Daniel Miek
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Daniel Miek has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
- Michael Höft
Kiel University
15 shared publications - Fynn Kamrath
Chair of Microwave Engineering, Kiel University, Kiel, Germany
10 shared publications - Patrick Boe
Department of Electrical and Information Engineering, Kiel University, Kiel, Germany
9 shared publications Dominik Brouczek
Lithoz GmbH, Vienna, Austria
2 shared publications- Kennet Braasch
Kiel University
2 shared publications - Patrick Boe
Chair of Microwave Engineering, Kiel University, Kiel, Germany
2 shared publications
Latest Publications
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 800-803
Compact Ku-Band Diplexer With Additive Manufactured Multimaterial Dielectric Resonator Insets
This letter presents the design and electrical measurement results of a novel compact diplexer design in Ku-band. The proposed diplexer is based on $\text {TM}_{01\delta }$ mode dielectric resonators (DRs). A fourth-order filter with one triplet section for each channel is used. An additively manufactured inset is used for each filter, which contains the resonators and the required support structure and is printed from two materials in one piece. The chosen arrangement enables a compact design and simple assembly. To validate the concept, the design, fabrication, and measurement of the fourth-order dielectric diplexer are presented.
- 30 April 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (6) , 800-803
Compact Ku-Band Diplexer With Additive Manufactured Multimaterial Dielectric Resonator Insets
This letter presents the design and electrical measurement results of a novel compact diplexer design in Ku-band. The proposed diplexer is based on $\text {TM}_{01\delta }$ mode dielectric resonators (DRs). A fourth-order filter with one triplet section for each channel is used. An additively manufactured inset is used for each filter, which contains the resonators and the required support structure and is printed from two materials in one piece. The chosen arrangement enables a compact design and simple assembly. To validate the concept, the design, fabrication, and measurement of the fourth-order dielectric diplexer are presented.
- Open Access
- 11 January 2025
- Published by Springer Nature in Journal of Infrared, Millimeter, and Terahertz Waves
- Vol. 46 (1) , 1-22
Implementation Methods for Transmission Zeros in Groove Gap Waveguide Filters at W-Band
In this paper, three groove gap waveguide (GGW) filters are presented, which utilize different techniques to create transmission zeros (TZs) in the W-band. First, a fourth-order filter with cross-coupling of non-adjacent cavities realizes five TZs. The filter is implemented using a stacked cavity approach, which simplifies the realization of cross-couplings with positive and negative signs. The source to load cross-coupling realizes one TZ more than predicted from theory. In the second filter, two off-centered posts with partial height are used to realize two TZs. These posts act as strongly frequency-dependent coupling elements and enable the realization of TZs in an inline filter topology. An interdigital-pin implementation has been used since otherwise, the distance between the posts and the sidewalls is too small to allow manufacturing using the Computerized Numerical Control (CNC) milling approach. The third filter is of fourth order and implements two TZs by using a stub-loaded cavity approach. All filters are designed as a proof of concept in the W-band (75–110 GHz) to verify the manufacturability at high-frequency bands. The manufactured components are realized by high-precision CNC milling and measurement results show good agreement with the simulation for all proposed filters.
- 11 January 2025
- Published by Springer Nature in Journal of Infrared, Millimeter, and Terahertz Waves
- Vol. 46 (1) , 1-22
Open AccessImplementation Methods for Transmission Zeros in Groove Gap Waveguide Filters at W-Band
In this paper, three groove gap waveguide (GGW) filters are presented, which utilize different techniques to create transmission zeros (TZs) in the W-band. First, a fourth-order filter with cross-coupling of non-adjacent cavities realizes five TZs. The filter is implemented using a stacked cavity approach, which simplifies the realization of cross-couplings with positive and negative signs. The source to load cross-coupling realizes one TZ more than predicted from theory. In the second filter, two off-centered posts with partial height are used to realize two TZs. These posts act as strongly frequency-dependent coupling elements and enable the realization of TZs in an inline filter topology. An interdigital-pin implementation has been used since otherwise, the distance between the posts and the sidewalls is too small to allow manufacturing using the Computerized Numerical Control (CNC) milling approach. The third filter is of fourth order and implements two TZs by using a stub-loaded cavity approach. All filters are designed as a proof of concept in the W-band (75–110 GHz) to verify the manufacturability at high-frequency bands. The manufactured components are realized by high-precision CNC milling and measurement results show good agreement with the simulation for all proposed filters.
- 18 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (6) , 721-724
3-D Screen Printing: Efficient Additive Manufacturing of Groove Gap Waveguide Filters in D-Band
In this letter, the design and additive manufacturing (AM) of a groove gap waveguide (GGW) filter in the $D$ -band is presented. For this kind of filter, the manufacturing of very small periodic pin structures is necessary. The conventional manufacturing of these structures by CNC milling is time-consuming, and high-precision milling machines are extremely expensive. Other manufacturing processes such as screen printing are, therefore, required for the cost-effective and efficient production of large quantities. The screen printing process is presented, and its suitability for the production of GGW components in the millimeter-wave area is validated by a third-order bandpass filter prototype in $D$ -band, which was manufactured and electrically characterized.
- 18 April 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 34 (6) , 721-724
3-D Screen Printing: Efficient Additive Manufacturing of Groove Gap Waveguide Filters in D-Band
In this letter, the design and additive manufacturing (AM) of a groove gap waveguide (GGW) filter in the $D$ -band is presented. For this kind of filter, the manufacturing of very small periodic pin structures is necessary. The conventional manufacturing of these structures by CNC milling is time-consuming, and high-precision milling machines are extremely expensive. Other manufacturing processes such as screen printing are, therefore, required for the cost-effective and efficient production of large quantities. The screen printing process is presented, and its suitability for the production of GGW components in the millimeter-wave area is validated by a third-order bandpass filter prototype in $D$ -band, which was manufactured and electrically characterized.
- Open Access
- 19 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 70-83
Quasi-Elliptical Stub-Based Multi-Resonance Waveguide Filters With Low Manufacturing Complexity for mm-Wave Applications
In this paper, the design and realization of quasi-elliptical waveguide filters with reduced manufacturing complexity are discussed. The filters are based on TE mode cavities, which are loaded with TM mode stubs. It is shown that dual-, triple- and quadruple-resonance segments are obtained by using up to three stubs loaded on the broad side of a TE mode cavity. The structures obtained can either be used as a stand-alone filter or even as a building block suitable for the realization of higher order filters. The multi-resonance blocks reveal several advantages in the mm-wave area: The manufacturing complexity is easy to handle and comparable to simple all-pole filters, which is especially important at high frequencies. Therefore, three prototypes are manufactured as proof of concept in the D-band (110 GHz–170 GHz). Moreover, the building blocks are able to produce $n-1$ transmission zeros (TZs) with $n$ being the number of resonances. Therefore, the blocks generate between one (dual-resonance) and up to three (quadruple-resonance) TZs. Advantageously, the filters can be cut in the E-plane in order to reduce the insertion loss and hence consist of only two components. Three examples are manufactured by high precision CNC milling and reveal good agreement to the simulation by obtaining unloaded Q-factors of up to 1000.
- 19 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 70-83
Open AccessQuasi-Elliptical Stub-Based Multi-Resonance Waveguide Filters With Low Manufacturing Complexity for mm-Wave Applications
In this paper, the design and realization of quasi-elliptical waveguide filters with reduced manufacturing complexity are discussed. The filters are based on TE mode cavities, which are loaded with TM mode stubs. It is shown that dual-, triple- and quadruple-resonance segments are obtained by using up to three stubs loaded on the broad side of a TE mode cavity. The structures obtained can either be used as a stand-alone filter or even as a building block suitable for the realization of higher order filters. The multi-resonance blocks reveal several advantages in the mm-wave area: The manufacturing complexity is easy to handle and comparable to simple all-pole filters, which is especially important at high frequencies. Therefore, three prototypes are manufactured as proof of concept in the D-band (110 GHz–170 GHz). Moreover, the building blocks are able to produce $n-1$ transmission zeros (TZs) with $n$ being the number of resonances. Therefore, the blocks generate between one (dual-resonance) and up to three (quadruple-resonance) TZs. Advantageously, the filters can be cut in the E-plane in order to reduce the insertion loss and hence consist of only two components. Three examples are manufactured by high precision CNC milling and reveal good agreement to the simulation by obtaining unloaded Q-factors of up to 1000.
- Open Access
- 16 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 84-95
Dielectric TM-Mode Y-Shaped Doublet Structure
This paper discusses dielectric TM-mode filters based on high permittivity Y-shaped ceramics. It is shown that this type of ceramic operates as a dual-mode resonator and therefore contributes two reflection zeros as well as one transmission zero (TZ) to the filter response. Hence, it can be interpreted as a doublet structure and used for the realization of quasi-elliptical filter responses of different order. The dual-mode resonator can be used in multiple different filter set-ups: On the one hand, a combination with classical TM $_{010}$ -mode resonators is possible to allow the realization of TZs in an in-line filter configuration without using cross-coupling apertures. Therefore, negative or diagonal cross-couplings, which are often difficult to realize and handle, can be avoided. On the other hand, several Y-shaped ceramics can be coupled directly with each other to increase the number of TZs to $n_{fz}=n/2$ , where $n$ is the order of the filter. Finally, it is shown that even a combination with extracted pole elements is realizable. Prototypes based on modular segments are manufactured as proof of concept.
- 16 December 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 3 (1) , 84-95
Open AccessDielectric TM-Mode Y-Shaped Doublet Structure
This paper discusses dielectric TM-mode filters based on high permittivity Y-shaped ceramics. It is shown that this type of ceramic operates as a dual-mode resonator and therefore contributes two reflection zeros as well as one transmission zero (TZ) to the filter response. Hence, it can be interpreted as a doublet structure and used for the realization of quasi-elliptical filter responses of different order. The dual-mode resonator can be used in multiple different filter set-ups: On the one hand, a combination with classical TM $_{010}$ -mode resonators is possible to allow the realization of TZs in an in-line filter configuration without using cross-coupling apertures. Therefore, negative or diagonal cross-couplings, which are often difficult to realize and handle, can be avoided. On the other hand, several Y-shaped ceramics can be coupled directly with each other to increase the number of TZs to $n_{fz}=n/2$ , where $n$ is the order of the filter. Finally, it is shown that even a combination with extracted pole elements is realizable. Prototypes based on modular segments are manufactured as proof of concept.
- Open Access
- 16 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (3) , 496-506
Ceramic Additive Manufactured Monolithic X-Shaped TM Dual-Mode Filter
This paper presents a monolithic 3D-printed ceramic X-shaped dual-mode microwave filter. The filter is manufactured utilizing a lithography-based ceramic manufacturing (LCM) process, allowing the realization of the resonator as well as the housing in one single piece. Therefore, contact as well as alignment problems, usually arising between a ceramic in $TM$ mode operation and a metallic enclosure, can conveniently be avoided. A fourth order dual-mode filter with a designed center frequency of 6 GHz and a bandwidth of 279 MHz is realized in alumina material. Practical design rules to be considered in the filter layout process as well as limitations imposed by the LCM approach are discussed. The outer surface of the ceramic cavity is subsequently metallized using a silver spray-coating. Advantageously, the metallization is only a few micrometers thick, wherefore the weight of the component can be reduced. The measurement results are compared to the simulation and reveal good agreement. A temperature stability measurement shows a center frequency downward shift of 0.22%.
- 16 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (3) , 496-506
Open AccessCeramic Additive Manufactured Monolithic X-Shaped TM Dual-Mode Filter
This paper presents a monolithic 3D-printed ceramic X-shaped dual-mode microwave filter. The filter is manufactured utilizing a lithography-based ceramic manufacturing (LCM) process, allowing the realization of the resonator as well as the housing in one single piece. Therefore, contact as well as alignment problems, usually arising between a ceramic in $TM$ mode operation and a metallic enclosure, can conveniently be avoided. A fourth order dual-mode filter with a designed center frequency of 6 GHz and a bandwidth of 279 MHz is realized in alumina material. Practical design rules to be considered in the filter layout process as well as limitations imposed by the LCM approach are discussed. The outer surface of the ceramic cavity is subsequently metallized using a silver spray-coating. Advantageously, the metallization is only a few micrometers thick, wherefore the weight of the component can be reduced. The measurement results are compared to the simulation and reveal good agreement. A temperature stability measurement shows a center frequency downward shift of 0.22%.
- Open Access
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 134-144
Bandwidth and Center Frequency Reconfigurable Waveguide Filter Based on Liquid Crystal Technology
This paper presents for the first time a fully electronically reconfigurable waveguide filter tunable in bandwidth and center frequency based on liquid crystal (LC) technology. A continuously reconfigurable two pole bandpass filter is designed and characterized in the Ka-band at $30 \,\mathrm{GHz}$ . To be able to tune both center frequency and bandwidth independently, the resonators and coupling structures are filled with LC as tunable material. Hence, the filter’s center frequency and coupling strengths can be tuned and, furthermore, tuning with constant filter characteristic is possible. To tune the LC, a novel two-layer electrode design for waveguide structures is presented, which is simple to integrate and provides a high tuning efficiency with low insertion loss. By applying different bias configurations, the LC’s effective permittivity can be varied, and therefore, also the resonators’ electrical lengths. The presented two pole filter can adapt its center frequency from $29.8 \,\mathrm{GHz}\,{\rm to}\, 30.7 \,\mathrm{GHz}$ with a maximum $3 \,{\rm dB}$ bandwidth variation from $660 \,\mathrm{MHz}\,{\rm to}\, 870 \,\mathrm{MHz}$ . The measurements are carried out with bias voltages up to $\pm$ $250 \,\mathrm{V}$ .
- 27 October 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 2 (1) , 134-144
Open AccessBandwidth and Center Frequency Reconfigurable Waveguide Filter Based on Liquid Crystal Technology
This paper presents for the first time a fully electronically reconfigurable waveguide filter tunable in bandwidth and center frequency based on liquid crystal (LC) technology. A continuously reconfigurable two pole bandpass filter is designed and characterized in the Ka-band at $30 \,\mathrm{GHz}$ . To be able to tune both center frequency and bandwidth independently, the resonators and coupling structures are filled with LC as tunable material. Hence, the filter’s center frequency and coupling strengths can be tuned and, furthermore, tuning with constant filter characteristic is possible. To tune the LC, a novel two-layer electrode design for waveguide structures is presented, which is simple to integrate and provides a high tuning efficiency with low insertion loss. By applying different bias configurations, the LC’s effective permittivity can be varied, and therefore, also the resonators’ electrical lengths. The presented two pole filter can adapt its center frequency from $29.8 \,\mathrm{GHz}\,{\rm to}\, 30.7 \,\mathrm{GHz}$ with a maximum $3 \,{\rm dB}$ bandwidth variation from $660 \,\mathrm{MHz}\,{\rm to}\, 870 \,\mathrm{MHz}$ . The measurements are carried out with bias voltages up to $\pm$ $250 \,\mathrm{V}$ .
- Open Access
- 16 June 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 14 (3) , 369-378
Investigation of the cutting plane and tolerance analysis of cross-coupled W-band waveguide filters with multiple transmission zeros by source to load cross-coupling
In this paper, the influence of the cutting plane as well as the orientation of the cavities in cross-coupled W-band waveguide filters are investigated. When waveguide filters are manufactured with the commonly known CNC (computer numerical control) milling technique, at least one cutting plane is required. The position of this cutting plane has an impact on the composition of the cavities, the manufacturing accuracy, and on the maximal number of transmission zeros (TZs) introduced by a direct source to load (SL) cross-coupling. Similar filter set-ups therefore may show different performances depending on the position of this cutting plane. To examine all these effects, three similar fourth-order W-band filter set-ups are realized with distinct cutting planes and different oriented cavities. The filters are compared in terms of the sensitivity to manufacturing tolerances, the maximal number of TZs introduced by a direct SL cross-coupling as well as their spurious mode performance.
- 16 June 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 14 (3) , 369-378
Open AccessInvestigation of the cutting plane and tolerance analysis of cross-coupled W-band waveguide filters with multiple transmission zeros by source to load cross-coupling
In this paper, the influence of the cutting plane as well as the orientation of the cavities in cross-coupled W-band waveguide filters are investigated. When waveguide filters are manufactured with the commonly known CNC (computer numerical control) milling technique, at least one cutting plane is required. The position of this cutting plane has an impact on the composition of the cavities, the manufacturing accuracy, and on the maximal number of transmission zeros (TZs) introduced by a direct source to load (SL) cross-coupling. Similar filter set-ups therefore may show different performances depending on the position of this cutting plane. To examine all these effects, three similar fourth-order W-band filter set-ups are realized with distinct cutting planes and different oriented cavities. The filters are compared in terms of the sensitivity to manufacturing tolerances, the maximal number of TZs introduced by a direct SL cross-coupling as well as their spurious mode performance.
- Open Access
- 24 March 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 14 (3) , 397-406
Modular waveguide filter platform for educational and prototyping purposes
In this paper, a modular waveguide filter platform suitable for educational and prototyping purposes is presented. The waveguide filter platform is dimensioned to work in the F-band (4.9–7.05 GHz). The design of the platform is discussed and versatile application possibilities are shown in many examples. The platform can be used to realize generalized Chebyshev filters with or without cross-couplings by exploiting TE101 and TE102 mode cavities. Transmission zeros can be introduced by the utilization of wires or aperture couplings. Filter topologies based on the extracted pole technique can be examined as well. Small changes in the set-up also allow the realization of a gap waveguide filter, a diplexer set-up as well as filters with frequency-dependent coupling apertures. Most required components can either be purchased cheaply or be manufactured with a three-dimensional printer.
- 24 March 2021
- Published by Cambridge University Press (CUP) in International Journal of Microwave and Wireless Technologies
- Vol. 14 (3) , 397-406
Open AccessModular waveguide filter platform for educational and prototyping purposes
In this paper, a modular waveguide filter platform suitable for educational and prototyping purposes is presented. The waveguide filter platform is dimensioned to work in the F-band (4.9–7.05 GHz). The design of the platform is discussed and versatile application possibilities are shown in many examples. The platform can be used to realize generalized Chebyshev filters with or without cross-couplings by exploiting TE101 and TE102 mode cavities. Transmission zeros can be introduced by the utilization of wires or aperture couplings. Filter topologies based on the extracted pole technique can be examined as well. Small changes in the set-up also allow the realization of a gap waveguide filter, a diplexer set-up as well as filters with frequency-dependent coupling apertures. Most required components can either be purchased cheaply or be manufactured with a three-dimensional printer.
- 12 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 555-558
Hybrid Inline TE/TM Mode Dielectric Resonator Filters with Wide Spurious Free Range and Controllable Transmission Zeros
In this paper a third order dielectric hybrid bandpass filter based on TE and TM mode ceramics is presented. The dominant TE 01δ and TM 010 modes are utilized to design the passband. A TM mode dielectric resonator (DR) is used to suppress the spurious modes of the TE mode DRs while the TE mode DRs are used together with the input/output couplings to create two independently controllable transmission zeros by exciting higher order modes (HOM). To validate the approach, the designed filter is manufactured and its measurement results are compared with the simulation results. A suitable filter topology and coupling matrix are derived and discussed.
- 12 January 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 555-558
Hybrid Inline TE/TM Mode Dielectric Resonator Filters with Wide Spurious Free Range and Controllable Transmission Zeros
In this paper a third order dielectric hybrid bandpass filter based on TE and TM mode ceramics is presented. The dominant TE 01δ and TM 010 modes are utilized to design the passband. A TM mode dielectric resonator (DR) is used to suppress the spurious modes of the TE mode DRs while the TE mode DRs are used together with the input/output couplings to create two independently controllable transmission zeros by exciting higher order modes (HOM). To validate the approach, the designed filter is manufactured and its measurement results are compared with the simulation results. A suitable filter topology and coupling matrix are derived and discussed.