ANAbdul Wasim Noori

Abdul Wasim Noori

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Abdul Wasim Noori has a total of 3 co-authors. Here are the top co-authors by number of shared publications:

  • Juma Haydary

    Faculty of Chemical and Food Technology, Slovak University of Technology in Bratislava, Bratislava, Slovak Republic

    2 shared publications
  • Mohammad Jafar Royen

    Institute of Chemical and Environmental Engineering , Slovak University of Technology in Bratislava , Radlinského 9, 81237 Bratislava , Slovakia

    1 shared publication
  • Mohammad Jafar Royen

    Department of Chemical and Biochemical Engineering, Slovak University of Technology in Bratislava, 812 37 Bratislava, Slovakia

    1 shared publication

Latest Publications

  • Open Access

    Experimental Study and Mathematical Modeling of Convective Thin-Layer Drying of Apple Slices

    by Mohammad Jafar Royen, Abdul Wasim Noori, Juma Haydary

    This work represents an experimental study and mathematical modeling of convective apple slice drying. The influence of multiple process parameters such as temperature, air humidity, air velocity and slice thickness on process kinetics, product water activity and parameters of empirical models has been investigated. Drying characteristics of apple slices were monitored at temperatures of 40, 45 and 50 °C, air velocities of 0.6, 0.85 and 1.1 m/s., slice thicknesses of 4, 6, 8, 10 and 12 mm, and in relative air humidity ranges of 25–28, 35–38 and 40–45%. During the process, samples were dried from an initial moisture content of 86.7% to that of 20% (w.b), corresponding to product water activity of 0.45 ± 0.05. By increasing the temperature from 40 to 50 °C, the time for reaching the required product water activity decreased by about 300 min. Sample thickness is the most significant parameter; by increasing the slice thickness from 4 to 12 mm, the time required to achieve the required water activity increased by more than 500 min. For all experimental runs, parameters of five different thin-layer empirical models were estimated. A thin-layer model sensible to process conditions such as temperature, air velocity, layer thickness and air relative humidity was developed and statistically analyzed.


  • Open Access

    An active indirect solar system for food products drying

    by Abdul Wasim Noori, Mohammad Jafar Royen, Juma Haydary

    An energy independent active indirect solar drying system for the study of food products drying at specific climate conditions was developed and tested. As a model material, sliced tomato was selected because of its short shelf live, high humidity and potential to be a high value dried product. Indirect solar dryer enabled complete protection of the dried material against sunlight, birds, insects, rain and dust during the drying process. The solar dryer system design includes a rectangular section (1000 × 600 × 400) mm chamber and a flat solar collector (1500 × 600 × 100) mm with the surface area of 0.9 m 2 . Air flow was induced by a fan installed at the inlet of the collector and powered by a photovoltaic solar panel and a battery system. Temperature and humidity of air were monitored at the collector inlet, collector outlet and the drying chamber outlet. The key element of the collector is a 10.5 m long rectangular section aluminum pipe (55 × 35) mm coated with an absorption layer. The maximum dryer capacity is around 3 kg of wet material (sliced tomato) per batch. Average air temperature increase in the collector was measured to be 30 °C during the winter season. Air relative humidity decreased from 21 % to 15 % after passing through the collector. The moisture of tomato slices decreased from the initial value of 92 % down to 22 % during the time of the experiment (30 h). Quality of tomatoes dried using the designed solar dryer differed significantly in color as well as in texture from those dried by the commonly used methods, like an open sun drying system. Equilibrium moisture content of the product was reached after 30 h in December when the maximum outside temperature was 17.6 °C. The tomato mass decreased from 333 g to 33.15 g; the mass loss being approximately 90 %. The heated air temperature and humidity at the dryer inlet and outlet were influenced by the change of the ambient temperature and humidity during the day. Variation of the drying rate with the change of the ambient temperature and humidity was observed. During summer, when the sun radiation increases, the drying time for sliced tomato with 9 mm thickness decreased from 25 h to 15 h. The sample thickness also has an impact on the drying process. When the sample thickness increased from 9 mm to 12 mm, the drying time increased from 15 h to 20 h of active device time.