MBMarzouk Benali

Marzouk Benali

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Marzouk Benali has a total of 46 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Accelerated green material and solvent discovery with chemistry- and physics-guided generative AI

    by Eslam G. Al-Sakkari, Ahmed Ragab, Marzouk Benali, Olumoye Ajao, Daria C. Boffito, Hanane Dagdougui

  • Open Access

    Ensemble machine learning to accelerate industrial decarbonization: Prediction of Hansen solubility parameters for streamlined chemical solvent selection

    by Eslam G. Al-Sakkari, Ahmed Ragab, Mostafa Amer, Olumoye Ajao, Marzouk Benali, Daria C. Boffito, Hanane Dagdougui, Mouloud Amazouz


  • Open Access

    Multicriteria assessment of technology pathways to produce renewable and sustainable biofuels: case study in eastern Canada

    by Georgiana Bele, Marzouk Benali, Paul R. Stuart

    One of the key pathways that can contribute to net‐zero goals is to enhance the use of renewable and sustainable biofuels. However, uncertainties remain owing to critical challenges to selecting the right sustainable biofuels technology most suitable for the longer term. These uncertainties can be partly addressed using a multidisciplinary perspective for scenarios and multicriteria decision‐making analysis. Multicriteria decision support tools (DSTs) are a powerful means to conduct the comparison of technology pathways at different technology readiness levels (TRLs). For this case study, a multidimensional DST was used to compare two technology pathways: (1) gasification combined with Fischer–Tropsch; and (2) hydrothermal liquefaction (HTL) to produce biofuels. The metrics available in the DST were examined, and five metrics related to evaluating profitability, robustness and capital efficiency as well as socio‐economic performance were selected. HTL was found to have a higher yield for renewable gasoline and diesel, largely due to higher economic performance and reduced environmental footprint as compared with the integrated gasification Fischer–Tropsch process. However, the TRL of 8–9 of biomass gasification was higher than that of HTL, which was still at 5–6, reflecting that the gasification process is essentially proven at a pre‐commercial scale. Based on sensitivity and scenario analyses, the importance of government support for capital cost and of biofuel price production incentives was identified as critical. From this comparison, HTL emerges as an attractive process for the future because of its outperformance from technical and environmental perspectives, but further demonstration efforts are still needed at the commercial scale. © 2023 Society of Chemical Industry and John Wiley & Sons, Ltd.


  • Open Access

    Ambient-pressure lignin valorization to high-performance polymers by intensified reductive catalytic deconstruction

    by Robert M. O’dea, Paula A. Pranda, Yuqing Luo, Alice Amitrano, Elvis O. Ebikade, Eric R. Gottlieb, Olumoye Ajao, Marzouk Benali, Dionisios G. Vlachos, Marianthi Ierapetritou, et al.

    Chemocatalytic lignin valorization strategies are critical for a sustainable bioeconomy, as lignin, especially technical lignin, is one of the most available and underutilized aromatic feedstocks. Here, we provide the first report of an intensified reactive distillation–reductive catalytic deconstruction (RD-RCD) process to concurrently deconstruct technical lignins from diverse sources and purify the aromatic products at ambient pressure. We demonstrate the utility of RD-RCD bio-oils in high-performance additive manufacturing via stereolithography 3D printing and highlight its economic advantages over a conventional reductive catalytic fractionation/RCD process. As an example, our RD-RCD reduces the cost of producing a biobased pressure-sensitive adhesive from softwood Kraft lignin by up to 60% in comparison to the high-pressure RCD approach. Last, a facile screening method was developed to predict deconstruction yields using easy-to-obtain thermal decomposition data. This work presents an integrated lignin valorization approach for upgrading existing lignin streams toward the realization of economically viable biorefineries.


  • Experimental and computer aided solubility quantification of diverse lignins and performance prediction

    by Olumoye Ajao, Marzouk Benali, Naïma El Mehdi

    New insights on the variability of solubility elucidated for diverse lignins, quantification thereby makes it possible to predict performance for solvent fractionation processes and polymers formulation.


  • Integrated Multiproduct Biorefinery for Furfural Production with Acetic Acid and Lignin Recovery: Design, Scale-Up Evaluation, and Technoeconomic Analysis

    by Adil Mazar, Olumoye Ajao, Marzouk Benali, Naceur Jemaa, Waleed Wafa Al-Dajani, Michael Paleologou

    Furfural is a versatile platform and multipurpose chemical that can be produced with no carbon efficiency loss from pentose sugars present in prehydrolysate streams. Existing processes for the production of furfural are typically energy-intensive with limitations to recover value-added molecules and byproducts such as lignin and acetic acid. In this work, we demonstrate a novel integrated biorefinery process for furfural production with significant sustainability improvements to current production pathways. Higher conversion efficiency for C5 sugars into furfural is achieved with a novel reactor for producing and recovering furfural in the vapor phase that has been validated at the laboratory scale. Low molecular weight and sulfur-free lignin is also recovered while minimizing energy consumption by employing membrane filtration. Synergy was observed when lignin recovery is performed prior to furfural production. On the basis of experimental results, the scalability of the process for valorizing 3200 metric tonne/day of prehydrolysate solutions that is typically combusted in kraft dissolving pulp mills was evaluated. For a furfural production capacity of 36 tonne/day, a process configuration that stands out among four proposed alternatives was identified and designed. Significant heat energy savings (99.5%) for driving the process was achieved through a heat exchanger network design for internal heat recovery, which resulted in an energy intensity of 0.47 GJ/tonne, corresponding to 1% of the energy intensity for conventional processes. The technoeconomic assessment confirmed that even the least performing process is profitable, robust, and capital-efficient as indicated by metrics such as the internal rate of return (IRR) ranging from 30% to 46%, resistance to market uncertainty (RTMU) between 0.9 and 4.3 $/$, as well as return on capital employed (ROCE) between 49% and 91%.


  • Green solvents-based fractionation process for kraft lignin with controlled dispersity and molecular weight

    by Olumoye Ajao, Jawad Jeaidi, Marzouk Benali, Omar Y. Abdelaziz, Christian P. Hulteberg


  • Acetone–Butanol–Ethanol Production from Eastern Canadian Yellow Birch and Screening of Isopropanol–Butanol–Ethanol-Producing Strains

    by Marzouk Benali, Olumoye Ajao, Naima El Mehdi, Andrea M. Restrepo, Narimene Fradj, Yacine Boumghar

    Yellow birch barks is one of the abundant species in Quebec with harvest surplus in several regions. Biofuels or biochemicals such as biobutanol can be produced using the surplus feedstock, however challenges such as the cost of pretreatment, production of unwanted by-products in the fermentation process, and the efficient recovery of solvents must be addressed to make it feasible. The objectives of this study are to establish the optimal conditions to produce biobutanol from Eastern Canadian yellow birch; to identify natural/local Clostridium sp. strains that are capable of producing Isopropanol-Butanol-Ethanol (IBE) from synthetic sugar mixtures, as candidates for metabolic engineering and to benchmark solvent producing ability with commercially available strains; and to elucidate the challenges of paradigm shift to IBE production. Alkali pretreatment of the biomass using chemical that are present in the Kraft process were performed, followed by enzymatic hydrolysis to obtain fermentable sugars and subsequent fermentation with Clostridium acetobutylicum DSM 792. The results showed that the produced Acetone-Butanol-Ethanol (ABE) solvent concentration were 6.6–8.2 g/L of acetone; 11.2–13.1 g/L of butanol; and 2.5–2.7 g/L of ethanol. The organic acids concentration was acetic acid, 1.1–1.8 g/L, and butyric acid, 0.1–0.2 g/L. Further fermentation experiments to benchmark IBE were performed using both Clostridium beijerinckii DSM 6423 and wild isolated strains, which revealed the gaps in terms of yields and the need to optimize the fermentation paradigm. Moreover, alternative process sequences for product recovery were identified, and the impact of prior liquid-liquid extraction elucidated.


  • Decision support systems for assessment of biorefinery transformation strategies

    by Marzouk Benali, Jawad Jeaidi, Behrang Mansoornejad, Olumoye Ajao, Banafsheh Gilani, Nima Ghavidel Mehr


  • Open Access

    Quantification and Variability Analysis of Lignin Optical Properties for Colour-Dependent Industrial Applications

    by Olumoye Ajao, Jawad Jeaidi, Marzouk Benali, Andrea M. Restrepo, Naima El Mehdi, Yacine Boumghar

    Lignin availability has increased significantly due to the commercialization of several processes for recovery and further development of alternatives for integration into Kraft pulp mills. Also, progress in lignin characterization, understanding of its chemistry as well as processing methods have resulted in the identification of novel lignin-based products and potential derivatives, which can serve as building block chemicals. However, all these have not led to the successful commercialization of lignin-based chemicals and materials. This is because most analyses and characterizations focus only on the technical suitability and quantify only the composition, functional groups present, size and morphology. Optical properties, such as the colour, which influences the uptake by users for diverse applications, are neither taken into consideration nor analysed. This paper investigates the quantification of lignin optical properties and how they can be influenced by process operating conditions. Lignin extraction conditions were also successfully correlated to the powder colour. About 120 lignin samples were collected and the variability of their colours quantified with the CIE L*a*b* colour space. In addition, a robust and reproducible colour measurement method was developed. This work lays the foundation for identifying chromophore molecules in lignin, as a step towards correlating the colour to the functional groups and the purity.