Aigerim Tazhen
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Aigerim Tazhen has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Merlan Dosbolayev
Institute of Experimental and Theoretical Physics, Al-Farabi Kazakh National University, Almaty 050040, Kazakhstan
10 shared publications - Tlekkabul S. Ramazanov
NNLOT, Al-Farabi Kazakh National University, 71 Al-Farabi Ave., Almaty 050040, Kazakhstan
7 shared publications - Yerbolat Ussenov
Princeton University
3 shared publications - A. N. Kholmirzayev
Natiоnal Nanotechnоlogy Laboratоry of Open Type, al-Farabi Кazakh National University
2 shared publications T.S. Ramazanov
2 shared publicationsA. U. Utegenov
Al-Farabi Kazakh National University, Almaty, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 388-397
USA STUDY OF CHANGES IN MICROHARDNESS AND MASS OF A PREHEATED TUNGSTEN UNDER THE INFLUENCE OF PULSED PLASMA
The paper presents the results of an experimental investigation of changes in the microhardness and mass of a preheated tungsten target, the primary candidate material for the first wall and divertor, subjected to a pulsed plasma flow of approximately 0.2 ms duration. The experiments were conducted as a series of 13 pulses, each with an energy density and power density of approximately 1.1 MJ/m 2 and 5.5 GW/m 2 , respectively. Microhardness was measured using an HVS-1000B hardness tester; the target mass before and after plasma exposure was measured using a CPA225D precision balance. It is shown that the microhardness of the tungsten target remains virtually unchanged even at the maximum irradiation dose (up to 39 pulses), and the observed change is within the measurement error, which indicates the structural stability of the surface layer. At the same time, an increase in the target mass (up to 31 mg) was recorded, probably caused by contamination and redeposition of the material of external structural components. Energy-dispersive spectroscopy (EDS) analysis revealed Cu, Zn, Ni, and C lines in dust particles redeposited on the target surface. The results indicate that these foreign components have a significant impact on surface morphology and should be considered when interpreting tungsten damage mechanisms.
- 22 September 2026
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 23 (3) , 388-397
Open AccessUSA STUDY OF CHANGES IN MICROHARDNESS AND MASS OF A PREHEATED TUNGSTEN UNDER THE INFLUENCE OF PULSED PLASMA
The paper presents the results of an experimental investigation of changes in the microhardness and mass of a preheated tungsten target, the primary candidate material for the first wall and divertor, subjected to a pulsed plasma flow of approximately 0.2 ms duration. The experiments were conducted as a series of 13 pulses, each with an energy density and power density of approximately 1.1 MJ/m 2 and 5.5 GW/m 2 , respectively. Microhardness was measured using an HVS-1000B hardness tester; the target mass before and after plasma exposure was measured using a CPA225D precision balance. It is shown that the microhardness of the tungsten target remains virtually unchanged even at the maximum irradiation dose (up to 39 pulses), and the observed change is within the measurement error, which indicates the structural stability of the surface layer. At the same time, an increase in the target mass (up to 31 mg) was recorded, probably caused by contamination and redeposition of the material of external structural components. Energy-dispersive spectroscopy (EDS) analysis revealed Cu, Zn, Ni, and C lines in dust particles redeposited on the target surface. The results indicate that these foreign components have a significant impact on surface morphology and should be considered when interpreting tungsten damage mechanisms.
- Open Access
- 2 October 2024
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 21 (3) , 273-280
MEASUREMENT OF THE VELOCITY OF PULSED PLASMA FLOW AT THE PW-7 INSTALLATION
The paper considers two independent methods for measuring the velocity of the plasma flow generated in the PV-7 pulsed plasma accelerator: a method based on observation and evaluation of the Doppler shift of spectral lines, and a method of high-speed visualization of plasma motion. To record the plasma flow radiation spectrum, a monochromator M833 was used. High-speed video recording was carried out at 640,000 fps using a Phantom VEO710S CMOS camera. The results of measurements of the average flow velocity obtained at a working gas pressure of 2⋅10-2 Torr, capacitance and voltage of the capacitor bank of 400 μF and 4 kV are presented. The results obtained by two independent methods were compared with each other. Argon was used as the working gas in the experiments. It is shown that the value of the plasma flow velocity estimated by the first method is 12.5 m/s, and the value of the plasma flow velocity estimated by the second method is 16.7 m/s. From these data the measured flow velocity values have a small discrepancy. Thus, it has been established that high-speed video recording and Doppler shift methods make it possible to obtain comparable estimates of flow velocity within the measurement errors. Determining the magnitude of the plasma flow velocity is of great practical importance.
- 2 October 2024
- Published by Kazakh-British Technical University in Herald of the Kazakh-British technical university
- Vol. 21 (3) , 273-280
Open AccessMEASUREMENT OF THE VELOCITY OF PULSED PLASMA FLOW AT THE PW-7 INSTALLATION
The paper considers two independent methods for measuring the velocity of the plasma flow generated in the PV-7 pulsed plasma accelerator: a method based on observation and evaluation of the Doppler shift of spectral lines, and a method of high-speed visualization of plasma motion. To record the plasma flow radiation spectrum, a monochromator M833 was used. High-speed video recording was carried out at 640,000 fps using a Phantom VEO710S CMOS camera. The results of measurements of the average flow velocity obtained at a working gas pressure of 2⋅10-2 Torr, capacitance and voltage of the capacitor bank of 400 μF and 4 kV are presented. The results obtained by two independent methods were compared with each other. Argon was used as the working gas in the experiments. It is shown that the value of the plasma flow velocity estimated by the first method is 12.5 m/s, and the value of the plasma flow velocity estimated by the second method is 16.7 m/s. From these data the measured flow velocity values have a small discrepancy. Thus, it has been established that high-speed video recording and Doppler shift methods make it possible to obtain comparable estimates of flow velocity within the measurement errors. Determining the magnitude of the plasma flow velocity is of great practical importance.
- Open Access
- 18 October 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 37
Studies of the formation and distribution of cracks and various defects on the heated tungsten plate surface during pulsed plasma flux impact
- 18 October 2023
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 37
Open AccessStudies of the formation and distribution of cracks and various defects on the heated tungsten plate surface during pulsed plasma flux impact
- Open Access
- 7 June 2023
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 10 (1-2) , 42-49
Investigation of the plasma column evolution and dynamics in the PW-7 plasma accelerator
In this paper the results of measurements of the azimuthal component distribution of the plasma column magnetic field in the coaxial plasma accelerator PW-7 are presented. Registration of the magnetic field was performed by the magnetic probe method. The objective of the work is to investigate the plasma column dynamics and temporal evolution distribution by the magnetic field. It has been revealed that by using a dielectric (quartz) tube limiting the plasma column, the escape of charged particles from the discharge onto the walls of the vacuum chamber can be avoided. Through the use of a dielectric tube, the redistribution of the plasma column current in the accelerator led to a change in the shape of the probe signals. In addition, the plasma velocity was measured by the time of the plasma column front, passing between the bottom of the coaxial electrode and probe measuring system. Using a rectangular screen composed of ferromagnetic material provided magnetic shielding from the quasi-static magnetic fields of the plasma jumper between the electrodes. These results allowed investigating the major peculiarities of the complex behavior of the plasma column. The main objectives of investigations at the PW-7 facility include a detailed analysis of the probe system operation, studying the effects of different discharge scenarios on the magnetic probe signals.
- 7 June 2023
- Published by al-Farabi Kazakh National University in Physical Sciences and Technology
- Vol. 10 (1-2) , 42-49
Open AccessInvestigation of the plasma column evolution and dynamics in the PW-7 plasma accelerator
In this paper the results of measurements of the azimuthal component distribution of the plasma column magnetic field in the coaxial plasma accelerator PW-7 are presented. Registration of the magnetic field was performed by the magnetic probe method. The objective of the work is to investigate the plasma column dynamics and temporal evolution distribution by the magnetic field. It has been revealed that by using a dielectric (quartz) tube limiting the plasma column, the escape of charged particles from the discharge onto the walls of the vacuum chamber can be avoided. Through the use of a dielectric tube, the redistribution of the plasma column current in the accelerator led to a change in the shape of the probe signals. In addition, the plasma velocity was measured by the time of the plasma column front, passing between the bottom of the coaxial electrode and probe measuring system. Using a rectangular screen composed of ferromagnetic material provided magnetic shielding from the quasi-static magnetic fields of the plasma jumper between the electrodes. These results allowed investigating the major peculiarities of the complex behavior of the plasma column. The main objectives of investigations at the PW-7 facility include a detailed analysis of the probe system operation, studying the effects of different discharge scenarios on the magnetic probe signals.
- Open Access
- 8 November 2022
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 33, 101300
Investigation of dust formation during changes in the structural and surface properties of plasma-irradiated materials
- 8 November 2022
- Published by Elsevier in Nuclear Materials and Energy
- Vol. 33, 101300
Open AccessInvestigation of dust formation during changes in the structural and surface properties of plasma-irradiated materials
- Open Access
- 1 June 2022
- Published by al-Farabi Kazakh National University in Recent Contributions to Physics
- Vol. 81 (2) , 35-39
Pulsed plasma flow diagnostics
This paper presents the results of optical and probe diagnostics of hydrogen plasma flow in a coaxial plasma accelerator. The triple probe and the Optosky ATP2000P linear spectrometer with a spectral range of 200-1100 nm were used for measuring the electron current and obtaining the hydrogen plasma emission spectrum. The individual spectral lines were observed using an M833 monochromator spectrometer with a spectral resolution of 0.024 nm. From the measured electron currents and emission spectrums, the electron densities in the flux of a hydrogen pulsed plasma were calculated. We used the Stark method of Hβ hydrogen line broadening for calculations of electron densities. The obtained experimental results from the probe and spectroscopic measurements of electron density correspond well. In this work, we also obtained the dependence of the electron density on the voltages applied to the capacitor bank. The electron density increases with increasing voltage, because of the increased energy applied to the discharge. The average electron densities in the plasma flux showed 1.13 ∙ 1021 m-3, 4.14 ∙ 1021 m-3, and 5.57 ∙ 1021 m-3 at three values of voltages of 3 kV, 4 kV, and 5 kV, respectively. В работе представлены результаты оптической и зондовой диагностики водородного плазменного потока в коаксиальном плазменном ускорителе. Для измерения электронного тока и получения эмиссионных спектров водородной плазмы были использованы тройной зонд и соответственно линейный спектрометр Optosky ATP2000P со спектральным диапазоном 200-1100 нм. Отдельные спектральные линии были сняты с помощью спектрометра-монохроматора М833 со спектральным разрешением 0,024 нм. На основе измеренных электронных токов и отождествленных эмиссионных спектров были рассчитаны плотности электронов в потоке импульсной водородной плазмы. Для расчёта плотности электронов был использован метод Штарковского уширения водородных линий Hβ. Полученные экспериментальные результаты зондового и спектроскопического измерения плотности электронов хорошо согласуются. В этой работе также была получена зависимость плотности электронов от приложенного к конденсаторной батарее зарядового напряжения. С увеличением зарядового напряжения увеличивается плотность электронов, что связано с увеличением энергии вложенной в разряд. При трех значениях зарядового напряжения 3 кВ, 4 кВ и 5 кВ, средние значения плотности электронов в плазменном потоке составили 1,13 ∙ 1021 м-3, 4,14 ∙ 1021 м-3, и 5,57 ∙ 1021 м-3, соответственно. Бұл жұмыста коаксиалды плазмалық үдеткіштегі сутегі плазмалық ағынының оптикалық және зондтық диагностикасының нәтижелері ұсынылған. Электрондық токты өлшеу және сутегі плазмасының эмиссиялық спектрлерін алу үшін үшэлектродты зонд және 200-1100 нм спектрлік диапазонда зерттеуге мүмкіндік беретін Optosky ATP2000P сызықтық спектрометрі қолданылды. Жеке спектрлік сызықтар 0,024 нм спектрлік ажыратқыштық қабілеті бар М833 монохроматор спектрометрінің көмегімен алынды. Өлшенген электрондық токтар мен алынған эмиссиялық спектрлер негізінде импульстік сутегі плазмасының ағынындағы электрондардың тығыздығы есептелді. Электрондардың тығыздығын есептеу үшін Hβ сутегі спектрінің Штарктық кеңею әдісі қолданылды. Электрондардың тығыздығын зондтық және спектроскопиялық өлшеудің тәжірибелік нәтижелері жақсы сәйкес келді. Сонымен қатар бұл жұмыста электрондар тығыздығының конденсатор батареясына түсірілген кернеуге тәуелділігі де алынды. Кернеудің жоғарылауымен электрондардың тығыздығы да артады, бұл разрядқа берілген энергияның артуымен тығыз байланысты. 3 кВ, 4 кВ және 5 кВ кернеуінің үш мәні үшін плазмалық ағындағы электрондар тығыздығының орташа мәндері сәйкесінше 1,13 ∙ 1021 м-3, 4,14 ∙ 1021 м-3, және 5,57 ∙ 1021 м-3 құрады.
- 1 June 2022
- Published by al-Farabi Kazakh National University in Recent Contributions to Physics
- Vol. 81 (2) , 35-39
Open AccessPulsed plasma flow diagnostics
This paper presents the results of optical and probe diagnostics of hydrogen plasma flow in a coaxial plasma accelerator. The triple probe and the Optosky ATP2000P linear spectrometer with a spectral range of 200-1100 nm were used for measuring the electron current and obtaining the hydrogen plasma emission spectrum. The individual spectral lines were observed using an M833 monochromator spectrometer with a spectral resolution of 0.024 nm. From the measured electron currents and emission spectrums, the electron densities in the flux of a hydrogen pulsed plasma were calculated. We used the Stark method of Hβ hydrogen line broadening for calculations of electron densities. The obtained experimental results from the probe and spectroscopic measurements of electron density correspond well. In this work, we also obtained the dependence of the electron density on the voltages applied to the capacitor bank. The electron density increases with increasing voltage, because of the increased energy applied to the discharge. The average electron densities in the plasma flux showed 1.13 ∙ 1021 m-3, 4.14 ∙ 1021 m-3, and 5.57 ∙ 1021 m-3 at three values of voltages of 3 kV, 4 kV, and 5 kV, respectively. В работе представлены результаты оптической и зондовой диагностики водородного плазменного потока в коаксиальном плазменном ускорителе. Для измерения электронного тока и получения эмиссионных спектров водородной плазмы были использованы тройной зонд и соответственно линейный спектрометр Optosky ATP2000P со спектральным диапазоном 200-1100 нм. Отдельные спектральные линии были сняты с помощью спектрометра-монохроматора М833 со спектральным разрешением 0,024 нм. На основе измеренных электронных токов и отождествленных эмиссионных спектров были рассчитаны плотности электронов в потоке импульсной водородной плазмы. Для расчёта плотности электронов был использован метод Штарковского уширения водородных линий Hβ. Полученные экспериментальные результаты зондового и спектроскопического измерения плотности электронов хорошо согласуются. В этой работе также была получена зависимость плотности электронов от приложенного к конденсаторной батарее зарядового напряжения. С увеличением зарядового напряжения увеличивается плотность электронов, что связано с увеличением энергии вложенной в разряд. При трех значениях зарядового напряжения 3 кВ, 4 кВ и 5 кВ, средние значения плотности электронов в плазменном потоке составили 1,13 ∙ 1021 м-3, 4,14 ∙ 1021 м-3, и 5,57 ∙ 1021 м-3, соответственно. Бұл жұмыста коаксиалды плазмалық үдеткіштегі сутегі плазмалық ағынының оптикалық және зондтық диагностикасының нәтижелері ұсынылған. Электрондық токты өлшеу және сутегі плазмасының эмиссиялық спектрлерін алу үшін үшэлектродты зонд және 200-1100 нм спектрлік диапазонда зерттеуге мүмкіндік беретін Optosky ATP2000P сызықтық спектрометрі қолданылды. Жеке спектрлік сызықтар 0,024 нм спектрлік ажыратқыштық қабілеті бар М833 монохроматор спектрометрінің көмегімен алынды. Өлшенген электрондық токтар мен алынған эмиссиялық спектрлер негізінде импульстік сутегі плазмасының ағынындағы электрондардың тығыздығы есептелді. Электрондардың тығыздығын есептеу үшін Hβ сутегі спектрінің Штарктық кеңею әдісі қолданылды. Электрондардың тығыздығын зондтық және спектроскопиялық өлшеудің тәжірибелік нәтижелері жақсы сәйкес келді. Сонымен қатар бұл жұмыста электрондар тығыздығының конденсатор батареясына түсірілген кернеуге тәуелділігі де алынды. Кернеудің жоғарылауымен электрондардың тығыздығы да артады, бұл разрядқа берілген энергияның артуымен тығыз байланысты. 3 кВ, 4 кВ және 5 кВ кернеуінің үш мәні үшін плазмалық ағындағы электрондар тығыздығының орташа мәндері сәйкесінше 1,13 ∙ 1021 м-3, 4,14 ∙ 1021 м-3, және 5,57 ∙ 1021 м-3 құрады.
- Open Access
- 1 June 2021
- Published by al-Farabi Kazakh National University in Recent Contributions to Physics
- Vol. 77 (2) , 30-39
Measuring the self-generated magnetic field and the velocity of plasma flow in a pulsed plasma accelerator
In phase of radial compression the unsteady plasma flow at the exit of a pulsed plasma accelerators is related to the generation of fast high-energy charged particle beams, to plasma density perturbations, to the internal plasma pressure is opposite to the external magnetic pressure (B2/2μ0) associated with plasma column’s self-generated magnetic field. The last one listed above is of particular interest. The investigation of the magnetic field of plasma flow relatively gives information about the above mutually close factors cause to plasma flow instability.In this paper a miniature high-frequency magnetic probe are made for measuring and further investigating the pulsed self-generated magnetic field of plasma flow, in particular, at the exit of the accelerator in an experimental setup of PPA (located in KazNU, IETP). The magnetic probe dimensions are following: coil diameter is 2,12 mm, number of turns is 7, copper wire diameter is 150 μm, and winding length is 1, 1 mm. The coil inductance is about 0,113 μH and the temporal resolution of the magnetic probe is 2,3 ns. The magnetic probe was calibrated using a Hall sensor on the magnetic field of a multi-layered solenoid connected to an alternating power source of 15 A. Thus, the evaluated measurement error of the probe was no more than 10%. Нестабильное течение плазменного сгустка на выходе из плазменных ускорителей в стадии радиального сжатия связано со многими факторами: генерацией высокоэнергичных пучков заряженных частиц, возмущением плотности, внутренним давлением плазмы обратного по направлению внешнему давление собственного магнитного поля плазменного шнура. Особый интерес из них вызывает последнее, исследование собственного магнитного поля плазменного потока, который относительно дает информацию и о вышесказанных взаимосвязанных между собой факторах.В этой работе нами был изготовлен высокочастотный магнитный зонд малого размера для измерения и дальнейшего исследования импульсного магнитного поля плазменного потока в экспериментальной установке ИПУ (КазНУ, НИИЭТФ), в частности на выходе из ускорителя. Магнитный зонд имеет следующие геометрические размеры: диаметр катушки – 2,12 мм, число витков – 7, диаметр медного провода – 150 мкм, длина намотки – 1,1 мм. Индуктивность катушки составляет 0,113 мкГн, время отклика магнитного зонда равна 2,3 нс. Магнитный зонд был откалиброван с помощью датчика Холла на магнитном поле многослойного соленоида, подключенного к переменному току силой 15 А. Таким образом, погрешность измерения составляет не более 10%. Радиалды сығылу кезеңіндегі плазмалық үдеткіштердің шығысындағы плазмалық ағынның тұрақсыздығы көптеген факторларға байланысты. Олар, өте жылдам, жоғары энергиялы зарядталған бөлшектердің, плазмалық белдіктің өздік магниттік өрісі тудыратын магниттік қысымға қарсы плазманың ішкі қысымының пайда болуы және плазма тығыздығының біртекті таралмауы. Солардың ішінде плазмалық ағынның өздік магниттік өрісін зерттеу ерекше қызығушылық тудырады, себебі ол жоғарыда аталған өзара байланысқан факторлар туралы салыстырмалы түрде ақпарат бере алады.Бұл жұмыста ИПҮ (ҚазҰУ, ЭТФҒЗИ) эксперименттік қондырғыда, атап айтқанда плазмалық үдеткіштің шығысындағы плазмалық ағынның өздік магниттік өрісін өлшеу үшін және зерттеу үшін, жоғары жиілікті, шағын магниттік зонд жасалды. Магниттік зондтың геометриялық өлшемдері келесідей: катушканың диаметрі 2,12 мм, орам саны 7, мыс сымның диаметрі 150 мкм, орамның ұзындығы 1,1 мм. Өлшеуіш катушканың индуктивтілігі 0,113 мкГн, зондтың сезгіштігі 2,3 нс құрайды. Сонымен қатар магниттік зонд шамасы 15 А тең айнымалы ток көзіне қосылған көп қабатты соленоидтың Холл сенсорымен анықталған магниттік өрісінде калибрленді. Калибрлеу нәтижесі көрсеткендей, зондтың өлшеу қателігі 10% аспады.
- 1 June 2021
- Published by al-Farabi Kazakh National University in Recent Contributions to Physics
- Vol. 77 (2) , 30-39
Open AccessMeasuring the self-generated magnetic field and the velocity of plasma flow in a pulsed plasma accelerator
In phase of radial compression the unsteady plasma flow at the exit of a pulsed plasma accelerators is related to the generation of fast high-energy charged particle beams, to plasma density perturbations, to the internal plasma pressure is opposite to the external magnetic pressure (B2/2μ0) associated with plasma column’s self-generated magnetic field. The last one listed above is of particular interest. The investigation of the magnetic field of plasma flow relatively gives information about the above mutually close factors cause to plasma flow instability.In this paper a miniature high-frequency magnetic probe are made for measuring and further investigating the pulsed self-generated magnetic field of plasma flow, in particular, at the exit of the accelerator in an experimental setup of PPA (located in KazNU, IETP). The magnetic probe dimensions are following: coil diameter is 2,12 mm, number of turns is 7, copper wire diameter is 150 μm, and winding length is 1, 1 mm. The coil inductance is about 0,113 μH and the temporal resolution of the magnetic probe is 2,3 ns. The magnetic probe was calibrated using a Hall sensor on the magnetic field of a multi-layered solenoid connected to an alternating power source of 15 A. Thus, the evaluated measurement error of the probe was no more than 10%. Нестабильное течение плазменного сгустка на выходе из плазменных ускорителей в стадии радиального сжатия связано со многими факторами: генерацией высокоэнергичных пучков заряженных частиц, возмущением плотности, внутренним давлением плазмы обратного по направлению внешнему давление собственного магнитного поля плазменного шнура. Особый интерес из них вызывает последнее, исследование собственного магнитного поля плазменного потока, который относительно дает информацию и о вышесказанных взаимосвязанных между собой факторах.В этой работе нами был изготовлен высокочастотный магнитный зонд малого размера для измерения и дальнейшего исследования импульсного магнитного поля плазменного потока в экспериментальной установке ИПУ (КазНУ, НИИЭТФ), в частности на выходе из ускорителя. Магнитный зонд имеет следующие геометрические размеры: диаметр катушки – 2,12 мм, число витков – 7, диаметр медного провода – 150 мкм, длина намотки – 1,1 мм. Индуктивность катушки составляет 0,113 мкГн, время отклика магнитного зонда равна 2,3 нс. Магнитный зонд был откалиброван с помощью датчика Холла на магнитном поле многослойного соленоида, подключенного к переменному току силой 15 А. Таким образом, погрешность измерения составляет не более 10%. Радиалды сығылу кезеңіндегі плазмалық үдеткіштердің шығысындағы плазмалық ағынның тұрақсыздығы көптеген факторларға байланысты. Олар, өте жылдам, жоғары энергиялы зарядталған бөлшектердің, плазмалық белдіктің өздік магниттік өрісі тудыратын магниттік қысымға қарсы плазманың ішкі қысымының пайда болуы және плазма тығыздығының біртекті таралмауы. Солардың ішінде плазмалық ағынның өздік магниттік өрісін зерттеу ерекше қызығушылық тудырады, себебі ол жоғарыда аталған өзара байланысқан факторлар туралы салыстырмалы түрде ақпарат бере алады.Бұл жұмыста ИПҮ (ҚазҰУ, ЭТФҒЗИ) эксперименттік қондырғыда, атап айтқанда плазмалық үдеткіштің шығысындағы плазмалық ағынның өздік магниттік өрісін өлшеу үшін және зерттеу үшін, жоғары жиілікті, шағын магниттік зонд жасалды. Магниттік зондтың геометриялық өлшемдері келесідей: катушканың диаметрі 2,12 мм, орам саны 7, мыс сымның диаметрі 150 мкм, орамның ұзындығы 1,1 мм. Өлшеуіш катушканың индуктивтілігі 0,113 мкГн, зондтың сезгіштігі 2,3 нс құрайды. Сонымен қатар магниттік зонд шамасы 15 А тең айнымалы ток көзіне қосылған көп қабатты соленоидтың Холл сенсорымен анықталған магниттік өрісінде калибрленді. Калибрлеу нәтижесі көрсеткендей, зондтың өлшеу қателігі 10% аспады.
- 26 April 2020
- Published by Pleiades Publishing Ltd in Plasma Physics Reports
- Vol. 46 (4) , 465-471
Generation and Diagnostics of Pulse Plasma Flows
Pulsed plasma accelerators are widely used for the production of high-temperature pulsed plasma flows for fundamental and practical applications. The basic parameters of pulsed plasma accelerators are the characteristics of the external electric and magnetic circuits, as well as the structural and energy properties of the plasma flow. This work aims to characterize an IPU-30 pulsed plasma accelerator. The triple Langmuir probe method, calorimetric plasma energy density measurements, Rogowski coil, and high-speed visible imaging with a Phantom VEO710S fast camera are used to diagnose the pulsed plasma obtained in the IPU-30. The local plasma parameters such as electron temperature and density, the energy density of the pulsed plasma flow, pulsed plasma current, and also discharge current are experimentally obtained at different discharge voltages and air pressure in the chamber. The typical waveforms of the triple probe and Rogowski coil are presented in the form of oscillograms. The images of plasma formation in the discharge gap are obtained and the velocity of a pulsed plasma flow is measured.
- 26 April 2020
- Published by Pleiades Publishing Ltd in Plasma Physics Reports
- Vol. 46 (4) , 465-471
Generation and Diagnostics of Pulse Plasma Flows
Pulsed plasma accelerators are widely used for the production of high-temperature pulsed plasma flows for fundamental and practical applications. The basic parameters of pulsed plasma accelerators are the characteristics of the external electric and magnetic circuits, as well as the structural and energy properties of the plasma flow. This work aims to characterize an IPU-30 pulsed plasma accelerator. The triple Langmuir probe method, calorimetric plasma energy density measurements, Rogowski coil, and high-speed visible imaging with a Phantom VEO710S fast camera are used to diagnose the pulsed plasma obtained in the IPU-30. The local plasma parameters such as electron temperature and density, the energy density of the pulsed plasma flow, pulsed plasma current, and also discharge current are experimentally obtained at different discharge voltages and air pressure in the chamber. The typical waveforms of the triple probe and Rogowski coil are presented in the form of oscillograms. The images of plasma formation in the discharge gap are obtained and the velocity of a pulsed plasma flow is measured.
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (7) , 3047-3051
Experimental Investigation of the Properties of Plasma-Dust Formations on Pulsed Plasma Accelerator
In this paper, we present the results of experimental investigation of the properties of dusty plasma formed in a pulsed plasma accelerator (IPU-30) through the interaction of pulsed plasma beams with a carbon-based target. In the experiments, the interaction of beams of the pulsed plasma with the surface of the carbon plates affords instantaneous heating of the target substrate and subsequent ejection of dust particles from the surface of the plates into the plasma bulk. These dust particles are dragged by the plasma beam creating a moving plasma-dust cloud. A high-speed camera (Phantom VEO710S) is used to obtain the velocity of the dust particles in a beam of the pulsed plasma. Ejection of dust particles is investigated at two different values of the discharge voltage (7 and 12 kV).
- 14 June 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Plasma Science
- Vol. 47 (7) , 3047-3051
Experimental Investigation of the Properties of Plasma-Dust Formations on Pulsed Plasma Accelerator
In this paper, we present the results of experimental investigation of the properties of dusty plasma formed in a pulsed plasma accelerator (IPU-30) through the interaction of pulsed plasma beams with a carbon-based target. In the experiments, the interaction of beams of the pulsed plasma with the surface of the carbon plates affords instantaneous heating of the target substrate and subsequent ejection of dust particles from the surface of the plates into the plasma bulk. These dust particles are dragged by the plasma beam creating a moving plasma-dust cloud. A high-speed camera (Phantom VEO710S) is used to obtain the velocity of the dust particles in a beam of the pulsed plasma. Ejection of dust particles is investigated at two different values of the discharge voltage (7 and 12 kV).
- 4 December 2017
- Published by Cambridge University Press (CUP) in Laser and Particle Beams
- Vol. 35 (4) , 741-749
Investigation of dust formation in fusion reactors by pulsed plasma accelerator
In this paper, the results of an experimental investigation of dust formation in a pulsed plasma accelerator, which is formed due to the interaction of a pulsed plasma flow with the candidate material of the thermonuclear reactor, are presented. Dynamic and optical properties of a pulsed plasma flow are considered. The results of the synergetic analysis by the Raman spectrometer of the target surface after irradiation with plasma are also presented. It was revealed that after interaction with the plasma, the surface of the graphite target becomes amorphous. Materials with fractal surfaces, similar to the materials formed in tokamaks under the action of erosion, were obtained experimentally. Using a high-speed camera Phantom v2512 video shooting of the plasma beam was carried out, during which it was revealed that the pulsed plasma beam has a speed of about 23 km/s.
- 4 December 2017
- Published by Cambridge University Press (CUP) in Laser and Particle Beams
- Vol. 35 (4) , 741-749
Investigation of dust formation in fusion reactors by pulsed plasma accelerator
In this paper, the results of an experimental investigation of dust formation in a pulsed plasma accelerator, which is formed due to the interaction of a pulsed plasma flow with the candidate material of the thermonuclear reactor, are presented. Dynamic and optical properties of a pulsed plasma flow are considered. The results of the synergetic analysis by the Raman spectrometer of the target surface after irradiation with plasma are also presented. It was revealed that after interaction with the plasma, the surface of the graphite target becomes amorphous. Materials with fractal surfaces, similar to the materials formed in tokamaks under the action of erosion, were obtained experimentally. Using a high-speed camera Phantom v2512 video shooting of the plasma beam was carried out, during which it was revealed that the pulsed plasma beam has a speed of about 23 km/s.