Nikola Šibalić
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Nikola Šibalić has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
M. Vukčević
University of Montenegro, Faculty of Mechanical Engineering, Podgorica
2 shared publicationsMarko Mumović
University of Montenegro
2 shared publications- Darko Bajić
Univerzitet Crne Gore Mašinski Fakultet Podgorica Crna Gora
1 shared publication M. Mumović
University of Montenegro, Faculty of Mechanical Engineering, Podgorica
1 shared publication- Milan Vukcevic
Faculty of Mechanical Engineering, University of Montenegro, st. Dzordza Vasingtona bb, 81000 Podgorica, Montenegro
1 shared publication
Latest Publications
- Open Access
- 10 September 2023
- Published by National and University Library of the Republic of Srpska in JOURNAL OF ENGINEERING AND MANAGEMENT
- Vol. 1 (1)
Zavarivanje trenjem sa miješanjem - razvoj i primjena
Rad se odnosi na prikaz postupka Zavarivanja trenjem sa miješanjem (Friction Stir Welding), zatim daje kratku istoriju razvoja, primjenu u industriji, usvojenu terminologiju postupka, kao i pregled izabranih istraživanja. Suština procesa je zavarivanje u čvrstom stanju, gdje je izbjegnuto topljenje materijala, što postupak FSW svrstava u ekološki čiste i energetski efikasne postupke, sa izuzetno dobrim i pouzdanim karakteristikama zavarenog spoja. Velika prednost je u spajanju teško zavarivih istorodnih i raznorodnih materijala, korišćenjem rotirajućeg alata, uz generisanje toplote, tako da se materijal zagrijava, plastično deformiše i spaja u toplom stanju. Najveća primjena je kod zavarivanja sučeonih spojeva lima od legure aluminijuma u jednom prolazu debljine od 0.3 mm do 75 mm. U radu je dat i pregled jednog broja istraživanja postupka Zavarivanja trenjem sa miješanjem, koja se odnose na: limove različitih debljina i materijala, različitih spojeva, analizu mikrostrukture zavarenog spoja, tečenje materijala, praćenje temperature i komponenata sila, numeričke simulacije i mehanička ispitivanja. Dati su i budući pravci razvoja ove tehnologije.
- 10 September 2023
- Published by National and University Library of the Republic of Srpska in JOURNAL OF ENGINEERING AND MANAGEMENT
- Vol. 1 (1)
Open AccessZavarivanje trenjem sa miješanjem - razvoj i primjena
Rad se odnosi na prikaz postupka Zavarivanja trenjem sa miješanjem (Friction Stir Welding), zatim daje kratku istoriju razvoja, primjenu u industriji, usvojenu terminologiju postupka, kao i pregled izabranih istraživanja. Suština procesa je zavarivanje u čvrstom stanju, gdje je izbjegnuto topljenje materijala, što postupak FSW svrstava u ekološki čiste i energetski efikasne postupke, sa izuzetno dobrim i pouzdanim karakteristikama zavarenog spoja. Velika prednost je u spajanju teško zavarivih istorodnih i raznorodnih materijala, korišćenjem rotirajućeg alata, uz generisanje toplote, tako da se materijal zagrijava, plastično deformiše i spaja u toplom stanju. Najveća primjena je kod zavarivanja sučeonih spojeva lima od legure aluminijuma u jednom prolazu debljine od 0.3 mm do 75 mm. U radu je dat i pregled jednog broja istraživanja postupka Zavarivanja trenjem sa miješanjem, koja se odnose na: limove različitih debljina i materijala, različitih spojeva, analizu mikrostrukture zavarenog spoja, tečenje materijala, praćenje temperature i komponenata sila, numeričke simulacije i mehanička ispitivanja. Dati su i budući pravci razvoja ove tehnologije.
- 26 May 2022
- Published by Springer Nature
- p. 382-389
Information Measurement System for Determination of Cutting Force at Turning Technology
- 26 May 2022
- Published by Springer Nature
- p. 382-389
Information Measurement System for Determination of Cutting Force at Turning Technology
- Open Access
- 1 January 2022
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 67 (4) , 157-165
Study of welding of butt and fillet welds using the FSW method
In recent years, the unconventional FSW method has been increasingly used in industrial production, primarily for welding aluminium alloys or sheets of large length and thickness. Due to its specifics in relation to conventional methods, which primarily refer to rotating tools that have high productivity, i.e. service life, these methods allow us to obtain welded joints up to 1000 m in length with one tool. This procedure can also be used to obtain construction profiles such as "L" profile. In this paper, welding of a sheet of aluminium alloy 6082-T6 with a thickness of 7.8 mm is conducted with a butt and fillet welds, so that it is possible to perform a comparative analysis of welded joints. During the process, the components of the forces on the butt joint were measured in three normal directions (Fz, Fx, and Fy). FSW is an environmentally clean technology when compared to conventional processes because during the process the material does not melt, there are no harmful fumes, harmful radiation, light flash, no atmosphere of shielding gases or additional material, which characterizes all conventional processes. For the needs of this research, special auxiliary accessories were constructed and manufactured, as well as special shapes of conical tools.
- 1 January 2022
- Published by Društvo za unapređivanje zavarivanja u Srbiji - DUZS in Zavarivanje i zavarene konstrukcije
- Vol. 67 (4) , 157-165
Open AccessStudy of welding of butt and fillet welds using the FSW method
In recent years, the unconventional FSW method has been increasingly used in industrial production, primarily for welding aluminium alloys or sheets of large length and thickness. Due to its specifics in relation to conventional methods, which primarily refer to rotating tools that have high productivity, i.e. service life, these methods allow us to obtain welded joints up to 1000 m in length with one tool. This procedure can also be used to obtain construction profiles such as "L" profile. In this paper, welding of a sheet of aluminium alloy 6082-T6 with a thickness of 7.8 mm is conducted with a butt and fillet welds, so that it is possible to perform a comparative analysis of welded joints. During the process, the components of the forces on the butt joint were measured in three normal directions (Fz, Fx, and Fy). FSW is an environmentally clean technology when compared to conventional processes because during the process the material does not melt, there are no harmful fumes, harmful radiation, light flash, no atmosphere of shielding gases or additional material, which characterizes all conventional processes. For the needs of this research, special auxiliary accessories were constructed and manufactured, as well as special shapes of conical tools.
- 15 October 2019
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 53 (5) , 711-715
Research on the quality of the welded joint of aluminium alloy sheet AA6082-T6 using FSW, MIG and TIG methods
- 15 October 2019
- Published by Institute of Metals and Technology in Materiali in tehnologije
- Vol. 53 (5) , 711-715
Research on the quality of the welded joint of aluminium alloy sheet AA6082-T6 using FSW, MIG and TIG methods
- Open Access
Numerical Simulation for FSW Process at Welding Aluminium Alloy AA6082-T6
This paper presents the numerical simulation of the Friction stir welding (FSW) process obtained by using the DEFORM 3D software package. Numerical simulations are based on experimental research, welding of aluminum alloy AA6082-T6 by FSW method, which has the thickness of 7.8 mm. The aim of this paper is to determine the reliability of numerical simulations in the FSW process, which is followed by large deformations, where influential geometric and kinematic parameters are varied. Numerical research was done on the basis of the adopted five-phase orthogonal experimental plan with a variety of factors on two levels and repetition at the central point of the plan for four times. The parameters varied in the experiment are: Welding speed v mm/min, a rotation speed of tool ω rpm, angle of pin slopes α o, a diameter of the pin d mm, diameter of the shoulder D mm. During the performing of the FSW process, forces were measured in three normal directions: Axial force Fz, longitudinal force Fx and side force Fy, as well as the temperature in the adopted measuring positions of the workpiece. The experimental results obtained in this way were compared with the numerical experiment in the same adopted measuring positions, i.e., in the paper an analysis and comparison of the obtained experimental and numerical data of the measured forces and the generated temperature field were made.
Open AccessNumerical Simulation for FSW Process at Welding Aluminium Alloy AA6082-T6
This paper presents the numerical simulation of the Friction stir welding (FSW) process obtained by using the DEFORM 3D software package. Numerical simulations are based on experimental research, welding of aluminum alloy AA6082-T6 by FSW method, which has the thickness of 7.8 mm. The aim of this paper is to determine the reliability of numerical simulations in the FSW process, which is followed by large deformations, where influential geometric and kinematic parameters are varied. Numerical research was done on the basis of the adopted five-phase orthogonal experimental plan with a variety of factors on two levels and repetition at the central point of the plan for four times. The parameters varied in the experiment are: Welding speed v mm/min, a rotation speed of tool ω rpm, angle of pin slopes α o, a diameter of the pin d mm, diameter of the shoulder D mm. During the performing of the FSW process, forces were measured in three normal directions: Axial force Fz, longitudinal force Fx and side force Fy, as well as the temperature in the adopted measuring positions of the workpiece. The experimental results obtained in this way were compared with the numerical experiment in the same adopted measuring positions, i.e., in the paper an analysis and comparison of the obtained experimental and numerical data of the measured forces and the generated temperature field were made.