Pingyue Song
Pingyue Song has a total of 1 co-authors. Here are the top co-authors by number of shared publications:
- Hossein Hashemi
Ming Hsieh Department of Electrical and Computer Engineering, University of Southern California, Los Angeles, CA, USA
2 shared publications
Latest Publications
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (5) , 1454-1463
mm-Wave Mixer-First Receiver With Selective Passive Wideband Low-Pass Filtering
The front-end of a conventional millimeter-wave receiver (RX) consists of a bandpass filter (BPF) and low-noise amplifier (LNA) prior to the frequency down-conversion mixer. In interference-limited wireless channels, it is more footprint and power efficient to remove the BPF and LNA, and realize the mixer as a “passive” switching scheme. The noise figure of this passive mixer-first RX is improved when numerous such RXs are placed in a phased array or multi-input multi-output (MIMO) configuration. The passive switching mixer can be followed with an on-chip selective passive low-pass filter (LPF) with a small footprint given the large channel bandwidth that is typical in mm-wave applications. In this article, system and circuit design aspects of mm-wave passive mixer-first RXs are discussed and validated by a proof-of-concept 65-nm CMOS prototype. The implemented RX operates in the 21-29-GHz frequency range with 0.5-GHz instantaneous single-sideband (SSB) bandwidth, and achieves stopband to passband rejection of >49 dB, an in-band ICP -1 dB of -6 dBm, and out-of-band B -1 dB > 3.4 dBm.
- 17 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 56 (5) , 1454-1463
mm-Wave Mixer-First Receiver With Selective Passive Wideband Low-Pass Filtering
The front-end of a conventional millimeter-wave receiver (RX) consists of a bandpass filter (BPF) and low-noise amplifier (LNA) prior to the frequency down-conversion mixer. In interference-limited wireless channels, it is more footprint and power efficient to remove the BPF and LNA, and realize the mixer as a “passive” switching scheme. The noise figure of this passive mixer-first RX is improved when numerous such RXs are placed in a phased array or multi-input multi-output (MIMO) configuration. The passive switching mixer can be followed with an on-chip selective passive low-pass filter (LPF) with a small footprint given the large channel bandwidth that is typical in mm-wave applications. In this article, system and circuit design aspects of mm-wave passive mixer-first RXs are discussed and validated by a proof-of-concept 65-nm CMOS prototype. The implemented RX operates in the 21-29-GHz frequency range with 0.5-GHz instantaneous single-sideband (SSB) bandwidth, and achieves stopband to passband rejection of >49 dB, an in-band ICP -1 dB of -6 dBm, and out-of-band B -1 dB > 3.4 dBm.
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (9) , 2475-2486
RF Filter Synthesis Based on Passively Coupled N-Path Resonators
N-path circuits, consisting of an array of switched capacitors driven with non-overlapping clocks, have been used to create radio frequency bandpass and band-stop filters. This paper covers a synthesizing methodology of RF bandpass filters (BPFs) that uses multiple passively coupled N-path resonators to realize a more selective transfer function with transmission zeros. Design details and measurement results of a proof-of-concept filter prototype with a 0.8-1.1-GHz tunable bandpass frequency realized in a 65-nm CMOS technology are presented.
- 4 July 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 54 (9) , 2475-2486
RF Filter Synthesis Based on Passively Coupled N-Path Resonators
N-path circuits, consisting of an array of switched capacitors driven with non-overlapping clocks, have been used to create radio frequency bandpass and band-stop filters. This paper covers a synthesizing methodology of RF bandpass filters (BPFs) that uses multiple passively coupled N-path resonators to realize a more selective transfer function with transmission zeros. Design details and measurement results of a proof-of-concept filter prototype with a 0.8-1.1-GHz tunable bandpass frequency realized in a 65-nm CMOS technology are presented.