Waals Heterostructures
Tuning the optical and electrical properties by stacking different layers of two-dimensional (2D) materials enables to create unusual physical phenomena. Here, we demonstrate an alternative approach to enhance charge separation and alter physical properties in van der Waals heterojunctions with type-II band alignment by using thin dielectric spacers. To illustrate our working principle, we implement the h-BN sieve layer in between InSe/GeS heterojunction. The optical transitions at the junctions studied by photoluminescence and ultrafast pump-probe technique show quenching of emission without h-BN layers exhibiting an indirect recombination process. This quenching effect due to strong interlayer coupling was confirmed with Raman spectroscopic studies. In contrast, h-BN layers in between InSe and GeS show strong enhancement in emission giving another degree of freedom to tune the heterojunction property. The two-terminal photoresponse study supports the argument by showing a large photocurrent density for InSe/h-BN/GeS device by avoiding interlayer charge recombination. The enhanced charge separation with h-BN mediation manifests a photoresponsivity and detectivity as 9 × 10^2 A/W and 3.4 × 10^14 Jones, respectively. Moreover, a photogain of 1.7 × 10^3 shows the high detection of electrons for the incident photon. Interestingly, the photovoltaic short-circuit current is switched from positive to negative, while the open-circuit voltage changes from negative to positive. Our proposed enhancement of charge separation with 2D-insulator mediation, therefore, provides a useful route to manipulate the physical properties of heterostructures and for the future development of high-performance optoelectronic devices.
- 13 May 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (23) , 26213-26221
Modulating Charge Separation with Hexagonal Boron Nitride Mediation in Vertical Van der Waals Heterostructures
Tuning the optical and electrical properties by stacking different layers of two-dimensional (2D) materials enables to create unusual physical phenomena. Here, we demonstrate an alternative approach to enhance charge separation and alter physical properties in van der Waals heterojunctions with type-II band alignment by using thin dielectric spacers. To illustrate our working principle, we implement the h-BN sieve layer in between InSe/GeS heterojunction. The optical transitions at the junctions studied by photoluminescence and ultrafast pump-probe technique show quenching of emission without h-BN layers exhibiting an indirect recombination process. This quenching effect due to strong interlayer coupling was confirmed with Raman spectroscopic studies. In contrast, h-BN layers in between InSe and GeS show strong enhancement in emission giving another degree of freedom to tune the heterojunction property. The two-terminal photoresponse study supports the argument by showing a large photocurrent density for InSe/h-BN/GeS device by avoiding interlayer charge recombination. The enhanced charge separation with h-BN mediation manifests a photoresponsivity and detectivity as 9 × 10^2 A/W and 3.4 × 10^14 Jones, respectively. Moreover, a photogain of 1.7 × 10^3 shows the high detection of electrons for the incident photon. Interestingly, the photovoltaic short-circuit current is switched from positive to negative, while the open-circuit voltage changes from negative to positive. Our proposed enhancement of charge separation with 2D-insulator mediation, therefore, provides a useful route to manipulate the physical properties of heterostructures and for the future development of high-performance optoelectronic devices.
- 9 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (17) , 19840-19854
Self-Sufficient and Highly Efficient Gold Sandwich Upconversion Nanocomposite Lasers for Stretchable and Bio-applications
Multi-functional lanthanides doped upconversion nanoparticles (UCNP) have spread its wings in the fields of flexible optoelectronics and biomedical applications. One of the ongoing challenges lies in achieving UCNP based nanocomposites which enable continuous wave (CW) laser action at ultralow-threshold. Here, gold sandwich UCNP nanocomposites {gold (Au1)-UCNP-gold (Au2)} capable of exhibiting lasing at ultralow-thresholds under CW excitation is demonstrated. The metastable energy-level characteristics of lanthanides is advantageous for creating population inversion. In particular, localised surface plasmon resonance based electromagnetic hotspots in the nanocomposites and the giant enhancement of scattering coefficient for the formation of coherent closed loops due to multiple scattering facilitates the process of stimulated emissions as confirmed by theoretical simulation. The nanocomposites are subjected to stretchable systems for enhancing lasing action (threshold ~0.06 kW/cm2) via light trapping effect. The applications on bioimaging of HeLa cells and antibacterial activity (photothermal therapy) are demonstrated using the newly designed Au1-UCNP-Au2 nanocomposites.
- 9 April 2020
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 12 (17) , 19840-19854
Self-Sufficient and Highly Efficient Gold Sandwich Upconversion Nanocomposite Lasers for Stretchable and Bio-applications
Multi-functional lanthanides doped upconversion nanoparticles (UCNP) have spread its wings in the fields of flexible optoelectronics and biomedical applications. One of the ongoing challenges lies in achieving UCNP based nanocomposites which enable continuous wave (CW) laser action at ultralow-threshold. Here, gold sandwich UCNP nanocomposites {gold (Au1)-UCNP-gold (Au2)} capable of exhibiting lasing at ultralow-thresholds under CW excitation is demonstrated. The metastable energy-level characteristics of lanthanides is advantageous for creating population inversion. In particular, localised surface plasmon resonance based electromagnetic hotspots in the nanocomposites and the giant enhancement of scattering coefficient for the formation of coherent closed loops due to multiple scattering facilitates the process of stimulated emissions as confirmed by theoretical simulation. The nanocomposites are subjected to stretchable systems for enhancing lasing action (threshold ~0.06 kW/cm2) via light trapping effect. The applications on bioimaging of HeLa cells and antibacterial activity (photothermal therapy) are demonstrated using the newly designed Au1-UCNP-Au2 nanocomposites.
- 16 October 2019
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 13 (11) , 12540-12552
Graphene Sandwich Stable Perovskite Quantum-Dot Light-Emissive Ultrasensitive and Ultrafast Broadband Vertical Phototransistors
The dual-functional devices, which can simultaneously detect light and emit light, have a tremendous appeal for multiple applications, including display, sensors, defense, and high-speed optical communication. Despite the tremendous efforts of scientists, the progress of integration of phototransistor, where the built-in electric field separates the photogenerated excitons, and light-emitting diode (LED), where the radiative recombination can be enhanced by band offset, into a single device remains a challenge. Combining the superior properties of perovskite quantum dots (PQDs) and graphene, here we report a light-emissive, ultrasensitive, ultrafast, and broadband vertical phototransistor, which can simultaneously act as an efficient photodetector and light emitter within a single device. The estimated value of external quantum efficiency (EQE) of the vertical phototransistor is ~ 1.2×1010% and photoresponsivity > 109 AW-1 with response time of < 50 µs, which exceed all the presently reported vertical phototransistor devices. We also demonstrate that the modulation of the Dirac point of graphene efficiently tunes both amplitude and polarity of the photocurrent. The device exhibits a green emission having a quantum efficiency of 5.6%. The moisture insensitive and environmentally stable, light-emissive, ultrafast, and ultrasensitive broadband phototransistor creates a useful route for dual-functional optoelectronic devices.
- 16 October 2019
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 13 (11) , 12540-12552
Graphene Sandwich Stable Perovskite Quantum-Dot Light-Emissive Ultrasensitive and Ultrafast Broadband Vertical Phototransistors
The dual-functional devices, which can simultaneously detect light and emit light, have a tremendous appeal for multiple applications, including display, sensors, defense, and high-speed optical communication. Despite the tremendous efforts of scientists, the progress of integration of phototransistor, where the built-in electric field separates the photogenerated excitons, and light-emitting diode (LED), where the radiative recombination can be enhanced by band offset, into a single device remains a challenge. Combining the superior properties of perovskite quantum dots (PQDs) and graphene, here we report a light-emissive, ultrasensitive, ultrafast, and broadband vertical phototransistor, which can simultaneously act as an efficient photodetector and light emitter within a single device. The estimated value of external quantum efficiency (EQE) of the vertical phototransistor is ~ 1.2×1010% and photoresponsivity > 109 AW-1 with response time of < 50 µs, which exceed all the presently reported vertical phototransistor devices. We also demonstrate that the modulation of the Dirac point of graphene efficiently tunes both amplitude and polarity of the photocurrent. The device exhibits a green emission having a quantum efficiency of 5.6%. The moisture insensitive and environmentally stable, light-emissive, ultrafast, and ultrasensitive broadband phototransistor creates a useful route for dual-functional optoelectronic devices.
- 7 August 2019
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 13 (8) , 8977-8985
Self-Healing Nanophotonics: Robust and Soft Random Lasers
Self-healing technology promises a generation of innovation in cross-cutting subjects ranging from electronic skins, to wearable electronics, to point-of-care biomedical sensing modules. Recently, scientists have successfully pulled off significant advances in self-healing components including sensors, energy devices, transistors, and even integrated circuits. Lasers, one of the most important light sources, integrated with autonomous self-healability should be endowed with more functionalities and opportunities; however, the study of self-healing lasers is absent in all published reports. Here, the soft and self-healable random laser (SSRL) is presented. The SSRL can not only endure extreme external strain but also withstand several cutting/healing test cycles. Particularly, the damaged SSRL enables its functionality to be restored within just few minutes without the need of additional energy, chemical/electrical agents, or other healing stimuli, truly exhibiting a supple yet robust laser prototype. It is believed that SSRL can serve as a vital building block for next-generation laser technology as well as follow-on self-healing optoelectronics.
- 7 August 2019
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 13 (8) , 8977-8985
Self-Healing Nanophotonics: Robust and Soft Random Lasers
Self-healing technology promises a generation of innovation in cross-cutting subjects ranging from electronic skins, to wearable electronics, to point-of-care biomedical sensing modules. Recently, scientists have successfully pulled off significant advances in self-healing components including sensors, energy devices, transistors, and even integrated circuits. Lasers, one of the most important light sources, integrated with autonomous self-healability should be endowed with more functionalities and opportunities; however, the study of self-healing lasers is absent in all published reports. Here, the soft and self-healable random laser (SSRL) is presented. The SSRL can not only endure extreme external strain but also withstand several cutting/healing test cycles. Particularly, the damaged SSRL enables its functionality to be restored within just few minutes without the need of additional energy, chemical/electrical agents, or other healing stimuli, truly exhibiting a supple yet robust laser prototype. It is believed that SSRL can serve as a vital building block for next-generation laser technology as well as follow-on self-healing optoelectronics.