Yuji Watanabe
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yuji Watanabe has a total of 2 co-authors. Here are the top co-authors by number of shared publications:
Mitsuo Iijima
Department of Electronics and Systems, Faculty of Engineering, Takushoku University, Hachioji, Tokyo 193-0985, Japan
1 shared publication- Sayuri Tarvainen1 shared publication
Latest Publications
- 28 June 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (SG) , SGGD15
A design method of applied voltage waveform for high-power ultrasonic monopole pulses
Our previous studies demonstrated that an ultrasonic monopole pulse with ringing suppression can be generated by utilizing a half sine voltage waveform and its generating method. The resultant vibration amplitude of the ultrasonic monopole pulse is too small for high-power ultrasonic application. However, ringing suppression provides advantages for a minimized jumping phenomenon, and can be applied to improve surface quality when machining hard and brittle material. A small displacement of vibration amplitude is suitable to reduce the finish machining margin, while suppressing microcracking and chipping. In addition, machining application using an ultrasonic monopole pulse is predominately unreported. Therefore, we design a bolt-clamped Langevin type transducer with a tool clamping system for generating a high-power ultrasonic monopole pulse with suppression ringing for the experimentation of ultrasonic burnishing and the observed effect upon the machined surface.
- 28 June 2019
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 58 (SG) , SGGD15
A design method of applied voltage waveform for high-power ultrasonic monopole pulses
Our previous studies demonstrated that an ultrasonic monopole pulse with ringing suppression can be generated by utilizing a half sine voltage waveform and its generating method. The resultant vibration amplitude of the ultrasonic monopole pulse is too small for high-power ultrasonic application. However, ringing suppression provides advantages for a minimized jumping phenomenon, and can be applied to improve surface quality when machining hard and brittle material. A small displacement of vibration amplitude is suitable to reduce the finish machining margin, while suppressing microcracking and chipping. In addition, machining application using an ultrasonic monopole pulse is predominately unreported. Therefore, we design a bolt-clamped Langevin type transducer with a tool clamping system for generating a high-power ultrasonic monopole pulse with suppression ringing for the experimentation of ultrasonic burnishing and the observed effect upon the machined surface.
- 1 May 2001
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 40 (5S) , 3789
Ultrasonic Joining of Silicon Nitride Plates Without an Adhesive Material Using a 19 kHz Vibration System
In recent years, we have attempted ultrasonic ceramic joining for the purpose of extending the application field of ultrasonic joining. By devising a vibration system, the authors have attempted ceramic ultrasonic joining by which a metal becomes an intermediate material. In this method, however, the high temperature resistance and strength of the joint are dependent on the melting point and strength of the metallic material. Therefore, in this study, we attempted ultrasonic joining of silicon nitride (Si3N4) plates without using any intermediate material. The experimental result showed that ultrasonic joining was possible without using the intermediate material. The maximum joint strength was 33 MPa and the joining time required was about 10 s.
- 1 May 2001
- Published by IOP Publishing in Japanese Journal of Applied Physics
- Vol. 40 (5S) , 3789
Ultrasonic Joining of Silicon Nitride Plates Without an Adhesive Material Using a 19 kHz Vibration System
In recent years, we have attempted ultrasonic ceramic joining for the purpose of extending the application field of ultrasonic joining. By devising a vibration system, the authors have attempted ceramic ultrasonic joining by which a metal becomes an intermediate material. In this method, however, the high temperature resistance and strength of the joint are dependent on the melting point and strength of the metallic material. Therefore, in this study, we attempted ultrasonic joining of silicon nitride (Si3N4) plates without using any intermediate material. The experimental result showed that ultrasonic joining was possible without using the intermediate material. The maximum joint strength was 33 MPa and the joining time required was about 10 s.