Wiktor Waszkowiak
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Wiktor Waszkowiak has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Arkadiusz Żak
Department of Biomechatronics Gdansk University of Technology Gdansk Poland
9 shared publications - Łukasz Doliński
Department of Biomechatronics Gdansk University of Technology Gdansk Poland
7 shared publications - Paweł Kowalski
Department of Control Engineering Gdansk University of Technology Gdansk Poland
5 shared publications - Magdalena Palacz
Gdansk University of Technology
4 shared publications - Marek Krawczuk
Institute of Mechanics and Machine Design, Faculty of Mechanical Engineering and Ship Technology, Gdansk University of Technology, Narutowicza 11/12, 80-233 Gdańsk, Poland
4 shared publications - Jacek Szkopek
Department of Biomechatronics, Faculty of Electrical and Control Engineering, Gdańsk University of Technology, 80-233 Gdańsk, Poland
1 shared publication
Latest Publications
- Open Access
- 24 July 2026
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 127 (14) , e70397
Numerical Anisotropy and Band‐Gap Formation in Finite Element Wave Propagation: Analysis and Mitigation Using Spline‐Based Elements
Numerical anisotropy and dispersion are inherent consequences of spatial discretization in finite element modeling of wave propagation. In two‐dimensional problems, these effects manifest not only as direction‐dependent phase and group velocities but also as angularly dependent numerical band gaps that may entirely suppress wave propagation. Such phenomena are often overlooked when dispersion characteristics are examined only along a limited set of symmetry directions. This paper presents a systematic analysis of numerical anisotropy in two‐dimensional wave propagation models, focusing on the spectral consequences of discretization‐induced discontinuities. Dispersion relations are examined using Bloch‐type formulations combined with mode assignment, extended Brillouin zone representations, and angular mapping, enabling a consistent interpretation of multimodal and directional effects. A spline‐based finite element formulation (spFEM) is proposed and extended from 1‐D to 2‐D problems. The method employs piecewise polynomial shape functions with enforced higher‐order global continuity, increasing the information carried by each node and reducing inter‐element derivative discontinuities. The performance of spFEM is assessed against classical FEM and a time‐domain spectral finite element method (TD‐SFEM) using Reissner–Mindlin plate models with comparable numbers of degrees of freedom. The results show that classical FEM and TD‐SFEM formulations exhibit pronounced numerical anisotropy and direction‐dependent band gaps, severely limiting their usable frequency ranges. In contrast, the proposed spFEM formulation significantly suppresses these artefacts and provides a substantially wider usable frequency range at comparable computational cost. The study demonstrates that analyzing numerical behavior beyond nominal applicability limits is essential for understanding error mechanisms and for the systematic design of improved finite element formulations.
- 24 July 2026
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 127 (14) , e70397
Open AccessNumerical Anisotropy and Band‐Gap Formation in Finite Element Wave Propagation: Analysis and Mitigation Using Spline‐Based Elements
Numerical anisotropy and dispersion are inherent consequences of spatial discretization in finite element modeling of wave propagation. In two‐dimensional problems, these effects manifest not only as direction‐dependent phase and group velocities but also as angularly dependent numerical band gaps that may entirely suppress wave propagation. Such phenomena are often overlooked when dispersion characteristics are examined only along a limited set of symmetry directions. This paper presents a systematic analysis of numerical anisotropy in two‐dimensional wave propagation models, focusing on the spectral consequences of discretization‐induced discontinuities. Dispersion relations are examined using Bloch‐type formulations combined with mode assignment, extended Brillouin zone representations, and angular mapping, enabling a consistent interpretation of multimodal and directional effects. A spline‐based finite element formulation (spFEM) is proposed and extended from 1‐D to 2‐D problems. The method employs piecewise polynomial shape functions with enforced higher‐order global continuity, increasing the information carried by each node and reducing inter‐element derivative discontinuities. The performance of spFEM is assessed against classical FEM and a time‐domain spectral finite element method (TD‐SFEM) using Reissner–Mindlin plate models with comparable numbers of degrees of freedom. The results show that classical FEM and TD‐SFEM formulations exhibit pronounced numerical anisotropy and direction‐dependent band gaps, severely limiting their usable frequency ranges. In contrast, the proposed spFEM formulation significantly suppresses these artefacts and provides a substantially wider usable frequency range at comparable computational cost. The study demonstrates that analyzing numerical behavior beyond nominal applicability limits is essential for understanding error mechanisms and for the systematic design of improved finite element formulations.
- Open Access
- 21 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (10) , 5150
Periodicity of FEM Discrete Models and Its Influence on Solutions to the 1-D Wave Equation
This paper discusses the influence of the periodicity of finite-element (FE) discrete models and its influence on solutions to the one-dimensional (1-D) wave equation. Numerical solutions to wave-propagation problems obtained via the displacement-based formulations of the finite-element method (FEM) often exhibit high-frequency behavior, which is frequently dismissed in the literature as undesired, spurious, and/or having no physical meaning. In this paper, we verify this notion by demonstrating that this behavior is not merely a computational anomaly but is due to the inherent periodic properties of discrete numerical models. Using Bloch’s theorem, we reveal and demonstrate how, at high frequencies, the discrete nature of FEM numerical models leads to the prevailing behavior governed by the periodic nature of the computational models. In order to illustrate this phenomenon, we investigate 1-D wave propagation in rods, leveraging the non-dispersive nature of the governing equation as a benchmark. In addition to the classical and specialized FEM, we analyze two alternative formulations: the time-domain spectral finite-element method (TD-SFEM) and a novel spline-based finite-element method (spFEM) proposed by the authors. The results obtained and presented explain qualitatively the origins of these numerical anomalies and suggest strategies to mitigate their effects, effectively shifting the periodicity-induced behavior beyond the range of physically relevant frequencies by appropriate selection of approximation polynomials. The authors demonstrate that this can be fully achieved only in the case of spFEM, for which the usable percentage of the available spectra of eigenfrequencies reaches 67%, while in the case of other FEM approaches discussed is significantly smaller as determined by numerical dispersion and the presence of frequency band gaps.
- 21 May 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (10) , 5150
Open AccessPeriodicity of FEM Discrete Models and Its Influence on Solutions to the 1-D Wave Equation
This paper discusses the influence of the periodicity of finite-element (FE) discrete models and its influence on solutions to the one-dimensional (1-D) wave equation. Numerical solutions to wave-propagation problems obtained via the displacement-based formulations of the finite-element method (FEM) often exhibit high-frequency behavior, which is frequently dismissed in the literature as undesired, spurious, and/or having no physical meaning. In this paper, we verify this notion by demonstrating that this behavior is not merely a computational anomaly but is due to the inherent periodic properties of discrete numerical models. Using Bloch’s theorem, we reveal and demonstrate how, at high frequencies, the discrete nature of FEM numerical models leads to the prevailing behavior governed by the periodic nature of the computational models. In order to illustrate this phenomenon, we investigate 1-D wave propagation in rods, leveraging the non-dispersive nature of the governing equation as a benchmark. In addition to the classical and specialized FEM, we analyze two alternative formulations: the time-domain spectral finite-element method (TD-SFEM) and a novel spline-based finite-element method (spFEM) proposed by the authors. The results obtained and presented explain qualitatively the origins of these numerical anomalies and suggest strategies to mitigate their effects, effectively shifting the periodicity-induced behavior beyond the range of physically relevant frequencies by appropriate selection of approximation polynomials. The authors demonstrate that this can be fully achieved only in the case of spFEM, for which the usable percentage of the available spectra of eigenfrequencies reaches 67%, while in the case of other FEM approaches discussed is significantly smaller as determined by numerical dispersion and the presence of frequency band gaps.
- Open Access
- 30 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4412
Multilayer Residual Perceptron as a Surrogate Model in Optimising the Geometry of a Periodic Beam
The paper presents an optimisation workflow for modelling of a periodic mechanical structure in the form of a multi-material, axisymmetric beam. The optimisation objective is to prescribe the positions and widths of selected band gaps within a target frequency range for three basic types of structural vibrations: flexural, longitudinal and torsional. The decision variables were geometric parameters of the unit cell and material properties of selected thermoplastics assigned to successive segments of the cell. The frequency characteristics of the beam were determined using the time-domain spectral finite-element method (TD-SFEM). This model was used to perform a sensitivity analysis using the Morris method, which showed the dominant influence of the beam geometry on the position and width of band gaps, with a relatively smaller role of material variability. Due to high computational costs of the global optimisation based on a FEM solver, a surrogate regression model in the form of a residual MLP network was developed to predict the positions and widths of the first five band gaps for each vibration type. The global search was carried out using a genetic algorithm (GA) with the surrogate model and then the results were refined using a deterministic goal-attainment method with a high-fidelity model.
- 30 April 2026
- Published by MDPI AG in Applied Sciences
- Vol. 16 (9) , 4412
Open AccessMultilayer Residual Perceptron as a Surrogate Model in Optimising the Geometry of a Periodic Beam
The paper presents an optimisation workflow for modelling of a periodic mechanical structure in the form of a multi-material, axisymmetric beam. The optimisation objective is to prescribe the positions and widths of selected band gaps within a target frequency range for three basic types of structural vibrations: flexural, longitudinal and torsional. The decision variables were geometric parameters of the unit cell and material properties of selected thermoplastics assigned to successive segments of the cell. The frequency characteristics of the beam were determined using the time-domain spectral finite-element method (TD-SFEM). This model was used to perform a sensitivity analysis using the Morris method, which showed the dominant influence of the beam geometry on the position and width of band gaps, with a relatively smaller role of material variability. Due to high computational costs of the global optimisation based on a FEM solver, a surrogate regression model in the form of a residual MLP network was developed to predict the positions and widths of the first five band gaps for each vibration type. The global search was carried out using a genetic algorithm (GA) with the surrogate model and then the results were refined using a deterministic goal-attainment method with a high-fidelity model.
- Open Access
- 8 October 2025
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 126 (19)
A Family of Higher‐Order Theories for Wave Propagation in One‐Dimensional Structural Elements
This paper proposes a systematic framework for the development and classification of higher‐order theories for modeling wave propagation in one‐dimensional structural elements. Building upon and organizing the existing higher‐order models, a generalized approach is introduced to construct an entire family of such theories with controllable complexity and accuracy. The methodology enables the inclusion of higher‐order terms in a physically meaningful and mathematically consistent manner, going beyond the classical polynomial extension of displacement fields. The proposed theories leverage traction‐free boundary conditions, leading to accurate wave representation. Preliminary considerations on their implementation in the finite element method are also discussed, laying the foundation for future work focused on advanced finite element formulations.
- 8 October 2025
- Published by Wiley in International Journal for Numerical Methods in Engineering
- Vol. 126 (19)
Open AccessA Family of Higher‐Order Theories for Wave Propagation in One‐Dimensional Structural Elements
This paper proposes a systematic framework for the development and classification of higher‐order theories for modeling wave propagation in one‐dimensional structural elements. Building upon and organizing the existing higher‐order models, a generalized approach is introduced to construct an entire family of such theories with controllable complexity and accuracy. The methodology enables the inclusion of higher‐order terms in a physically meaningful and mathematically consistent manner, going beyond the classical polynomial extension of displacement fields. The proposed theories leverage traction‐free boundary conditions, leading to accurate wave representation. Preliminary considerations on their implementation in the finite element method are also discussed, laying the foundation for future work focused on advanced finite element formulations.
- Open Access
- 4 September 2024
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 62 (3) , 601-613
The use of a genetic algorithm in the process of optimizing the shape of a three-dimensional periodic beam
Mechanical periodic structures exhibit unusual dynamic behavior thanks to the periodicity of their structures, which can be attributed to their cellular arrangement. The source of this periodicity may result from periodic variations of material properties within their cells and/or variations in...
- 4 September 2024
- Published by Polish Society of Theoretical and Applied Mechanics in Journal of Theoretical and Applied Mechanics
- Vol. 62 (3) , 601-613
Open AccessThe use of a genetic algorithm in the process of optimizing the shape of a three-dimensional periodic beam
Mechanical periodic structures exhibit unusual dynamic behavior thanks to the periodicity of their structures, which can be attributed to their cellular arrangement. The source of this periodicity may result from periodic variations of material properties within their cells and/or variations in...
- Open Access
- 16 November 2021
- Published by Elsevier in Computers & Mathematics with Applications
- Vol. 104, 14-33
A spline-based FE approach to modelling of high frequency dynamics of 1-D structures
- 16 November 2021
- Published by Elsevier in Computers & Mathematics with Applications
- Vol. 104, 14-33
Open AccessA spline-based FE approach to modelling of high frequency dynamics of 1-D structures
- Open Access
The Influence of the Grid Density of Measurement Points on Damage Detection in an Isotropic Plate by the Use of Elastic Waves and Laser Scanning Doppler Vibrometry
Damage detection in structural components, especially in mechanical engineering, is an important element of engineering practice. There are many methods of damage detection, in which changes in various parameters caused by the presence of damage are analysed. Recently, methods based on the analysis of changes in dynamic parameters of structures, that is, frequencies or mode shapes of natural vibrations, as well as changes in propagating elastic waves, have been developed at the highest rate. Diagnostic methods based on the elastic wave propagation phenomenon are becoming more and more popular, therefore it is worth focusing on the improvement of the efficiency of these methods. Hence, a question arises about whether it is possible to shorten the required measurement time without affecting the sensitivity of the diagnostic method used. This paper discusses the results of research carried out by the authors in this regard both numerically and experimentally. The numerical analysis has been carried out by the use of the Time-domain Spectral Finite Element Method (TD-SFEM), whereas the experimental part has been based on the measurement performed by 1-D Laser Doppler Scanning Vibrometery (LDSV).
Open AccessThe Influence of the Grid Density of Measurement Points on Damage Detection in an Isotropic Plate by the Use of Elastic Waves and Laser Scanning Doppler Vibrometry
Damage detection in structural components, especially in mechanical engineering, is an important element of engineering practice. There are many methods of damage detection, in which changes in various parameters caused by the presence of damage are analysed. Recently, methods based on the analysis of changes in dynamic parameters of structures, that is, frequencies or mode shapes of natural vibrations, as well as changes in propagating elastic waves, have been developed at the highest rate. Diagnostic methods based on the elastic wave propagation phenomenon are becoming more and more popular, therefore it is worth focusing on the improvement of the efficiency of these methods. Hence, a question arises about whether it is possible to shorten the required measurement time without affecting the sensitivity of the diagnostic method used. This paper discusses the results of research carried out by the authors in this regard both numerically and experimentally. The numerical analysis has been carried out by the use of the Time-domain Spectral Finite Element Method (TD-SFEM), whereas the experimental part has been based on the measurement performed by 1-D Laser Doppler Scanning Vibrometery (LDSV).
- Open Access
- 14 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (6) , 1992
Finite Element Approaches to Model Electromechanical, Periodic Beams
Periodic structures have some interesting properties, of which the most evident is the presence of band gaps in their frequency spectra. Nowadays, modern technology allows to design dedicated structures of specific features. From the literature arises that it is possible to construct active periodic structures of desired dynamic properties. It can be considered that this may extend the scope of application of such structures. Therefore, numerical research on a beam element built of periodically arranged elementary cells, with active piezoelectric elements, has been performed. The control of parameters of this structure enables one for active damping of vibrations in a specific band in the beam spectrum. For this analysis the authors propose numerical models based on the finite element method (FEM) and the spectral finite element methods defined in the frequency domain (FDSFEM) and the time domain (TDSFEM).
- 14 March 2020
- Published by MDPI AG in Applied Sciences
- Vol. 10 (6) , 1992
Open AccessFinite Element Approaches to Model Electromechanical, Periodic Beams
Periodic structures have some interesting properties, of which the most evident is the presence of band gaps in their frequency spectra. Nowadays, modern technology allows to design dedicated structures of specific features. From the literature arises that it is possible to construct active periodic structures of desired dynamic properties. It can be considered that this may extend the scope of application of such structures. Therefore, numerical research on a beam element built of periodically arranged elementary cells, with active piezoelectric elements, has been performed. The control of parameters of this structure enables one for active damping of vibrations in a specific band in the beam spectrum. For this analysis the authors propose numerical models based on the finite element method (FEM) and the spectral finite element methods defined in the frequency domain (FDSFEM) and the time domain (TDSFEM).
- 5 July 2019
- Published by Springer Nature
- p. 507-514
Smart Acoustic Band Structures
- 1 November 2017
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 409, 318-335
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method
- 1 November 2017
- Published by Elsevier in Journal of Sound and Vibration
- Vol. 409, 318-335
High frequency dynamics of an isotropic Timoshenko periodic beam by the use of the Time-domain Spectral Finite Element Method