Simone Santucci
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Simone Santucci has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Vincenzo Esposito
Technical University of Denmark
8 shared publications Haiwu Zhang
Department of Energy Conversion and Storage, Technical University of Denmark, Lyngby, Denmark
4 shared publications- Ivano Eligio Castelli
Department of Energy Conversion and Storage, Technical University of Denmark, Kongens Lyngby, Denmark
4 shared publications - Nini Pryds
Technical University of Denmark
4 shared publications - Simone Sanna
Department of Energy Conversion and Storage, Technical University of Denmark, DK-4000 Roskilde, Denmark
4 shared publications - Ahsanul Kabir
Gdansk Univ Technol, Fac Elect Telecommun & Informat, Gabriela Narutowicza 11-12, PL-80233 Gdansk, Poland
2 shared publications
Latest Publications
- 12 November 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (6)
Growth dynamics in patterned TiO2 deposited by direct atomic layer processing (DALP) in ambient conditions
Area-selective atomic layer deposition (AS-ALD) is a nanofabrication method delivering atomic layers of patterned films with exceptional precision, but it still relies on vacuum hardware and surface chemistry pretreatments that limit flexibility and throughput. Direct atomic layer processing (DALP) is an ALD-based technique that allows the deposition of single atomic layers in an additive fashion through a micronozzle, with no requirements for vacuum. In this work, we demonstrate DALP deposition of line-patterned TiO2 2–18 nm thin films deposited at temperatures from 80 to 250 °C. We show that the films were locally deposited, with no overspray, with a surface uniformity of 0.03 ± 0.01 nm, and a roughness in the range of 0.23 ± 0.09 nm (80 °C) to 0.57 ± 0.05 nm (250 °C). Moreover, we find that the films undergo a transient growth regime at a low number of cycles, with low nucleation delay (0–11 cycles) and a rapid growth relaxation with decay time-constants τ from 18 to 32 cycles, depending on the temperature. A linear growth regime is achieved after ≈3τ, with values from 0.033 ± 0.001 (250 °C) to 0.052 ± 0.003 (80 °C) nm/cycle. These results show that DALP produces ALD quality TiO2 at ambient pressure and line speeds up to 200 mm/s, providing a high-throughput alternative to inhibitor-based AS-ALD.
- 12 November 2025
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 43 (6)
Growth dynamics in patterned TiO2 deposited by direct atomic layer processing (DALP) in ambient conditions
Area-selective atomic layer deposition (AS-ALD) is a nanofabrication method delivering atomic layers of patterned films with exceptional precision, but it still relies on vacuum hardware and surface chemistry pretreatments that limit flexibility and throughput. Direct atomic layer processing (DALP) is an ALD-based technique that allows the deposition of single atomic layers in an additive fashion through a micronozzle, with no requirements for vacuum. In this work, we demonstrate DALP deposition of line-patterned TiO2 2–18 nm thin films deposited at temperatures from 80 to 250 °C. We show that the films were locally deposited, with no overspray, with a surface uniformity of 0.03 ± 0.01 nm, and a roughness in the range of 0.23 ± 0.09 nm (80 °C) to 0.57 ± 0.05 nm (250 °C). Moreover, we find that the films undergo a transient growth regime at a low number of cycles, with low nucleation delay (0–11 cycles) and a rapid growth relaxation with decay time-constants τ from 18 to 32 cycles, depending on the temperature. A linear growth regime is achieved after ≈3τ, with values from 0.033 ± 0.001 (250 °C) to 0.052 ± 0.003 (80 °C) nm/cycle. These results show that DALP produces ALD quality TiO2 at ambient pressure and line speeds up to 200 mm/s, providing a high-throughput alternative to inhibitor-based AS-ALD.
- Open Access
- 2 January 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-11
Enhanced non-classical electrostriction in strained tetragonal ceria
Electrostriction is the upsurge of strain under an electric field in any dielectric material. Oxygen-defective metal oxides, such as acceptor-doped ceria, exhibit high electrostriction 10-17 m2V-2 values, which can be further enhanced via interface engineering at the nanoscale. This effect in ceria is “non-classical” as it arises from an intricate relation between defect-induced polarisation and local elastic distortion in the lattice. Here, we investigate the impact of mismatch strain when epitaxial Gd-doped CeO2 thin films are grown on various single-crystal substrates. We demonstrate that varying the compressive and tensile strain can fine-tune the electromechanical response. The electrostriction coefficients achieve a large M11 ≈ 3.6·10-15 m2V-2 in lattices of in-plane compressed films, i.e., a positive tetragonality (c/a-1 > 0), with stress above 3 GPa at the film/substrate interface. Chemical and structural analysis suggests that the high electrostriction stems from anisotropic distortions in the local lattice strain, which lead to constructively oriented elastic dipoles and Ce3+ electronic defects.
- 2 January 2025
- Published by Springer Nature in Nature Communications
- Vol. 16 (1) , 1-11
Open AccessEnhanced non-classical electrostriction in strained tetragonal ceria
Electrostriction is the upsurge of strain under an electric field in any dielectric material. Oxygen-defective metal oxides, such as acceptor-doped ceria, exhibit high electrostriction 10-17 m2V-2 values, which can be further enhanced via interface engineering at the nanoscale. This effect in ceria is “non-classical” as it arises from an intricate relation between defect-induced polarisation and local elastic distortion in the lattice. Here, we investigate the impact of mismatch strain when epitaxial Gd-doped CeO2 thin films are grown on various single-crystal substrates. We demonstrate that varying the compressive and tensile strain can fine-tune the electromechanical response. The electrostriction coefficients achieve a large M11 ≈ 3.6·10-15 m2V-2 in lattices of in-plane compressed films, i.e., a positive tetragonality (c/a-1 > 0), with stress above 3 GPa at the film/substrate interface. Chemical and structural analysis suggests that the high electrostriction stems from anisotropic distortions in the local lattice strain, which lead to constructively oriented elastic dipoles and Ce3+ electronic defects.
- 18 March 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (15) , 9173-9183
Non-classical electrostriction in calcium-doped cerium oxide ceramics
Oxygen-defective metal oxides, e.g., acceptor-doped CeO2, demonstrate exceptionally large electrostrictive responses compared to state-of-the-art electromechanically active ceramic materials.
- 18 March 2024
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 12 (15) , 9173-9183
Non-classical electrostriction in calcium-doped cerium oxide ceramics
Oxygen-defective metal oxides, e.g., acceptor-doped CeO2, demonstrate exceptionally large electrostrictive responses compared to state-of-the-art electromechanically active ceramic materials.
- 21 September 2022
- Published by Springer Nature in Nature
- Vol. 609 (7928) , 695-700
Atomically engineered interfaces yield extraordinary electrostriction
Electrostriction is a property of dielectric materials whereby an applied electric field induces a mechanical deformation proportional to the square of that field. The magnitude of the effect is usually minuscule (–19 m2 V–2 for simple oxides). However, symmetry-breaking phenomena at the interfaces can offer an efficient strategy for the design of new properties1,2. Here we report an engineered electrostrictive effect via the epitaxial deposition of alternating layers of Gd2O3-doped CeO2 and Er2O3-stabilized δ-Bi2O3 with atomically controlled interfaces on NdGaO3 substrates. The value of the electrostriction coefficient achieved is 2.38 × 10–14 m2 V–2, exceeding the best known relaxor ferroelectrics by three orders of magnitude. Our theoretical calculations indicate that this greatly enhanced electrostriction arises from coherent strain imparted by interfacial lattice discontinuity. These artificial heterostructures open a new avenue for the design and manipulation of electrostrictive materials and devices for nano/micro actuation and cutting-edge sensors.
- 21 September 2022
- Published by Springer Nature in Nature
- Vol. 609 (7928) , 695-700
Atomically engineered interfaces yield extraordinary electrostriction
Electrostriction is a property of dielectric materials whereby an applied electric field induces a mechanical deformation proportional to the square of that field. The magnitude of the effect is usually minuscule (–19 m2 V–2 for simple oxides). However, symmetry-breaking phenomena at the interfaces can offer an efficient strategy for the design of new properties1,2. Here we report an engineered electrostrictive effect via the epitaxial deposition of alternating layers of Gd2O3-doped CeO2 and Er2O3-stabilized δ-Bi2O3 with atomically controlled interfaces on NdGaO3 substrates. The value of the electrostriction coefficient achieved is 2.38 × 10–14 m2 V–2, exceeding the best known relaxor ferroelectrics by three orders of magnitude. Our theoretical calculations indicate that this greatly enhanced electrostriction arises from coherent strain imparted by interfacial lattice discontinuity. These artificial heterostructures open a new avenue for the design and manipulation of electrostrictive materials and devices for nano/micro actuation and cutting-edge sensors.
- 25 January 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (8) , 4024-4031
Enhanced electromechanical properties in low-temperature gadolinium-doped ceria composites with low-dimensional carbon allotropes
A new functional carbon–metal oxide hybrid is designed and fabricated by field-assisted sintering—the hybrid material results in enhanced electro-chemo-mechanical properties with high crystallinity, facile fabrication method, and cost-efficiency.
- 25 January 2022
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 10 (8) , 4024-4031
Enhanced electromechanical properties in low-temperature gadolinium-doped ceria composites with low-dimensional carbon allotropes
A new functional carbon–metal oxide hybrid is designed and fabricated by field-assisted sintering—the hybrid material results in enhanced electro-chemo-mechanical properties with high crystallinity, facile fabrication method, and cost-efficiency.
- Open Access
- 20 April 2021
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 23 (19) , 11233-11239
Electromechanically active pair dynamics in a Gd-doped ceria single crystal
Oxygen-defective ceria, e.g. Gd-doped ceria, shows giant electromechanical properties related to a complex local rearrangement of its lattice. Although they are not entirely identified, the electroactive mechanisms arise from cation and oxygen vacancy (VO) pairs (i.e. Ce–VO), and the local structural elastic distortion in their surroundings. Here, we study the geometry and behaviour of Ce–VO pairs in a grain boundary-free bulk Ce0.9Gd0.1O1.95 single crystal under an AC electric field of ca. 11 kV cm−1. The analysis was carried out through X-ray absorption spectroscopy (XAS) techniques at the Ce L-III edge. Using Density Functional Theory (DFT) calculations, we investigated the effects of the strain on density of states and orbitals at the valence band edge. Our research indicates that electrostriction increases at low temperatures. The electromechanical strain has a structural nature and can rise by one order of magnitude, i.e., from 5 × 10−4 at room temperature to 5 × 10−3 at −193 °C, due to an increase in the population of the electrically active pairs. At a constant VO concentration, the material can thus configure heterogeneous pairs and elastic nanodomains that are either mechanically responsive or not.
- 20 April 2021
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 23 (19) , 11233-11239
Open AccessElectromechanically active pair dynamics in a Gd-doped ceria single crystal
Oxygen-defective ceria, e.g. Gd-doped ceria, shows giant electromechanical properties related to a complex local rearrangement of its lattice. Although they are not entirely identified, the electroactive mechanisms arise from cation and oxygen vacancy (VO) pairs (i.e. Ce–VO), and the local structural elastic distortion in their surroundings. Here, we study the geometry and behaviour of Ce–VO pairs in a grain boundary-free bulk Ce0.9Gd0.1O1.95 single crystal under an AC electric field of ca. 11 kV cm−1. The analysis was carried out through X-ray absorption spectroscopy (XAS) techniques at the Ce L-III edge. Using Density Functional Theory (DFT) calculations, we investigated the effects of the strain on density of states and orbitals at the valence band edge. Our research indicates that electrostriction increases at low temperatures. The electromechanical strain has a structural nature and can rise by one order of magnitude, i.e., from 5 × 10−4 at room temperature to 5 × 10−3 at −193 °C, due to an increase in the population of the electrically active pairs. At a constant VO concentration, the material can thus configure heterogeneous pairs and elastic nanodomains that are either mechanically responsive or not.
- 1 September 2020
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 22 (38) , 21900-21908
Atomic-scale insights into electro-steric substitutional chemistry of cerium oxide
Atomic-scale simulations identify the substitutional chemistry of cerium oxide beyond the trivalent, rare-earth cations.
- 1 September 2020
- Published by Royal Society of Chemistry (RSC) in Physical Chemistry Chemical Physics
- Vol. 22 (38) , 21900-21908
Atomic-scale insights into electro-steric substitutional chemistry of cerium oxide
Atomic-scale simulations identify the substitutional chemistry of cerium oxide beyond the trivalent, rare-earth cations.
- Open Access
- 30 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (28) , 14023-14030
Electro-chemo-mechanical effect in Gd-doped ceria thin films with a controlled orientation
Enhanced Gd-doped ceria electrostriction: This study uncovers new anisotropic properties in thin films, enhancing the effect along with the 〈100〉 directions by one order of magnitude and proposing a new microscopic model to explain such findings.
- 30 June 2020
- Published by Royal Society of Chemistry (RSC) in Journal of Materials Chemistry A
- Vol. 8 (28) , 14023-14030
Open AccessElectro-chemo-mechanical effect in Gd-doped ceria thin films with a controlled orientation
Enhanced Gd-doped ceria electrostriction: This study uncovers new anisotropic properties in thin films, enhancing the effect along with the 〈100〉 directions by one order of magnitude and proposing a new microscopic model to explain such findings.
- Open Access
- 1 July 2019
- Published by AIP Publishing in APL Materials
- Vol. 7 (7) , 071104
Enhanced electro-mechanical coupling of TiN/Ce0.8Gd0.2O1.9 thin film electrostrictor
Gadolium doped ceria, Gd:CeO2 (CGO), have recently been shown to possess an exceptional high electrostriction coefficient (Q), which is at the least three orders of magnitude larger than the best performing lead-based electrostrictors, e.g. Pb(Mn1/3Nb2/3)O3. Herein, we show that CGO thin films fabricated by a pulsed laser deposition method can be directly integrated onto the Si substrate by using TiN films of few nanometers as functional electrodes. The exceptional good coupling between TiN and Ce0.8Gd0.2O1.9 yields a high electrostriction coefficient of Qe = 40 m4 C−2 and a superior electrochemomechanical stability with respect to the metal electrodes.
- 1 July 2019
- Published by AIP Publishing in APL Materials
- Vol. 7 (7) , 071104
Open AccessEnhanced electro-mechanical coupling of TiN/Ce0.8Gd0.2O1.9 thin film electrostrictor
Gadolium doped ceria, Gd:CeO2 (CGO), have recently been shown to possess an exceptional high electrostriction coefficient (Q), which is at the least three orders of magnitude larger than the best performing lead-based electrostrictors, e.g. Pb(Mn1/3Nb2/3)O3. Herein, we show that CGO thin films fabricated by a pulsed laser deposition method can be directly integrated onto the Si substrate by using TiN films of few nanometers as functional electrodes. The exceptional good coupling between TiN and Ce0.8Gd0.2O1.9 yields a high electrostriction coefficient of Qe = 40 m4 C−2 and a superior electrochemomechanical stability with respect to the metal electrodes.