Srawanti Medhi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Srawanti Medhi has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
Dharmender Kumar Gupta
3 shared publications- Satyajit Chowdhury
Department of Petroleum Engineering and Earth Sciences, University of Petroleum and Energy Studies, Dehradun, India
3 shared publications Jitendra S. Sangwai
2 shared publicationsAmit Kumar
1 shared publicationAryab Mazumdar
University of Petroleum and Energy Studies
1 shared publicationDharmendra K. Gupta
1 shared publication
Latest Publications
- 1 January 2021
- Published by Elsevier in Powder Technology
- Vol. 377, 379-395
Analysis of high performing graphene oxide nanosheets based non-damaging drilling fluids through rheological measurements and CFD studies
- 1 January 2021
- Published by Elsevier in Powder Technology
- Vol. 377, 379-395
Analysis of high performing graphene oxide nanosheets based non-damaging drilling fluids through rheological measurements and CFD studies
- 3 September 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 2385-2397
Effect of Al 2 O 3 nanoparticle on viscoelastic and filtration properties of a salt-polymer-based drilling fluid
Conventional bentonite-based drilling fluids have associated problems while drilling troublesome or high-temperature zone due to degradation of rheological properties and excessive fluid loss. Clay particles present in the drilling fluid tend to block the pore throats and cause blockage to hydrocarbon flow. Similarly, polymers along with the filtrate loss, in the invaded zone, alter the wettability due to which there is a reduction in relative permeability to oil. All of these factors collectively cause a fall in production rates and demand stimulation jobs. The use of nondamaging drilling fluids, a particle-free salt-polymer-based drilling fluid, has addressed these problems by yielding a substantially less filtrate loss. However, at moderately high depths with high temperatures, this drilling fluid fails to maintain rheological properties and hence sagging, carrying, and fluid loss problems remerge. Sagging increases the equivalent circulation density which eventually decreases rate of penetration and induces formation damages. Hence, a need to further improve its properties is much required. This study has investigated the effect of aluminum oxide nanoparticles (Al2O3 NP) on these salt-polymer-based drilling fluids. A significant change was observed in rheological and fluid loss properties of drilling fluid (DF) when doped with different concentrations (0.5%, 0.8%, and 1%) of Al2O3 NP compared to the Base DF. Steady shear (rotational) tests were conducted to study the degree of shear thinning behavior of all the drilling fluids. It was observed that shear thinning behavior of the DF was increased with the addition of Al2O3 NP. Rotational measurements at 30°C showed a decrease in viscosity and shear stress of Al2O3 NP DF with an increase in concentration. However, at elevated temperatures of 60°C and 80°C, the reduction in viscosity of Al2O3 NP DF was substantially less than Base DF. One percent Al2O3 NP DF showed higher viscosity as compared to 0.5%, 0.8% Al2O3 NP, and Base DF at these conditions. To investigate the viscoelastic properties, oscillation tests were performed. Amplitude sweep tests showed an increase in storage modulus (G’) with an increase in Al2O3 NP concentration. While Base and 0.5% Al2O3 NP DF showed viscoelastic liquid in nature, 0.8% and 1% Al2O3 NP DF showed dominant storage properties indicating its viscoelastic solid nature at 30°C, 60°C, and 80°C. From the frequency sweep tests at higher temperatures, 0.8% and 1% Al2O3 NP DF, unlike Base and 0.5% Al2O3 NP DF, showed increase in complex viscosity at lower frequencies indicating structural build-up. Both rotational and thixotropic tests showed less structural regain time for 1% Al2O3 NP DF compared to other drilling fluid. Lastly, fluid loss control property of all the drilling fluids was investigated by measuring the filtrate loss volume in an API filter press apparatus. One percent Al2O3 NP DF showed a greater reduction in filtrate volume with Base DF showing the highest.
- 3 September 2019
- Published by Taylor & Francis in Energy Sources, Part A: Recovery, Utilization, and Environmental Effects
- Vol. 45 (1) , 2385-2397
Effect of Al 2 O 3 nanoparticle on viscoelastic and filtration properties of a salt-polymer-based drilling fluid
Conventional bentonite-based drilling fluids have associated problems while drilling troublesome or high-temperature zone due to degradation of rheological properties and excessive fluid loss. Clay particles present in the drilling fluid tend to block the pore throats and cause blockage to hydrocarbon flow. Similarly, polymers along with the filtrate loss, in the invaded zone, alter the wettability due to which there is a reduction in relative permeability to oil. All of these factors collectively cause a fall in production rates and demand stimulation jobs. The use of nondamaging drilling fluids, a particle-free salt-polymer-based drilling fluid, has addressed these problems by yielding a substantially less filtrate loss. However, at moderately high depths with high temperatures, this drilling fluid fails to maintain rheological properties and hence sagging, carrying, and fluid loss problems remerge. Sagging increases the equivalent circulation density which eventually decreases rate of penetration and induces formation damages. Hence, a need to further improve its properties is much required. This study has investigated the effect of aluminum oxide nanoparticles (Al2O3 NP) on these salt-polymer-based drilling fluids. A significant change was observed in rheological and fluid loss properties of drilling fluid (DF) when doped with different concentrations (0.5%, 0.8%, and 1%) of Al2O3 NP compared to the Base DF. Steady shear (rotational) tests were conducted to study the degree of shear thinning behavior of all the drilling fluids. It was observed that shear thinning behavior of the DF was increased with the addition of Al2O3 NP. Rotational measurements at 30°C showed a decrease in viscosity and shear stress of Al2O3 NP DF with an increase in concentration. However, at elevated temperatures of 60°C and 80°C, the reduction in viscosity of Al2O3 NP DF was substantially less than Base DF. One percent Al2O3 NP DF showed higher viscosity as compared to 0.5%, 0.8% Al2O3 NP, and Base DF at these conditions. To investigate the viscoelastic properties, oscillation tests were performed. Amplitude sweep tests showed an increase in storage modulus (G’) with an increase in Al2O3 NP concentration. While Base and 0.5% Al2O3 NP DF showed viscoelastic liquid in nature, 0.8% and 1% Al2O3 NP DF showed dominant storage properties indicating its viscoelastic solid nature at 30°C, 60°C, and 80°C. From the frequency sweep tests at higher temperatures, 0.8% and 1% Al2O3 NP DF, unlike Base and 0.5% Al2O3 NP DF, showed increase in complex viscosity at lower frequencies indicating structural build-up. Both rotational and thixotropic tests showed less structural regain time for 1% Al2O3 NP DF compared to other drilling fluid. Lastly, fluid loss control property of all the drilling fluids was investigated by measuring the filtrate loss volume in an API filter press apparatus. One percent Al2O3 NP DF showed a greater reduction in filtrate volume with Base DF showing the highest.
- Open Access
- 1 July 2019
- Published by Springer Nature in Journal of Petroleum Exploration and Production Technology
- Vol. 10 (1) , 91-101
An investigation on the effects of silica and copper oxide nanoparticles on rheological and fluid loss property of drilling fluids
The increase in hydrocarbon production from problematic production zones having high fluid loss and formation damage has led to the emergence of non-damaging drilling fluids (NDDF). Recently, nanotechnology has found a wide array of applications in the oil and gas industry. Most applications of nanotechnology and enhancement in properties of drilling fluids are restricted to bentonite, xanthan gum and a few oil-based mud. In this study, the effects of silica and copper oxide nanoparticles on polyamine-based NDDF and conventional bentonite-based drilling fluids (BDF) were investigated. Silica nanoparticles were prepared using sol–gel method, and copper oxide nanoparticles were synthesized using co-precipitation method. Nano-based drilling fluids were prepared by dispersing nanoparticles in concentrations of 0.5%, 0.8% and 1% by weight. Furthermore, testing of these nano-based drilling fluids was conducted by measuring specific gravity, pH, rheological properties and filtrate loss at surface temperature (room temperature) and then aging it at bottom-hole temperature (80 °C). The addition of silica and copper oxide nanoparticles to both the drilling fluids did not show much effect on pH and specific gravity. Addition of 0.5% concentration of silica nanoparticles in NDDF showed least degradation in rheological properties compared to other fluids. It showed reduction in filtrate loss by 31%. Moreover, silica nanoparticles in conjunction with BDF acted as a mud thinner showing a decrease in viscosity and yield point. On the contrary, when used with NDDFs, silica nanoparticles acted as a mud thickener. Copper oxide nanoparticles behaved as a thinner in both the drilling fluids with a highest reduction in plastic viscosity of 24% for 0.8% of copper oxide nanoparticle in BDF. Thinning properties were enhanced as the doping concentrations of copper oxide nanoparticles increased; however, the fluid loss controlling ability decreased except for 0.5% concentration by 31% and 24% when used with both the drilling fluids. Additionally, optimal Herschel–Bulkley parameters have been determined by using genetic algorithm to minimize the function of sum of squared errors between observed values and model equation.
- 1 July 2019
- Published by Springer Nature in Journal of Petroleum Exploration and Production Technology
- Vol. 10 (1) , 91-101
Open AccessAn investigation on the effects of silica and copper oxide nanoparticles on rheological and fluid loss property of drilling fluids
The increase in hydrocarbon production from problematic production zones having high fluid loss and formation damage has led to the emergence of non-damaging drilling fluids (NDDF). Recently, nanotechnology has found a wide array of applications in the oil and gas industry. Most applications of nanotechnology and enhancement in properties of drilling fluids are restricted to bentonite, xanthan gum and a few oil-based mud. In this study, the effects of silica and copper oxide nanoparticles on polyamine-based NDDF and conventional bentonite-based drilling fluids (BDF) were investigated. Silica nanoparticles were prepared using sol–gel method, and copper oxide nanoparticles were synthesized using co-precipitation method. Nano-based drilling fluids were prepared by dispersing nanoparticles in concentrations of 0.5%, 0.8% and 1% by weight. Furthermore, testing of these nano-based drilling fluids was conducted by measuring specific gravity, pH, rheological properties and filtrate loss at surface temperature (room temperature) and then aging it at bottom-hole temperature (80 °C). The addition of silica and copper oxide nanoparticles to both the drilling fluids did not show much effect on pH and specific gravity. Addition of 0.5% concentration of silica nanoparticles in NDDF showed least degradation in rheological properties compared to other fluids. It showed reduction in filtrate loss by 31%. Moreover, silica nanoparticles in conjunction with BDF acted as a mud thinner showing a decrease in viscosity and yield point. On the contrary, when used with NDDFs, silica nanoparticles acted as a mud thickener. Copper oxide nanoparticles behaved as a thinner in both the drilling fluids with a highest reduction in plastic viscosity of 24% for 0.8% of copper oxide nanoparticle in BDF. Thinning properties were enhanced as the doping concentrations of copper oxide nanoparticles increased; however, the fluid loss controlling ability decreased except for 0.5% concentration by 31% and 24% when used with both the drilling fluids. Additionally, optimal Herschel–Bulkley parameters have been determined by using genetic algorithm to minimize the function of sum of squared errors between observed values and model equation.