Xianhu Luo
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Xianhu Luo has a total of 43 co-authors. Here are the top co-authors by number of shared publications:
- Xu Cheng
Microsystem and Terahertz Research Center, China Academy of Engineering Physics, Chengdu, China
10 shared publications - Jiang-An Han
Microsystem and Terahertz Research Center, China Academy of Engineering Physics, Chengdu, China
6 shared publications - Fengjun Chen
Microsystem and Terahertz Research Center, China Academy of Engineering Physics, Chengdu, China
4 shared publications Liang Zhang
Microsystem and Terahertz Research Center, Institute of Electronic Engineering, China Academy of Engineering Physics, Mianyang, China
4 shared publications- Xinlin Xia
School of Microelectronics, South China University of Technology, Guangzhou, CHINA
4 shared publications Xianjin Deng
Microsystem and Terahertz Research Center, Institute of Electronic Engineering, China Academy of Engineering Physics, Mianyang, China
3 shared publications
Latest Publications
- 25 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1486-1489
Miniature Wideband Superconducting Filter Design With Four Transmission Zeros Based on Quintuple-Mode Resonator (QMR)
This letter presents a high-temperature superconducting (HTS) wideband bandpass filter (BPF) based on quintuple-mode resonator (QMR). The connected resonator method (CRM) is employed to efficiently construct the multimode resonator. The proposed QMR generates two odd-mode frequencies and three even-mode frequencies, which collectively form the filter’s passband. To validate the proposed approach, one- and two-stage wideband filters are designed based on the QMR. Additionally, four transmission zeros (TZs) are strategically placed on both sides of the passband, significantly improving selectivity. By adjusting the geometrical parameters, these TZs can be controlled. The proposed wideband filter operates at 6.31 GHz with a fractional bandwidth (FBW) of approximately 78.3%. Measured results demonstrate excellent agreement with simulations, confirming the effectiveness of the design.
- 25 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (10) , 1486-1489
Miniature Wideband Superconducting Filter Design With Four Transmission Zeros Based on Quintuple-Mode Resonator (QMR)
This letter presents a high-temperature superconducting (HTS) wideband bandpass filter (BPF) based on quintuple-mode resonator (QMR). The connected resonator method (CRM) is employed to efficiently construct the multimode resonator. The proposed QMR generates two odd-mode frequencies and three even-mode frequencies, which collectively form the filter’s passband. To validate the proposed approach, one- and two-stage wideband filters are designed based on the QMR. Additionally, four transmission zeros (TZs) are strategically placed on both sides of the passband, significantly improving selectivity. By adjusting the geometrical parameters, these TZs can be controlled. The proposed wideband filter operates at 6.31 GHz with a fractional bandwidth (FBW) of approximately 78.3%. Measured results demonstrate excellent agreement with simulations, confirming the effectiveness of the design.
- 7 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (3) , 314-317
A D-Band ×8 Frequency Multiplier With Harmonic Suppression Enhancements in SiGe BiCMOS
In this letter, a D -band frequency octupler ( $\times$ 8) with high harmonic suppression is presented in a 0.13- $\mu$ m SiGe BiCMOS technology. To enhance the suppression of even harmonics among high harmonics, we have implemented and refined a waveform shaping technique that effectively elevates the second harmonic while suppressing the fourth, sixth, and higher even harmonics. Additionally, the transformer-based bandpass filters (BPFs) are integrated into the design of the $\times$ 8 frequency multiplier to enhance the suppression of nontarget frequency signals without compromising power consumption. To validate our proposed concept, a D -band $\times$ 8 frequency multiplier operating at 114.5–140 GHz is manufactured in a SiGe process. The circuit achieved an output power of $-$ 2.5 dBm with an input power of $-$ 2 dBm. Within the 3-dB bandwidth, the suppression of various harmonics exceeded 28 dBc and with the maximum suppression exceeding 38 dBc. The chip consumed 125 mW of power and occupied an area of 0.63 $\times$ 1.2 mm $^{2}$ .
- 7 January 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Technology Letters
- Vol. 35 (3) , 314-317
A D-Band ×8 Frequency Multiplier With Harmonic Suppression Enhancements in SiGe BiCMOS
In this letter, a D -band frequency octupler ( $\times$ 8) with high harmonic suppression is presented in a 0.13- $\mu$ m SiGe BiCMOS technology. To enhance the suppression of even harmonics among high harmonics, we have implemented and refined a waveform shaping technique that effectively elevates the second harmonic while suppressing the fourth, sixth, and higher even harmonics. Additionally, the transformer-based bandpass filters (BPFs) are integrated into the design of the $\times$ 8 frequency multiplier to enhance the suppression of nontarget frequency signals without compromising power consumption. To validate our proposed concept, a D -band $\times$ 8 frequency multiplier operating at 114.5–140 GHz is manufactured in a SiGe process. The circuit achieved an output power of $-$ 2.5 dBm with an input power of $-$ 2 dBm. Within the 3-dB bandwidth, the suppression of various harmonics exceeded 28 dBc and with the maximum suppression exceeding 38 dBc. The chip consumed 125 mW of power and occupied an area of 0.63 $\times$ 1.2 mm $^{2}$ .
- 16 November 2024
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 189
Miniaturized millimeter-wave dual-band band-pass on-chip filter in 0.13-μm SiGe BiCMOS
- 16 November 2024
- Published by Elsevier in AEU - International Journal of Electronics and Communications
- Vol. 189
Miniaturized millimeter-wave dual-band band-pass on-chip filter in 0.13-μm SiGe BiCMOS
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 86-89
Compact Multifunctional 180° Hybrid-Based 300-GHz Subharmonic I/Q Downconversion Resistive Mixers in 130-nm SiGe Process
In this letter, a compact multifunctional 180° hybrid suitable for sub-harmonic I/Q mixers is proposed. To feed LO and RF signals at different frequencies and distribute DC supply, the hybrid combines an out-of-phase dual balun, two in-phase power dividers based on T-junction and coupled lines, and four zero-ohm transmission lines (ZTL) into a single passive component. Chip size, insertion loss, and bandwidth can all be improved by reducing the number of passive components cascaded in the circuit. The proposed hybrid’s footprint is further minimized by employing redundant line and compensation capacitor techniques. In a 130 nm SiGe BiCMOS technology, two proof-of-concept sub-harmonic I/Q down-conversion resistive mixers with/without an on-chip LO quadrupler are implemented. Both mixers feature wideband HBT-based IF amplifiers and emitter followers, which eliminate the need for DC-blocking capacitors that constrict the IF bandwidth. The mixer, without an integrated LO multiplier, occupies an area of 0.685×0.692 mm2 and achieves a measured conversion gain of approximately 0 dB from 255 to 310 GHz. The mixer with an on-chip LO quadrupler exhibits a conversion gain of approximately -1 dB from 270 to 300 GHz and a 3-dB IF bandwidth from 0.01 to 7 GHz. Additionally, the measured image rejection ratio (IRR) is greater than 20 dB within the operating frequencies.
- 24 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Solid-State Circuits Letters
- Vol. 7, 86-89
Compact Multifunctional 180° Hybrid-Based 300-GHz Subharmonic I/Q Downconversion Resistive Mixers in 130-nm SiGe Process
In this letter, a compact multifunctional 180° hybrid suitable for sub-harmonic I/Q mixers is proposed. To feed LO and RF signals at different frequencies and distribute DC supply, the hybrid combines an out-of-phase dual balun, two in-phase power dividers based on T-junction and coupled lines, and four zero-ohm transmission lines (ZTL) into a single passive component. Chip size, insertion loss, and bandwidth can all be improved by reducing the number of passive components cascaded in the circuit. The proposed hybrid’s footprint is further minimized by employing redundant line and compensation capacitor techniques. In a 130 nm SiGe BiCMOS technology, two proof-of-concept sub-harmonic I/Q down-conversion resistive mixers with/without an on-chip LO quadrupler are implemented. Both mixers feature wideband HBT-based IF amplifiers and emitter followers, which eliminate the need for DC-blocking capacitors that constrict the IF bandwidth. The mixer, without an integrated LO multiplier, occupies an area of 0.685×0.692 mm2 and achieves a measured conversion gain of approximately 0 dB from 255 to 310 GHz. The mixer with an on-chip LO quadrupler exhibits a conversion gain of approximately -1 dB from 270 to 300 GHz and a 3-dB IF bandwidth from 0.01 to 7 GHz. Additionally, the measured image rejection ratio (IRR) is greater than 20 dB within the operating frequencies.
- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (6) , 597-600
A Sandwiched-Slab-Transformer-Based SiGe Power Amplifier Operating at W- and D-Bands
In this letter, a 75.1-151.4-GHz silicon power amplifier (PA) is devised with the help of sandwiched slab transformer, which is proposed to increase the tuning ranges of coupling coefficient, quality factor, and conductivity. Being compact in size and simple in implementation enables it to be well-applied in multiple-way power combination. Based on this device, the fabricated PA in the 130-nm silicon germanium (SiGe) process demonstrates more than 14.1-dB gain at full W-band and 77% of the D-band. From 75 to 117.7 GHz, its measured Psat is all above 16.8 dBm, while its peak point is 19.8 dBm at 100 GHz with 8.8% PAE.
- 1 June 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (6) , 597-600
A Sandwiched-Slab-Transformer-Based SiGe Power Amplifier Operating at W- and D-Bands
In this letter, a 75.1-151.4-GHz silicon power amplifier (PA) is devised with the help of sandwiched slab transformer, which is proposed to increase the tuning ranges of coupling coefficient, quality factor, and conductivity. Being compact in size and simple in implementation enables it to be well-applied in multiple-way power combination. Based on this device, the fabricated PA in the 130-nm silicon germanium (SiGe) process demonstrates more than 14.1-dB gain at full W-band and 77% of the D-band. From 75 to 117.7 GHz, its measured Psat is all above 16.8 dBm, while its peak point is 19.8 dBm at 100 GHz with 8.8% PAE.
- 20 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 2873-2877
A GaAs Colpitts VCO Using g m-Boosting and Collector-Emitter Cross-Coupling Techniques
A GaAs Colpitts voltage controlled oscillator with low phase noise is presented in this letter. Firstly, the gm-boosting technique realized by an inductor located at the emitter of heterojunction bipolar transistor is applied to relax the oscillation start-up requirements and speed up the oscillation. Moreover, a Collector-Emitter cross-coupling capacitor is adopted to improve the loaded quality factor and oscillation amplitude of the tank by reducing the transformer ratio, which improves the phase noise in turn. Finally, in proof of the concept, a voltage controlled oscillator prototype is fabricated and designed in 2-μm GaAs HBT process. The measured results demonstrate a phase noise of -137.44dBc/Hz at 1MHz offset with figure of merit of -192dBc/Hz and a tuning frequency bandwidth from 3.25 to 3.4GHz. Compared with the conventional Colpitts voltage controlled oscillator, the phase noise of the proposed voltage controlled oscillator with gm-boosting and Collector-Emitter cross-coupling techniques has improved 6.67 dB.
- 20 May 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Circuits and Systems II: Express Briefs
- Vol. 67 (12) , 2873-2877
A GaAs Colpitts VCO Using g m-Boosting and Collector-Emitter Cross-Coupling Techniques
A GaAs Colpitts voltage controlled oscillator with low phase noise is presented in this letter. Firstly, the gm-boosting technique realized by an inductor located at the emitter of heterojunction bipolar transistor is applied to relax the oscillation start-up requirements and speed up the oscillation. Moreover, a Collector-Emitter cross-coupling capacitor is adopted to improve the loaded quality factor and oscillation amplitude of the tank by reducing the transformer ratio, which improves the phase noise in turn. Finally, in proof of the concept, a voltage controlled oscillator prototype is fabricated and designed in 2-μm GaAs HBT process. The measured results demonstrate a phase noise of -137.44dBc/Hz at 1MHz offset with figure of merit of -192dBc/Hz and a tuning frequency bandwidth from 3.25 to 3.4GHz. Compared with the conventional Colpitts voltage controlled oscillator, the phase noise of the proposed voltage controlled oscillator with gm-boosting and Collector-Emitter cross-coupling techniques has improved 6.67 dB.
- 14 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (5) , 500-503
A Modified Darlington-Based Class-C VCO With Simultaneous Optimization of Phase Noise/FoM in GaAs Technology
This letter presents a modified Darlington-based (DB) class-C voltage-controlled oscillator (VCO) topology which achieves a cooptimization of phase noise and figure of merit (FoM) in GaAs technology. Both the Darlington pair and noise shifting techniques are introduced to improve the phase noise in class-C VCOs. Balanced and differential architectures are used to absorb the strength of both the Colpitts and class-C VCO topology with a simple trick of two cascaded stages in the VCO core, which elevates the VCO driving capability with no degradation of power efficiency. In addition, the startup conditions and capacitive feedback factors are derived and compared in both mathematical and simulation manners, which proves the superiority of the topology. The proposed VCO is fabricated in a GaAs bipolar high electron mobility transistor (BiHEMT) technology which demonstrates a frequency range of 2.76-2.91 GHz with a current consumption of 9.5 mA at 5 V supply, a phase noise of -138.6 to -135.9 dBc/Hz at 1 MHz offset from the carrier, an output power of -3.06 to -4.18 dBm, and a peak FoM of -191.2 dBc/Hz at 1 MHz offset. To the best of the authors' expertise, the proposed DB class-C VCO achieves both exceptional phase noise and FoM, which far outweigh that of the existing GaAs.
- 14 April 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (5) , 500-503
A Modified Darlington-Based Class-C VCO With Simultaneous Optimization of Phase Noise/FoM in GaAs Technology
This letter presents a modified Darlington-based (DB) class-C voltage-controlled oscillator (VCO) topology which achieves a cooptimization of phase noise and figure of merit (FoM) in GaAs technology. Both the Darlington pair and noise shifting techniques are introduced to improve the phase noise in class-C VCOs. Balanced and differential architectures are used to absorb the strength of both the Colpitts and class-C VCO topology with a simple trick of two cascaded stages in the VCO core, which elevates the VCO driving capability with no degradation of power efficiency. In addition, the startup conditions and capacitive feedback factors are derived and compared in both mathematical and simulation manners, which proves the superiority of the topology. The proposed VCO is fabricated in a GaAs bipolar high electron mobility transistor (BiHEMT) technology which demonstrates a frequency range of 2.76-2.91 GHz with a current consumption of 9.5 mA at 5 V supply, a phase noise of -138.6 to -135.9 dBc/Hz at 1 MHz offset from the carrier, an output power of -3.06 to -4.18 dBm, and a peak FoM of -191.2 dBc/Hz at 1 MHz offset. To the best of the authors' expertise, the proposed DB class-C VCO achieves both exceptional phase noise and FoM, which far outweigh that of the existing GaAs.
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (1) , 70-73
An Improved Colpitts VCO With Low Phase Noise Using a GaAs BiHEMT Process
In this letter, an improved balanced Colpitts voltage-controlled oscillator (VCO) with a collector-emitter cross-coupled capacitors is presented. The proposed Colpitts structure can introduce a more robust oscillation startup condition. The noise-shifting technique is used to enhance the loaded quality factor of the tank, which improves the phase noise in turn. In addition, three-bit switches composed of enhancement-mode high-electron mobility transistors (E-HEMTs) are utilized to expand the tuning range and reconfigurability of the proposed VCO. In proof of the concept, a VCO prototype is fabricated in a GaAs BiHEMT [enhancement- and depletion-mode high-electron mobility transistor (E/D-PHEMT)] process. The measured results demonstrate the best phase noise of -139.46 dBc/Hz at 1-MHz offset. To the best of our knowledge, this is the lowest phase noise among the reported ones fabricated on-chip with a similar frequency band, and it achieves a wide tuning frequency bandwidth of 21% (2.65-3.27 GHz) with peak figure of merit (FoM) of -192.26 dB and FOMT of -198.8 dB.
- 1 January 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Microwave and Wireless Components Letters
- Vol. 30 (1) , 70-73
An Improved Colpitts VCO With Low Phase Noise Using a GaAs BiHEMT Process
In this letter, an improved balanced Colpitts voltage-controlled oscillator (VCO) with a collector-emitter cross-coupled capacitors is presented. The proposed Colpitts structure can introduce a more robust oscillation startup condition. The noise-shifting technique is used to enhance the loaded quality factor of the tank, which improves the phase noise in turn. In addition, three-bit switches composed of enhancement-mode high-electron mobility transistors (E-HEMTs) are utilized to expand the tuning range and reconfigurability of the proposed VCO. In proof of the concept, a VCO prototype is fabricated in a GaAs BiHEMT [enhancement- and depletion-mode high-electron mobility transistor (E/D-PHEMT)] process. The measured results demonstrate the best phase noise of -139.46 dBc/Hz at 1-MHz offset. To the best of our knowledge, this is the lowest phase noise among the reported ones fabricated on-chip with a similar frequency band, and it achieves a wide tuning frequency bandwidth of 21% (2.65-3.27 GHz) with peak figure of merit (FoM) of -192.26 dB and FOMT of -198.8 dB.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2865-2869
An Improved UWB Bandpass Filter with a Notch-band Based on Asymmetric Parallel-coupled Line with Compact Size
This letter presents an improved UWB bandpass filter with sharp selectivity and a notch-band. Its fundamental structure is mainly based on a half-wavelength resonator using asymmetric parallel-coupled line. A center-tapped short-stub is connected at the symmetrical plane of the filter. As a result, two transmission zeros at the lower and upper passband / stopband edges are obtained. Moreover, one open parallel-coupled line is introduced to achieve a notch-band. Measured results indicate that the proposed filter has achieved a bandwidth of 110.6% from 3.05 to 10.6 GHz with a notch-band at 8.5 GHz. In addition, this filter can offer some other advantages such as sharp roll-off and compact size (0.63λ g × 0.33λ g ), which make it attractive for the practical applications in UWB systems.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2865-2869
An Improved UWB Bandpass Filter with a Notch-band Based on Asymmetric Parallel-coupled Line with Compact Size
This letter presents an improved UWB bandpass filter with sharp selectivity and a notch-band. Its fundamental structure is mainly based on a half-wavelength resonator using asymmetric parallel-coupled line. A center-tapped short-stub is connected at the symmetrical plane of the filter. As a result, two transmission zeros at the lower and upper passband / stopband edges are obtained. Moreover, one open parallel-coupled line is introduced to achieve a notch-band. Measured results indicate that the proposed filter has achieved a bandwidth of 110.6% from 3.05 to 10.6 GHz with a notch-band at 8.5 GHz. In addition, this filter can offer some other advantages such as sharp roll-off and compact size (0.63λ g × 0.33λ g ), which make it attractive for the practical applications in UWB systems.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2870-2872
A K-band Driven Power Amplifier for Automotive Radar Applications in 0.15-µm GaAs pHEMT Process
In this paper, a K-band driving power amplifier (DPA) with high gain and high output 1 dB compression point (P −1 dB, out ) is presented, which is designed and manufactured in the 0.15-µm GaAs pHEMT process. In order to achieve high gain with simple direct current (DC) bias, the four-stage common source amplifier based on self-biased techniques are employed. The DC feed network adopts a dual inductors topology, which makes the DPA achieve a high power capacity threshold. Furthermore, in order to obtain higher linearity and P −1 dB, out , the maximum power output matching are adopted in the DPA. The DPA exhibit a measured gain more than 20 dB, and a P −1 dB, out over 16 dBm from 20 to 26 GHz and the S 11 and S 22 are less than −8.5 dB within the entire band of frequencies, it is just with only one DC feed pad and serviceable for the automotive radar applications.
- 1 December 2019
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 2870-2872
A K-band Driven Power Amplifier for Automotive Radar Applications in 0.15-µm GaAs pHEMT Process
In this paper, a K-band driving power amplifier (DPA) with high gain and high output 1 dB compression point (P −1 dB, out ) is presented, which is designed and manufactured in the 0.15-µm GaAs pHEMT process. In order to achieve high gain with simple direct current (DC) bias, the four-stage common source amplifier based on self-biased techniques are employed. The DC feed network adopts a dual inductors topology, which makes the DPA achieve a high power capacity threshold. Furthermore, in order to obtain higher linearity and P −1 dB, out , the maximum power output matching are adopted in the DPA. The DPA exhibit a measured gain more than 20 dB, and a P −1 dB, out over 16 dBm from 20 to 26 GHz and the S 11 and S 22 are less than −8.5 dB within the entire band of frequencies, it is just with only one DC feed pad and serviceable for the automotive radar applications.