MAMasoud Ahmadi

Masoud Ahmadi

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Masoud Ahmadi has a total of 19 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Revealing interphase-driven stiffness and stability in hybrid CNT/CF polymer composites via multiscale FEM

    by Masoud Ahmadi, Reza Ansari, Peyman Aghdasi, Hessam Rouhi

    A finite element-based multiscale modeling framework is developed to investigate the effect of the interphase on the mechanical behavior of carbon nanotube/carbon fiber-reinforced polyimide (CNT/CF-RP) composites. The modeling approach consists of two hierarchical steps: (i) nanoscale dispersion of CNTs within the polymer matrix, where an interphase region is explicitly incorporated to represent van der Waals interactions, and (ii) microscale distribution of carbon fibers within the equivalent CNT-reinforced polymer. Random orientations of CNTs and CFs are considered to ensure realistic representation of the composite morphology. The equivalent elastic properties obtained from the multiscale model are employed to analyze the bending, buckling, and free vibration responses of thick composite plates under various boundary conditions. Results reveal that incorporating the interphase increases the effective elastic modulus by up to ≈5%, indicating its significant role in stress transfer across the CNT–polymer interface. Hybrid reinforcement combining CNTs and CFs leads to a nearly 200% improvement in stiffness relative to the pure matrix, with notable enhancements in critical buckling loads and natural frequencies. The proposed framework effectively bridges nanoscale interfacial phenomena with macroscale structural performance, providing valuable guidance for the design and optimization of next-generation lightweight, high-strength hybrid composites for aerospace and advanced engineering applications.

  • A multiscale framework for the structural response of hybrid CNT/SiC-reinforced aluminium composite beams

    by Masoud Ahmadi, Reza Ansari, Peyman Aghdasi, Hessam Rouhi

    A multi-scale finite element (FE) framework was developed to analyse the bending, buckling, and free-vibration behaviours of carbon nanotube (CNT)-reinforced aluminium (Al) nanocomposite beams while explicitly accounting for the interphase between CNTs and the metal matrix. A three-phase representative volume element (RVE) comprising CNTs, Al matrix, and an interphase region was employed to determine the effective elastic modulus and density for CNT volume fractions of 2%, 5%, and 10%. The homogenized properties were then incorporated into macroscale FE models of cantilever beams using 2D (beam, plane-stress) and 3D (shell, brick) elements. The predicted elastic moduli showed excellent agreement with experimental data (deviation < 5%), confirming the accuracy of the homogenization scheme. CNT reinforcement substantially improved structural performance: maximum deflection decreased by ∼21%, critical buckling loads increased by 5%–27%, and the first-mode natural frequency rose by ∼16% with 10% CNT. All FE formulations produced consistent results, with 3D models additionally capturing torsional and out-of-plane effects. Overall, the proposed framework successfully links nanoscale reinforcement to macroscale mechanical behaviour, demonstrating that CNT–Al nanocomposites offer outstanding stiffness, stability, and dynamic performance for lightweight structural and aerospace applications.

  • Nonlinear electromechanical and FSI modelling of piezoelectric AFM microcantilever dynamics in air and liquid environments

    by Masoud Ahmadi, Reza Ansari, Nasima Samandari

    Piezoelectric microcantilevers are key components in atomic force microscopy (AFM), where their vibrational behaviour directly affects sensitivity, resolution, and measurement accuracy, particularly in fluid environments relevant to biological and chemical sensing. Despite extensive prior research, a systematic investigation of the geometrical effects of dual-layer piezoelectric configurations and a fully coupled electromechanical fluid–structure interaction (FSI) analysis based on realistic computational fluid dynamics (CFD) remain limited. This study presents a comprehensive three-dimensional finite-element framework to analyse the nonlinear electromechanical dynamics of piezoelectric AFM microcantilevers operating in both air and liquid environments. Geometrical nonlinearity is incorporated through large-deflection kinematics using the Green–Lagrange strain–displacement relations within a total Lagrangian formulation. First, air operation is examined through extensive parametric studies, systematically quantifying the influence of piezoelectric layer geometry (length, width, and thickness) across multiple single- and dual-layer configurations. Second, the model is extended to liquid operation through a fully coupled FSI formulation using CFD, enabling accurate representation of hydrodynamic damping and added mass effects. The numerical predictions show close agreement with published experimental and numerical results, validating both the structural and FSI frameworks. The results reveal distinct and configuration-dependent trends between air and liquid operation and provide quantitative design guidelines for optimising piezoelectric AFM microcantilevers for high-performance sensing in complex fluid environments.

  • Open Access

    Analytical modeling of the electrical conductivity of CNT-filled polymer nanocomposites

    by Masoud Ahmadi, Prashant Saxena

    Electrical conductivity of most polymeric insulators can be drastically enhanced by introducing a small volume fraction [ ] of conductive nanofillers. These nanocomposites find wide-ranging engineering applications from cellular metamaterials to strain sensors. In this work, we present a mathematical model to predict the effective electrical conductivity of carbon nanotubes (CNTs)/polymer nanocomposites accounting for the conductivity, dimensions, volume fraction, and alignment of the CNTs. Eshelby’s classical equivalent inclusion method (EIM) is generalized to account for electron-hopping—a key mechanism of electron transport across CNTs, and is validated with experimental data. Two measurements, namely, the limit angle of filler orientation and the probability distribution function, are used to control the alignment of CNTs within the composites. Our simulations show that decreasing the angle from a uniformly random distribution to a fully aligned state significantly reduces the transverse electrical conductivity, while the longitudinal conductivity shows less sensitivity to angle variation. Moreover, it is observed that distributing CNTs with non-uniform probability distribution functions results in an increase in longitudinal conductivity and a decrease in transverse conductivity, with these differences becoming more pronounced as the volume fraction of CNTs is increased. A reduction in CNT length decreases the effective electrical conductivity due to the reduced number of available conductive pathways while reducing CNT diameter increases the conductivity.


  • Multi-axial elastic–viscoplastic curves of unidirectional carbon nanotube-polymer nanocomposites considering interphase and interface debonding using finite element modeling

    by Masoud Ahmadi, Reza Ansari, Mk Hassanzadeh-Aghdam

    This paper aims to predict the elastic-viscoplastic curves of unidirectional carbon nanotube (CNT)-reinforced polymer nanocomposites under the multi-axial tensions, including bi-axial transverse-transverse, bi-axial longitudinal-transverse and tri-axial longitudinal-transverse-transverse loadings by the use of finite element (FE) modeling. The role of the interphase between the CNT and polymer matrix as well as the debonding at the CNT/interphase interface in the stress-strain curves of nanocomposites is investigated. The polymer matrix and interphase region are characterized as elastic-viscoplastic materials, while the CNT behaves as the elastic material. The present results in uni-axial loading are compared to the available numerical outcomes for indicating the accuracy of the FE modeling. The simulation of multi-axial load conditions is based on the three-dimensional representative volume element (RVE) of the unidirectional CNT-polymer nanocomposite. The effect of interface strength on the elastic-viscoplastic stress-strain curves is examined under bi-axial and tri-axial loadings.

  • Evaluating the thermal conductivity coefficient of polypropylene/graphene nanocomposites: A hierarchical investigation

    by Masoud Ahmadi, Saeed Rouhi, Reza Ansari

    In this article, we study the thermal conductivity coefficient of the polypropylene composite reinforced by graphene sheets. A hierarchical approach is used for the investigation, which is started by molecular dynamics simulation to evaluate the thermal conductivity coefficient of graphene sheets and continued by the finite element analysis to evaluate the thermal conductivity coefficient of graphene reinforced polypropylene at different temperatures. It is shown that inclusion of the graphene sheets can lead to increasing the thermal conductivity coefficient of the polypropylene, especially when the nanosheets are directed along the temperature difference. Moreover, the higher volume percentages of the graphene sheets in the polymer matrix enhance the thermal conductivity.


  • Impact resistance of short carbon fibre-carbon nanotube-polymer matrix hybrid composites: A stochastic multiscale approach

    by Reza Ansari, Masoud Ahmadi, Saeed Rouhi

    A multiscale approach is used here to investigate the impact properties of carbon fibre/carbon nanotube-reinforced polymer. For this purpose, the mechanical properties of the carbon nanotubes (CNTs) are obtained by molecular dynamics simulations. Then, they are included in the polyethene matrix, and the mechanical properties of CNT-reinforced polyethene are computed using a stochastic approach. Considering the CNT-reinforced polyethene as the matrix, the effect of adding the carbon fibres on its mechanical properties is investigated in the next step. Finally, utilizing a stochastic method, the macro-scale mechanical properties of carbon fibre/carbon nanotube-reinforced polymer are computed. Thereafter, the impact test is applied on the models. The finite element method is used to investigate the mechanical and impact properties of representative volume elements. The effects of waviness, volume percentage and aspect ratio of the carbon fibre and CNT on the mechanical properties of the multiscale composite are evaluated. It is shown that reinforcing the polyethene matrix by carbon fibres and CNTs significantly increases its impact resistance. Adding 3% and 5% volume percentages of CNT into 3%-carbon fibre/polyethene and 5%-carbon fibre/polyethene respectively, resulted in 26% and 47% improvement in the impact resistance of the composite.


  • Computational simulation of an artery narrowed by plaque using 3D FSI method: influence of the plaque angle, non-Newtonian properties of the blood flow and the hyperelastic artery models

    by Masoud Ahmadi, Reza Ansari

    Currently, cardiovascular diseases related to atherosclerosis are among the universal primary reasons for mortality. Artery stenosis is the narrowing of the artery, due to the formation of atheromatous plaque in the arterial tunica intima, a region of the blood vessel located between the endothelium and the tunica media. In the present paper, the blood flow is modeled in a stenosed artery, and the dynamic behavior of the atherosclerosis phenomenon is studied using computational analyses. To accomplish this aim, 3D finite element method (FEM) for modeling structural sections (including plaque and artery) and computational fluid dynamics (CFD) for modeling fluid part (blood flow) are coupled through a fluid-structure interaction (FSI). It is shown that the results of present FSI analysis are in good agreement with the available data in the literature. The influences of plaque geometry, in particular, plaque angle and percentage of stenosis, are investigated. Also, the effects of Newtonian and non-Newtonian properties of the blood flow and different hyperelastic artery models, including Ogden and Polynomial, are analyzed. The simulations show that with an increasing angle of the plaque, the stress of the artery increases, while the velocity of the blood flow decreases.