LCLuca Del Carro

Luca Del Carro

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Luca Del Carro has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Oxide-Free Copper Pastes for the Attachment of Large-Area Power Devices

    by Luca Del Carro, Alfred A. Zinn, Patrick Ruch, Florian Bouville, André R. Studart, Thomas Brunschwiler


  • Low-Temperature Dip-Based All-Copper Interconnects Formed by Pressure-Assisted Sintering of Copper Nanoparticles

    by Luca Del Carro, Jonas Zurcher, Ute Drechsler, Ian E. Clark, Gustavo Ramos, Thomas Brunschwiler

    Flip-chip interconnects made entirely from copper are promising candidates to overcome the intrinsic limits of solder-based interconnects and match the demand for increased current densities of high-performance microprocessors. To this end, dip-based all-copper interconnects have been demonstrated to be a viable approach to form electrical interconnects by sintering copper nanoparticles between the copper pillar and pad. However, the performance of this technology is limited by residual porosity of the copper joint formed between the pillar and the pad during sintering. Moreover, the applicability of this technology in the printed circuit board industry is constrained by thermomechanical stresses that arise from the sintering. Furthermore, the compatibility of the sintering approach with standard finishing layers used as diffusion-barrier layers to provide wetting and to prevent the oxidation of the pillar and pad surfaces is unknown. In this paper, we pursue the advancement of dipbased all-copper interconnect technology. We demonstrate the robustness of dip-transfer of copper paste for varying withdrawal velocities and typical nonuniformities in copper pillar heights. Moreover, we prove the applicability of this technology with fine pillar diameters and pitches down to 10 and 20 μm, respectively. In addition, we demonstrate reduced porosities of the copper joints by applying pressure during the bonding process at 200 °C. This densification leads to interconnects with four times the shear strength and half the electrical resistance compared to interconnects formed without the application of pressure. In addition, the bonding temperature is decreased to 160 °C by applying a novel copper paste formulation, reducing the thermomechanical stress in the assembly caused by the cooling from the sintering temperature. Finally, the compatibility of this technology with EPAG, ENIG, and ENEPIG finishing layers is demonstrated, with resulting shear strength of the interconnects above 70 MPa and electrical resistance comparable to the unfinished samples.


  • On the Evaporation of Colloidal Suspensions in Confined Pillar Arrays

    by Jonas Zürcher, Brian R. Burg, Luca Del Carro, André R. Studart, Thomas Brunschwiler


  • Review on Percolating and Neck-Based Underfills for Three-Dimensional Chip Stacks

    by Thomas Brunschwiler, Jonas Zürcher, Luca Del Carro, Gerd Schlottig, Brian Burg, Severin Zimmermann, Uwe Zschenderlein, Bernhard Wunderle, Florian Schindler-Saefkow, Rahel Stässle

    Heat dissipation from three-dimensional (3D) chip stacks can cause large thermal gradients due to the accumulation of dissipated heat and thermal interfaces from each integrated die. To reduce the overall thermal resistance and thereby the thermal gradients, this publication will provide an overview of several studies on the formation of sequential thermal underfills that result in percolation and quasi-areal thermal contacts between the filler particles in the composite material. The quasi-areal contacts are formed from nanoparticles self-assembled by capillary bridging, so-called necks. Thermal conductivities of up to 2.5 W/m K and 2.8 W/m K were demonstrated experimentally for the percolating and the neck-based underfills, respectively. This is a substantial improvement with respect to a state-of-the-art capillary thermal underfill (0.7 W/m K). Critical parameters in the formation of sequential thermal underfills will be discussed, such as the material choice and refinement, as well as the characteristics and limitations of the individual process steps. Guidelines are provided on dry versus wet filling of filler particles, the optimal bimodal nanosuspension formulation and matrix material feed, and the over-pressure cure to mitigate voids in the underfill during backfilling. Finally, the sequential filling process is successfully applied on microprocessor demonstrator modules, without any detectable sign of degradation after 1500 thermal cycles, as well as to a two-die chip stack. The morphology and performance of the novel underfills are further discussed, ranging from particle arrangements in the filler particle bed, to cracks formed in the necks. The thermal and mechanical performance is benchmarked with respect to the capillary thermal and mechanical underfills. Finally, the thermal improvements within a chip stack are discussed. An 8 - or 16-die chip stack can dissipate 46% and 65% more power with the optimized neck-based thermal underfill than with a state-of-the-artcapillary thermal underfill.