Walid Alnusirat
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Walid Alnusirat has a total of 47 co-authors. Here are the top co-authors by number of shared publications:
- Oleksandr Salenko
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
3 shared publications - Bohdan N. Mordyuk
G.V. Kurdyumov Institute for Metal Physics of the NAS of Ukraine, 36 Academician Vernadsky Boulevard, 03142 Kyiv, Ukraine
2 shared publications - Dmytro Lesyk
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications - Iaroslav Gnilitskyi
NoviNano Lab LLC
2 shared publications - Vitaliy Dzhemelinskyi
National Technical University of Ukraine “Igor Sikorsky Kyiv Polytechnic Institute
2 shared publications - Alexandr Potapov
Yuzhnoye Design Office
1 shared publication
Latest Publications
- 4 September 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Effect of femtosecond laser processing on optical and infrared emissive properties of stainless steel, aluminum and titanium
- 4 September 2026
- Published by Elsevier in Optics & Laser Technology
- Vol. 203
Effect of femtosecond laser processing on optical and infrared emissive properties of stainless steel, aluminum and titanium
- Open Access
- 11 June 2026
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 73 (2) , 313-331
Evaluation of cutting tool resources in flexible manufacturing systems
Flexible manufacturing systems (FMS) are widely used in modern mechanicalengineering and instrumentation due to their adaptability and high productivity. However,their effective operation is strongly dependent on accurate management of cuttingtool (CT) resources, which are subject to wear during machining processes. This studyaims to develop and justify a methodology for evaluating CT resource consumptionwith higher precision to support decision-making in FMS operations. Machining operationsare classified into positional and contour types based on their tool engagementcharacteristics. For each type, appropriate quantitative wear criteria are proposed: thenumber of discrete tool actions for positional machining and the processed volume orpath length for contour machining. A Monte Carlo-based numerical procedure is developedto estimate the actual volume of material removed during contour operations,accounting for overlapping tool trajectories and idle movements. The results confirmthat the proposed approach significantly improves the accuracy of tool workloadestimation compared to traditional time-based methods. The methodology enables more reliable forecasting of CT wear, supports predictive maintenance strategies, andimproves overall system efficiency. The proposed algorithm can be integrated intodigital manufacturing workflows, contributing to the implementation of intelligenttool management in line with Industry 4.0 objectives.
- 11 June 2026
- Published by Polish Academy of Sciences Chancellery in Archive of Mechanical Engineering
- Vol. 73 (2) , 313-331
Open AccessEvaluation of cutting tool resources in flexible manufacturing systems
Flexible manufacturing systems (FMS) are widely used in modern mechanicalengineering and instrumentation due to their adaptability and high productivity. However,their effective operation is strongly dependent on accurate management of cuttingtool (CT) resources, which are subject to wear during machining processes. This studyaims to develop and justify a methodology for evaluating CT resource consumptionwith higher precision to support decision-making in FMS operations. Machining operationsare classified into positional and contour types based on their tool engagementcharacteristics. For each type, appropriate quantitative wear criteria are proposed: thenumber of discrete tool actions for positional machining and the processed volume orpath length for contour machining. A Monte Carlo-based numerical procedure is developedto estimate the actual volume of material removed during contour operations,accounting for overlapping tool trajectories and idle movements. The results confirmthat the proposed approach significantly improves the accuracy of tool workloadestimation compared to traditional time-based methods. The methodology enables more reliable forecasting of CT wear, supports predictive maintenance strategies, andimproves overall system efficiency. The proposed algorithm can be integrated intodigital manufacturing workflows, contributing to the implementation of intelligenttool management in line with Industry 4.0 objectives.
- Open Access
- 30 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (138)) , 23-40
Forming the properties of parts obtained by FDM by modifying the surface layer using mechanical and physical-technical treatment
This study focuses on the processes and phenomena related to post-processing of FDM articles in the form of mechanical, thermal (laser), or chemical action, as well as their influence on the set of FDM-printed parts’ properties. At present, the lack of a methodological basis for the choice of post-processing methods creates obstacles in the attempt to improve the operational properties of articles and is an important problem in additive engineering. The paper investigates the post-processing of articles obtained by the method of layer-by-layer arrangement of plastic filament from the point of view of changing their mechanical and physical-technical characteristics due to the formed modified surface layer. It was noted that post-processing can be performed by mechanical action (blade cutting or abrasive processing), physical-technical, thermal (for example, laser), and chemical (etching, application of adhesive layers). As a result of such actions, a modified layer of a certain thickness is formed on the surface of the article, the structure, and properties of which will differ from the base, and its features can significantly change the operational properties of the article as a whole. The analysis of various post-processing options was performed on the basis of the functional transformation of the input parameters of the workpiece into the output ones, which made it possible to link the regularities in the formation of stresses, thermal fields, and fields of motion of matter from the parameters of the state of the surfaces, which change in the process of post-processing from the initial to the final one, and which are reflected by combinatorial sets. This approach allows one to avoid duplication of operations or individual transitions, determine the expediency of using certain techniques, increase the reproducibility of the additive process, and ensure the reliability of the finished article as a whole. The dependence of FDM articles’ properties on the state of the surfaces has been established; the corresponding functional dependences have been proposed for determining the thickness of the modified layer formed by certain mechanical or physical-technical influences. It is shown that the use of sharply sharpened tools makes it possible to obtain for PLA Ra = 3.0…3.6 μm, Rz = 20…40 μm during turning, milling, and drilling; for ABS, respectively, Ra = 1.2…1.6 μm, Rz = 5…8 μm, with a modified layer thickness of 0.15–0.65 mm and 0.1–0.25 mm, respectively. Laser exposure modifies the layer at a depth of 0.2…0.5 mm; chemical treatment with ketone vapors forms a layer with a thickness of 0.3…1.1 mm and is determined by the temperature of the saturated vapor, as well as diffusion rate
- 30 December 2025
- Published by Private Company Technology Center in Eastern-European Journal of Enterprise Technologies
- Vol. 6 (1 (138)) , 23-40
Open AccessForming the properties of parts obtained by FDM by modifying the surface layer using mechanical and physical-technical treatment
This study focuses on the processes and phenomena related to post-processing of FDM articles in the form of mechanical, thermal (laser), or chemical action, as well as their influence on the set of FDM-printed parts’ properties. At present, the lack of a methodological basis for the choice of post-processing methods creates obstacles in the attempt to improve the operational properties of articles and is an important problem in additive engineering. The paper investigates the post-processing of articles obtained by the method of layer-by-layer arrangement of plastic filament from the point of view of changing their mechanical and physical-technical characteristics due to the formed modified surface layer. It was noted that post-processing can be performed by mechanical action (blade cutting or abrasive processing), physical-technical, thermal (for example, laser), and chemical (etching, application of adhesive layers). As a result of such actions, a modified layer of a certain thickness is formed on the surface of the article, the structure, and properties of which will differ from the base, and its features can significantly change the operational properties of the article as a whole. The analysis of various post-processing options was performed on the basis of the functional transformation of the input parameters of the workpiece into the output ones, which made it possible to link the regularities in the formation of stresses, thermal fields, and fields of motion of matter from the parameters of the state of the surfaces, which change in the process of post-processing from the initial to the final one, and which are reflected by combinatorial sets. This approach allows one to avoid duplication of operations or individual transitions, determine the expediency of using certain techniques, increase the reproducibility of the additive process, and ensure the reliability of the finished article as a whole. The dependence of FDM articles’ properties on the state of the surfaces has been established; the corresponding functional dependences have been proposed for determining the thickness of the modified layer formed by certain mechanical or physical-technical influences. It is shown that the use of sharply sharpened tools makes it possible to obtain for PLA Ra = 3.0…3.6 μm, Rz = 20…40 μm during turning, milling, and drilling; for ABS, respectively, Ra = 1.2…1.6 μm, Rz = 5…8 μm, with a modified layer thickness of 0.15–0.65 mm and 0.1–0.25 mm, respectively. Laser exposure modifies the layer at a depth of 0.2…0.5 mm; chemical treatment with ketone vapors forms a layer with a thickness of 0.3…1.1 mm and is determined by the temperature of the saturated vapor, as well as diffusion rate
- Open Access
- 1 November 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (11)
Nonlinear optical properties of some nanosized ammonium dihydrogen phosphate crystals incorporated in aluminum oxide nanopores
This study explores the nonlinear optical properties of aluminum oxide (Al2O3) matrices embedded in ammonium dihydrogen phosphate (ADP) nanocrystals using third-harmonic generation (THG) techniques. The successful integration of ADP crystallites within the nanopores of the Al2O3 matrix was confirmed using x-ray structural analysis and electron microscopy. The optical absorption characteristics were examined over a wide wavelength range, revealing that the reflection and transmission spectra were notably affected by pore size and surface scattering effects. THG measurements conducted with a high-intensity infrared laser demonstrated a pronounced third-order nonlinear response, whereas second-harmonic generation was not observed. The absence of SHG can be attributed to phase mismatch and inherent material properties, including centrosymmetry and surface roughness. The comparative and Reintjes models were used to calculate the third-order nonlinear optical susceptibilities. Among these, the Reintjes model provided the most accurate fit for the experimental data. This research underscores the considerable influence of nanopore size on THG efficiency, highlighting the importance of light scattering and phase-matching conditions. These findings contribute to a growing body of knowledge regarding nonlinear optical phenomena in nanocomposite materials and offer valuable insights for future applications in photonic devices. This comprehensive analysis highlights the potential of Al2O3 matrices with embedded ADP nanocrystals to advance the field of nonlinear optics in nanocomposite materials and offers insights for prospective applications in photonic devices.
- 1 November 2024
- Published by AIP Publishing in AIP Advances
- Vol. 14 (11)
Open AccessNonlinear optical properties of some nanosized ammonium dihydrogen phosphate crystals incorporated in aluminum oxide nanopores
This study explores the nonlinear optical properties of aluminum oxide (Al2O3) matrices embedded in ammonium dihydrogen phosphate (ADP) nanocrystals using third-harmonic generation (THG) techniques. The successful integration of ADP crystallites within the nanopores of the Al2O3 matrix was confirmed using x-ray structural analysis and electron microscopy. The optical absorption characteristics were examined over a wide wavelength range, revealing that the reflection and transmission spectra were notably affected by pore size and surface scattering effects. THG measurements conducted with a high-intensity infrared laser demonstrated a pronounced third-order nonlinear response, whereas second-harmonic generation was not observed. The absence of SHG can be attributed to phase mismatch and inherent material properties, including centrosymmetry and surface roughness. The comparative and Reintjes models were used to calculate the third-order nonlinear optical susceptibilities. Among these, the Reintjes model provided the most accurate fit for the experimental data. This research underscores the considerable influence of nanopore size on THG efficiency, highlighting the importance of light scattering and phase-matching conditions. These findings contribute to a growing body of knowledge regarding nonlinear optical phenomena in nanocomposite materials and offer valuable insights for future applications in photonic devices. This comprehensive analysis highlights the potential of Al2O3 matrices with embedded ADP nanocrystals to advance the field of nonlinear optics in nanocomposite materials and offers insights for prospective applications in photonic devices.
- Open Access
- 5 November 2022
- Published by Elsevier in Optics & Laser Technology
- Vol. 158
Effects of anisotropic and isotropic LIPSS on polymer filling flow and wettability of micro injection molded parts
- 5 November 2022
- Published by Elsevier in Optics & Laser Technology
- Vol. 158
Open AccessEffects of anisotropic and isotropic LIPSS on polymer filling flow and wettability of micro injection molded parts
- 25 May 2022
- Published by Springer Nature
- p. 435-444
Influence of Multi-pin Ultrasonic Impact Treatment on Microrelief, Structure, and Residual Stress of AISI O2 Tool Steel
- 25 May 2022
- Published by Springer Nature
- p. 435-444
Influence of Multi-pin Ultrasonic Impact Treatment on Microrelief, Structure, and Residual Stress of AISI O2 Tool Steel
- 18 November 2021
- Published by Springer Nature
- p. 313-322
Comparison of Effects of Laser, Ultrasonic, and Combined Laser-Ultrasonic Hardening Treatments on Surface Properties of AISI 1045 Steel Parts
- 18 November 2021
- Published by Springer Nature
- p. 313-322
Comparison of Effects of Laser, Ultrasonic, and Combined Laser-Ultrasonic Hardening Treatments on Surface Properties of AISI 1045 Steel Parts
- Open Access
- 13 September 2021
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 88-99
About the possibility of application of laser vacuum welding for the integration of elements of heat-protective structures from powder materials
The results of studying the process of laser vacuum welding of elements of heat-shielding panels made of heat-resistant dispersion-strengthened powder materials Ni-20Cr-6Al-Ti-Y2O3 of increased strength are presented. Such materials can be used to create ultralight heat-shielding panels, which are systems integrated on the surface of aircraft from typical modules of a cellular structure. Technical solutions of heat-insulating modules are considered, which are a cellular (honeycomb) structure consisting of two plates with a thickness of 0.1 to 0.14 mm, inside which there is a thin honeycomb filler. It is shown that the small thickness of the plates and the complexity of integrating the elements into a single system significantly impair the formation of a strong connection of such elements and do not allow the direct use of the known methods of diffusion welding or vacuum brazing. It has been established that laser welding of elements of heat-shielding structures in vacuum provides satisfactory strength of the structure of the heat-shielding element as a whole. Local heating at certain points prevents deformation of the parts to be joined during the welding process. The use of a pulsed Nd:Yag laser with a power of 400–500 W, operating in the frequency range of 50–200 Hz, allows welding with or without a filler powder. It was found that the use of filler additives practically does not affect the mechanical properties of the welded joint, however, it reduces the melt zone, while increasing the density of the welded joint. Based on the results obtained, it was concluded that it is possible to use laser vacuum welding for the integration of thin elements of heat-shielding modules. It is shown that a satisfactory joint strength is achieved by ensuring high cleanliness of the surfaces of elements before welding, maintaining a high vacuum (less than 10–2 Pa) and rational thermal loading of the surfaces of the elements to be integrated. The use of the proposed process makes it possible to obtain a stronger and denser seam in comparison with the known methods of soldering multicomponent powder dispersion-strengthened materials
- 13 September 2021
- Published by OU Scientific Route in EUREKA: Physics and Engineering
- No. 5,p. 88-99
Open AccessAbout the possibility of application of laser vacuum welding for the integration of elements of heat-protective structures from powder materials
The results of studying the process of laser vacuum welding of elements of heat-shielding panels made of heat-resistant dispersion-strengthened powder materials Ni-20Cr-6Al-Ti-Y2O3 of increased strength are presented. Such materials can be used to create ultralight heat-shielding panels, which are systems integrated on the surface of aircraft from typical modules of a cellular structure. Technical solutions of heat-insulating modules are considered, which are a cellular (honeycomb) structure consisting of two plates with a thickness of 0.1 to 0.14 mm, inside which there is a thin honeycomb filler. It is shown that the small thickness of the plates and the complexity of integrating the elements into a single system significantly impair the formation of a strong connection of such elements and do not allow the direct use of the known methods of diffusion welding or vacuum brazing. It has been established that laser welding of elements of heat-shielding structures in vacuum provides satisfactory strength of the structure of the heat-shielding element as a whole. Local heating at certain points prevents deformation of the parts to be joined during the welding process. The use of a pulsed Nd:Yag laser with a power of 400–500 W, operating in the frequency range of 50–200 Hz, allows welding with or without a filler powder. It was found that the use of filler additives practically does not affect the mechanical properties of the welded joint, however, it reduces the melt zone, while increasing the density of the welded joint. Based on the results obtained, it was concluded that it is possible to use laser vacuum welding for the integration of thin elements of heat-shielding modules. It is shown that a satisfactory joint strength is achieved by ensuring high cleanliness of the surfaces of elements before welding, maintaining a high vacuum (less than 10–2 Pa) and rational thermal loading of the surfaces of the elements to be integrated. The use of the proposed process makes it possible to obtain a stronger and denser seam in comparison with the known methods of soldering multicomponent powder dispersion-strengthened materials
- Open Access
Impact of Ultrashort Laser Nanostructuring on Friction Properties of AISI 314 LVC
Laser irradiation yields a powerful tool to modify the symmetry and asymmetry features of materials surfaces. In this paper, femtosecond laser-induced periodic surface structures were applied on stainless steel AISI 314, specially hardened by a low-vacuum carburizing procedure. Symmetry modifications in the surface’s morphology and chemistry before and after the laser treatment were investigated by SEM and EDS, respectively. Coefficient of friction (COF) was observed in dry sliding condition by using block-on-ring sliding test. The results show that COF values are substantially lower after laser-induced periodic surface structures (LIPSS) surface treatment.
Open AccessImpact of Ultrashort Laser Nanostructuring on Friction Properties of AISI 314 LVC
Laser irradiation yields a powerful tool to modify the symmetry and asymmetry features of materials surfaces. In this paper, femtosecond laser-induced periodic surface structures were applied on stainless steel AISI 314, specially hardened by a low-vacuum carburizing procedure. Symmetry modifications in the surface’s morphology and chemistry before and after the laser treatment were investigated by SEM and EDS, respectively. Coefficient of friction (COF) was observed in dry sliding condition by using block-on-ring sliding test. The results show that COF values are substantially lower after laser-induced periodic surface structures (LIPSS) surface treatment.
- 15 July 2019
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 6 (3) , 263-279
Application of Laser Radiation for Intensification of Chemical Heat Treatment
- 15 July 2019
- Published by Springer Nature in Lasers in Manufacturing and Materials Processing
- Vol. 6 (3) , 263-279
Application of Laser Radiation for Intensification of Chemical Heat Treatment